How to tear off the sunscreen film from the glass

1. Roughly cut two black garbage bags into the shape of a car window or glass. Spray soapy water on the outside of the window or glass and spread one of the black garbage bags. Smooth the plastic bag.

2. Cover all surfaces in the car near the windows with tarps to protect them, such as stereos, taillights, and padded surfaces. Wear a mask before spraying ammonia.

The smell of ammonia is harmful, and different people will react differently when they come into contact with the smell of ammonia.

3. While the ammonia is still wet, use another garbage bag or multi-layer plastic wrap.

Trap the ammonia inside and apply the film tightly to the windows. Leave the windows in the hot sun, as the garbage bag will absorb the heat and help peel off the entire film.

4. Start peeling off the window film. Use your fingernails or razor blades to peel off the corner of the film as completely as possible. Be careful not to damage the defogging line.

During the process of peeling off the film, ammonia needs to be sprayed to keep the film moist. If there's a wrap that can't be peeled off, you can use a razor blade to shave it off.

5. Use ammonia and ultra-fine steel wool to remove the remaining adhesive, and wipe the glass window with a paper towel while the ammonia is still dry. Remove the garbage bag on the outside and clean the windows thoroughly with a glass cleaner.

I want to change the car film.

It is best to buy a brand of car film and a powerful store to install it before buying and installing a car film, which can reduce the risk of film and avoid buying inferior film or fakes.

It is also inconvenient for the future work of tearing the film. If you want to apply the car film yourself, you should find a closed place (such as a garage), because the film is most afraid of dust and sand, and it has a great impact on the car film on the street or in a very dusty place.

Use a special electric hair dryer for the film to blow the glass from the outside, so that the film is deformed and loose by heating, and the other side is slowly pulled;

If it is still relatively tight, you can use a special adhesive remover for automobiles to spray some between the film and the glass, and after tearing off the film, spray some places where the film has been pasted on the glass with adhesive remover, and wipe the remaining glue with a towel.

You can spray it evenly with glass cleaner first, and spray it a few more times *** can be easily removed. If the quality is poor, you should be careful and tear it slowly, if you can, use a new blade at a 30-degree angle to scrape slowly.

Friend, I don't know if you are asking how to tear off the film on the car glass? I'll take tearing off car film as an example. If it has been pasted for many years, the glue is completely dry, if the quality is not good, only the plastic paper is torn off, and the glue is still on the glass, this thing needs to be softened with a professional adhesive remover, and then slowly cleaned up little by little, if the previous paste is an inferior film, wear a mask when removing the glue, otherwise you will be smoked disgusting.

Be careful not to break the dirt remover wire when removing the rear gauge film.

It is best to soak the glass with water before tearing, so that it is easier to tear it down, and you can wipe it with alcohol after tearing, so that there will be no residual glue, and the glass will definitely be as bright as when you first bought it.

The best way is to use a hair dryer, which is the kind used in the barbershop, tear while heating, do not use small force, and do it gradually, you can tear off the whole sheet. Be patient.

Go directly to the street stall to change the film, and the film master will help you get it, no need to do it yourself.

It's easy to get rid of it with alcohol or some kind of water.

The removal method of pure water film of glass anti-solanas is as follows: 1. Vinegar is used to remove the film. Apply the vinegar evenly on top of the residual film with a cotton swab, wait for the vinegar to fuse with the glue for a while, and slowly remove it with a cloth or spatula.

Moreover, there are very few residual components of self-adhesive on the glass, and when you wipe it with paper, it will be as clean as new; 2. Remove with banana water. Banana water can remove the gum, but the effect is not very good; 3. Wind oil essence is removed from the film in spring. Apply the wind oil essence to the glue many times, slowly scrape with a knife, and be patient; 4. Alcohol film removal.

This method is more effective than the first three, apply alcohol to the film, the film will be softened, and it will be scraped off slowly with a knife; 5. Remove the film with glass film cleaning agent. Spray the glass with a special glass waterproof membrane cleaning agent on the glass to be removed, the waterproof membrane will melt immediately, and it can be wiped off with a cloth, which is very labor-saving and time-saving.

How to remove the car sunscreen film:

1. Roughly cut two black garbage bags into the shape of a window or glass, spray soapy water outside the window or outside the glass, and then sprinkle a black garbage bag to flatten the plastic bag;

2. Lay a tarp on all surfaces close to the windows to protect them, such as stereos, taillights and surfaces equipped with cushions, wear a mask before spraying ammonia, the smell of ammonia is harmful;

3. When the ammonia is still wet, use another garbage bag or multi-layer plastic wrap to trap the ammonia near the window film, so that the window is in the hot sun, the garbage bag will absorb the heat and help peel off the entire film;

4. Scrape off the corner of the patch with a fingernail or razor, and peel it off as thoroughly as possible, be careful not to damage the defogging line, in the process of tearing off the film, you should spray ammonia to keep the film wet, if there is a film that cannot be peeled off, you can use a razor blade to scrape it off.

Here's how to remove the sunscreen film:

1. Lift the corner of the car film, it is recommended to use a fingernail or tape to glue, if not, consider using a blade to peel off;

2. Cooperate with the hot air of the hot air fan or hair dryer, and slowly tear off the car film with appropriate strength and speed;

3. If there is any residual glass film glue after tearing, clean it with adhesive remover or cleaning agent; Bridge.

4. After the glass film is torn, there will be a sensitive smell of glue, which can be removed by ventilation and drying.

If you want to tear off the film, it is not impossible, and you can easily remove it by using props a little. So how to tear off the glass film, and what to pay attention to when the glass film, do you know? Now let's take a look.

1. How to tear off the glass film.

1. Dip a towel in hot water, cover the film, and after a period of time, it can be easily removed with a knife; 2. Dip an appropriate amount of detergent on the toothbrush, wipe it on the glass film, and it will be removed soon; 3. Prepare industrial alcohol, apply it to the glass film, and then wipe it with a rag to remove it easily.

2. What should I pay attention to when applying glass film?

1. When laminating the glass, it is necessary to measure the size of the position that needs to be laminated, and then cut the film according to the measured data. At this time, it is necessary to cut out the film larger than 1cm of the measured size as much as possible, which can effectively prevent the film from being small and the pasting area is round and large. And it will be more convenient when pasting in the later stage, and it can also prevent the waste of film.

2. When sticking the film, you need to prepare relevant tools, so as to make the film more convenient, but be careful, if the tool is damaged, it should be replaced in time, otherwise the glass will be accidentally scratched, which will affect the overall aesthetic effect, and it will be troublesome to replace the glass in the end.

3. When the film is pasted, it is necessary to maintain the film, you can use a professional detergent, open it and spray it on the glass, and then wipe it clean with a rag, so that the pasted glass will become brighter and smoother, and it looks very comfortable.

About how to tear off the glass film, and what to pay attention to when the glass film, I will introduce it here, do you understand? If you are not satisfied with the glass film or want to replace it, you need to tear it off and leave no traces, so as not to affect the later film.