How to adjust the Mitsubishi system of the machining center?

Zhongshan Yisuli Machinery **** will answer for you: The operation steps of the Mitsubishi system are as follows:

1. Turn on the machine tool switch - power on button.

2. Zero: hit the knob to zrn - press the cycle start button, and the three axes will be reset to zero at the same time. (xyz can also be separated to zero:.)

Hit the knob to zrn - press z+, x+, y+, generally the z-axis must be reset to zero first) Note: Every time you turn on the machine, it must be reset to zero.

3. Install the workpiece (pressing plate or vise).

4. Hit the side of the table (plane and side) to 2 wires, the surface is within 5 wires, and it is best to play the verticality again.

5. The center rod is divided into points, and the speed is 500

6. Open the program, look at the tool, load the tool, pay attention to the blade length of the knife and the required knife length, and never install it short.

7. Simulation program - transfer program.

8. Hit the knob to DNC, feed to 10%, Rapid Override to 0%—and then quickly switch to 0% to 25% on Rapid. The tool will pause 50mm above the workpiece, and special attention is required when the tool is close to the workpiece. The feed needs to be hit to zero.

See if the distance between the tool and the workpiece corresponds to the residual value displayed by the machine.

9. Finally, adjust the speed and feed.

What are you talking about, relative or absolute, or what do you mean? 、

Summary. Mitsubishi CNC machining center is divided into problems.

Hello dear, 1. Install and stop the workpiece, install the middle rod, the speed is 600 to 1200, slowly feed the edge of the workpiece, and stop when the middle rod coincides up and down.

2. At this time, gently pat the feed handle, and the lower part of the middle rod is suddenly deviated, which is the ideal situation.

3. At this time, press zero on the digital display.

4. At this time, the value of the workpiece is obtained, and the function of 1 2 points on the digital display table is clicked.

5. At this time, the value of the center is obtained, and the machine tool workbench is shaken to the zero position of the digital display table, which is the center of the x-axis direction of the workpiece, and the center position of the workpiece can be found in the y-axis direction by the same method.

Mitsubishi CNC machining center is divided into problems.

Mitsubishi CNC machining center in the problem of the problem hello dear, 1, install the workpiece, install the bar, the speed of the posture 600 to 1200, slowly feed the side of the workpiece, and wait for the rod to coincide up and down and not swing on the pause. 2. At this time, gently pat the feed handle, and the lower part of the middle rod suddenly deviated, and then it was the situation of the number of traces. 3. At this time, press zero on the digital display.

4. At this time, the value of the workpiece is obtained, and the function of 1 2 points on the digital display table is clicked. 5. At this time, the value of the center is obtained, and the machine tool workbench is shaken to the zero position of the digital display table, which is the center of the x-axis direction of the workpiece, and the center position of the workpiece can be found in the y-axis direction by the same method. Hope it helps.

The workpiece is divided into good and invalid.

1. Switch to [handwheel] mode, move the centerer to the side of the workpiece [X-axis], 2. Press the [Settings] button, find the [W measurement] key and press it, 3. Open the pin and then find the [width measurement] key and press it, press the [Get Critical Value] key, then, get the following values, 4. Then the handwheel moves to the other side of the workpiece [X-axis], 5. Press the [Get Critical Value] key, then the following values are obtained, 6. Similarly, then the handwheel moves to the side of the workpiece [Y-axis]. 7, press the [obtain critical value] key, then get the following values, 8, then the handwheel moves to the other side of the workpiece [y axis], press the [obtain critical value] key, then complete the four sides of the boundary value, 10, press [coordinate system G54-G59] to select the coordinate system, then press the [write coordinate system] key, select [Y], 1, the handwheel moves to the workpiece plane, use the knife stick to the tool, 2, press the [set] key, 3, Sikuyou press the [T measurement] key, and then press the [write correction] key, The current tool can be measured. Hope it helps.

Kiss! Hello, I'm glad to answer your <>

The spindle positioning and setting steps of Mitsubishi 64S machining center are as follows:1Select the spindle positioning method:

In the "Parameter Setting", select "Spindle Positioning Method", which is generally the two ways of "Rotation Center Positioning" and "Mechanical Locking Positioning". Choose the right way. 2.

Set the spindle positioning coordinate system: Go to "Axis Setting" in "Parameter Setting" and select "Spindle Axis Setting" to enter the spindle coordinate system setting interface. In this interface, the spindle positioning coordinate system is set according to the actual situation, and in general, it is set according to the coordinate system of the processed workpiece.

3.Set the spindle positioning point: Enter the "Workpiece Setting" in the "Parameter Setting", select "Unknown Spindle Positioning Point Setting", and set the spindle positioning point according to the actual situation, generally at the center point of the workpiece.

4.Spindle positioning: Select "Positioning Program" in the "Manual Program" to enter the tool positioning program interface.

According to the spindle positioning mode, select the corresponding program to complete the spindle positioning step by step. 5.Test spindle positioning results:

After the spindle positioning is complete, a test is required to verify that the positioning is accurate. Judgment can be made using a measuring instrument or by checking the processing results. I hope I can help you<>

Do you have any other questions?

The method of slowing down the tool change of the Mitsubishi machining center is as follows:

1.Check whether there is any debris or knives stuck in the tool magazine, and clean up the stool and tools in the tool magazine.

2.Check whether the door of the knife magazine is closed normally, if not, it needs to be repaired or replaced.

3.Check whether the switch of the tool magazine door is normal, if not, it needs to be repaired or replaced.

4.Check whether the tool magazine motor is normal, if not, it needs to be repaired or replaced.

5.Check that the tool magazine sensor is normal, if not, it needs to be repaired or replaced.

6.Check whether the tool magazine control system is normal, if not, it needs to be repaired or replaced.

7.Adjusting the tool changer speed can be achieved by modifying the tool changer parameters.

8.Adjusting the tool change position of the tool magazine can be achieved by modifying the tool magazine parameters.

9.Adjusting the tool changer can be achieved by modifying the tool magazine parameters.

The above is the method of slowing down the tool change of Mitsubishi machining center, which needs to be adjusted according to the specific situation. It is recommended to understand the relevant knowledge and the grinding matters of jujube injection before the operation, so as to avoid unnecessary losses.

g53ofs

#2_rfp

#3_rfp

#4_rfp

Reference Point 4 sets the positions of the 1st, 2nd, 3rd, and 4th reference points based on 0 point of the basic mechanical coordinates.

mm) parameter 2038 in the set coordinates is the second reference point you want, that is, the second origin, which is used as the tool change point.

The 2038 Mitsubishi system has not been used, but please check the corresponding data sheet