The drilling process of the automatic drilling machine, the introduction of the usage of the automat

Dear, I'm very happy to be able to answer your <>questions

<> Hydraulic drilling machine: Hydraulic drilling machine is a special special mechanical equipment driven by hydraulic system, which is mainly used for drilling, riveting, reaming and screw processing. It fixes drill bits, saw blades, grinding wheels and other cutting tools on the support, and drives the rotation and drilling of jujube hand holes through the hydraulic system.

Advantages of hydraulic drilling machine: 1. It has high drilling accuracy and speed, and the drilling diameter is smaller; 2. The vibration of mechanical installation is small, and it is almost unaffected; 3. Low noise, large speed range, can meet the cutting and drilling of different workpiece materials; 4. All kinds of high-efficiency and high-speed tools can be used, which prolongs the tool wear cycle and reduces the tool scrap rate; 5. Low power consumption, energy saving and environmental protection.

Summary. The main components of a hydraulic drilling machine include the fuselage, engine, hydraulic pump, gearbox, electronic control system and drill bit.

Liquid drilling machine is a kind of large-scale special equipment specially designed for geological exploration, construction engineering, metallurgical industry and other industries, and it can quickly and accurately complete drilling operations.

The main components of a hydraulic drilling machine include the fuselage, engine, hydraulic pump, gearbox, electronic control system and drill bit.

TY28, can the hydraulic oil of the wind drill be used on the air leg?

TY28 wind drilling rig hydraulic oil cannot be used on air legs because its viscosity is too low to effectively resist the high pressure of air legs.

Can you play normally?

Drilling can be done normally with TY28 wind drill hydraulic oil, but due to its low viscosity, it may affect the efficiency of the drilling rig.

Ok thanks.

What is the difference between hydraulic oil and motor oil?

The difference between hydraulic oil and engine oil is that they have different viscosities, hydraulic oil has a higher viscosity, while engine oil has a lower viscosity. In addition, due to their different compositions, they also have different protective effects on the surface of metal materials.

Does it have much impact on normal drilling?

It didn't make much of a difference.

If you lift the legs, will he be the same as the oil?

The difference between the air leg and the engine oil is that the air lift leg is a special lubricant, which is mainly used in the driven Jean Tuss pneumatic components, which can effectively reduce wear, reduce noise and prolong service life. Engine oil is a general lubricant for mechanical parts, mainly used for the lubrication of internal combustion engines and other mechanical parts.

Automatic punching machineThe system can capture and analyze the sampled patterns within the camera's visual range through the computer. To operate the automatic punching machine needs to have a certain professional knowledge, so that the operation can avoid failure, but also can extend the service life, next, let's learn about the use of the automatic punching limb spring hole machine and the use of the automatic punching machine precautions.

1. Check whether the AC220V power supply is plugged in and whether the air source is turned on.

2. Punching. The general punching and binding machine has a special ruler and can be used as a benchmark to adjust the position of the punching, there is another veneer behind the binding machine can be adjusted, the general adjustable margin is left and right, the manual machine can be adjusted by the knob behind the machine, the automatic machine can be adjusted by the two knobs on the side, and the hole can be punched after the position is right.

3. Before punching work, metal objects such as pins and staples should be removed. Before binding, it is important to make sure that the glue has dried, as the overall service life of the punch binding machine will be affected by the fact that the glue is not dry. If it is the first time to use or the use experience is relatively unfamiliar, please try to avoid punching holes in the original hole, and reserve a certain margin when binding, not too far to the side.

When using a manual binding machine, pay attention to the length of the knife.

4. Hand-riveted binding. After the hole is punched in the binding machine, the rivet tube will be automatically cut and dropped in the pipe groove. Then just put the pre-cut rivet tube into the hole, and then move it to the left rivet head, insert the centering shaft into the rivet tube and then press down the handle, and the pressure only stays for 2-3 seconds.

For manual punching and binding equipment, the centering shaft must have no gaps with the silver knob on it.

2. Precautions for the use of automatic punching machine.

1. Check whether the punch and die are matched accordingly before operation, otherwise the host will be damaged.

2. The punch must be screwed and pressed before punching.

3. The screw rod and screw mother should be lubricated with oil frequently.

4. Make fixed fixtures according to the size of the processing, the number of processing holes, the size of the processing holes, and the location data of the processing holes. Tighten the clamp and the automatic turntable.

5. Set the processing data in the control and vertical resistance computer.

6. Fix the material to be processed on the automatic turntable.

7. Start the machine, and the machine will complete the processing procedures such as punching, drilling, milling, through hole, blind hole, multi-hole, high and low hole at one time according to the computer instructions and processing data.

8. After a hole is processed, the automatic drill tray will rotate at a certain angle according to the set program, align the position of the next processing hole with the processing head, and start processing again. When the entire turntable is processed, the processing process is completed in one time. Remove the machined material. Reload.

9. During the processing process, if there is a jam or lack of material, the machine will immediately alarm and stop working and wait for processing.

10. During the processing process, when the processing tool head is not sharp, the machine will also give an alarm immediately to notify the replacement tool.

Users should understand the precautions before using the automatic punching machine, so that in addition to making the operation smoother, it can also not damage the parts of the punching machine.

How to use: 1. Turn on the switch of the CNC six-sided drill, the machine starts, the control computer starts, puts the processed plate on the work surface, and turns on the automatic processing mode.

2. Input the size of the plate into the computer control system, input the parameters into the system, and be in standby mode; This ensures that the manipulator and feeding fixture are controlled by the computer and moved to a predetermined position, so that the long and short sides of the processed workpiece are adjusted and placed on the processing table.

3. The punching drill bit is automatically moved to a suitable position, the positioning plate is placed, and then the top end of the equipment is clamped together by the mechanical equipment, and then the workpiece is moved to a position close to the drilling package, and then it is moved to a suitable position.

4. The side leaning device moves to the vicinity of the plate to be processed, presses the plate, and the drill bit perforates the plate according to the preset program, and completes the punching process at the predetermined position.

5. The dust collection device sucks out the debris and other debris generated during the processing process, and the external dust collection device sucks the debris away.

6. Each processing part works together to pull the processed workpiece bucket out of the processing area vertically and convey it to the edge of the workbench to complete the stamping and slotting of the workpiece.

7. Manually take away the finished board and prepare the code scanning or programming information input of the next plate.