I want to assemble a skateboard for about 600 yuan

If it's about 600, it's really not good to group, and the bearings should be fast and recommended to be red, **60. The brick-and-mortar store costs 80There is no difference between the sand and the sand are mob, and the sand you buy the board will give the sand.

The high bridge and the low bridge are almost the same, and the low bridge is good to install a bridge mat. Thunder is recommended, neither soft nor hard. **Less than 300 can be taken down, and at least 350 in physical stores

If you want to be light, the width must be light, but if your feet are above 42, it is recommended that you buy a wide one. The wide one is a little heavier, but it's more fun than the narrow one. It is best to buy one with optical fiber if the elasticity is large, but the optical fiber is generally more than 300.

You can buy a cheaper one because it breaks down quickly. Domestic boiling point justice, 200 lets. What is imported zero, venture, filp cheap is very difficult to find, there are also, it depends on your character.

The wheels are actually wide and good. You can also narrow it. Ordinary 150 is not bad In this way, 700 can form a very good board, and 600 can be less money on the bridge, but the bridge is better to be in place in one step, because it takes a long time.

If you are in Beijing, I can give you a good physical store address.

The difference between domestic and imported panels is not too big, because it is also a consumable, and it has to be replaced in more than three months.

Sandpaper can be bought casually ** on the 25 mob on the line.

Bridges, thunder ventures, destructo or indy are basically fine, depending on whether you like hard bridges or soft bridges.

The bigger the wheel, the more comfortable it is, and the smaller the wheel wears out quickly, and the bearings are just plain bones reds.

Compared with the five-digit shots at every turn, the ** of skateboarding is very close to the people.

So, how much does it cost us to skateboard for a month?

First of all, it depends on how often you skateboard, how difficult you are to practice, what the equipment you need, etc., so let's take an average situation.

Let's say you skate two hours a day, one day a week.

At least a flip, a slide, a grind

Plate surface. If it is not elastic or bursts, change it.

Every two months.

**200 500 takes 300

Average 300 2 = 150 RMB per month

Bracket. Relatively durable.

Changed once a year. ** 250 500 takes 350

Average 350 12 = 30 RMB per month

Wheel. It's still round.

Changed every six months. **100 300 takes 200

Average 200 6 = 33 RMB per month

Bearing. Don't explode, don't change.

Changed every six months. **80 300 takes 120

Average 120 6 = 20 RMB per month

Shoe. The shoe shape collapsed before changing.

Every two months.

**100 1000 takes 200

Average 200 2 = 100 RMB per month

Drink. Drink one bottle per skateboard.

**2 6 out of 4

The average monthly is 15*4=60RMB

Public transit. $6 round trip.

The average monthly is 15*6=90RMB

There are also skateboard wax, protective gear, skateboard tickets, props, and other expenses that we ignore to ignore.

In total, we're going to spend a month for skateboarding.

483 yuan! That's 5796 a year

In ten years, you can almost buy a supercar.

Is 483 a month too much?

I believe that most people are still studying, and they are embarrassed to ask their parents for money skateboarding, so they can only save money and free up some of their pocket money.

And when we get a job and have our own income, we don't have so much time to skateboard, maybe the skateboard is left in the corner and we can't play once a month, and we don't need to change boards at all.

Everyone's situation is different, some people change a pair of Nike every week, and some people are reluctant to change the soft surface like cardboard.

There are more than 200 cheap skateboards, which are domestic boards, and generally 350-1200 are maple boards. Most of the plates higher than 6000 are imported plates.

Now it's a hundred and eighteen dollars for a regular skateboard. But regular skateboards are not very calm. I feel that if I like to play this, I will buy a slightly better one. Not easy to break. Otherwise, ordinary skateboards will break down as soon as you play them, and you will actually feel very uncomfortable.

Skateboards can be bought from the aspects of decks, brackets, wheels, and bearings.

1. a board surface

When choosing a skateboard, beginners should look at what material the board surface is made of. It is best to choose maple wood and have a layer of sand on the front to prevent slipping.

2. a bracket

It is recommended to choose a seagull bracket made of aluminum, which is not only lightweight, but also relatively strong and strong.

3. Wheels

Try to choose a large pouring wheel of PU, which will be more wear-resistant, stable, more stable and comfortable when gliding, and relatively fast to get started.

4. Bearings

It is recommended to choose chrome steel bearings, which will be more wear-resistant and not easy to rust.

Wheel size

It's important to choose the right body size and curvature for you. The deck is generally made of five, seven or nine layers of wood pressed under high pressure. Planks can be Canadian maple, Chinese maple or birch.

The sandpaper must be "sticky" to the foot, which can increase the friction between the shoe and the board.

The dimensions of the wheels are calculated in millimeters, the most common being 52-56 millimeters. For example, if a wheel is 5331, the first two numbers (53) are the diameter of the wheel, and the last two numbers (31) are the width of the wheel. The bigger the wheel, the faster, and the smaller the wheel is more suitable for playing tricks.

There are roughly four types of skateboards: double rockers, long boards, small fish boards, and large fish boards.

You need to buy your own skateboard online.

Because express shipping will be more convenient!

Generally speaking, if there is no special instructions, they are all for you to pack and deliver, and you don't have to pack them yourself.

The skateboards bought online are all unassembled. Therefore, it is necessary to assemble it yourself. The assembly method of the skateboard is as follows:

Prepare the skateboard accessories, skateboards, bridges, bridge nails, wheels and bearings, as well as the screws and nuts for each part.

1.Attach a whole piece of sandpaper to the top of the board, and then use a metal instrument to draw around it to cut out the excess sandpaper.

2.Put the bridge nail through the sandpaper into the skateboard and thread it out, attach the bridge and fix it.

3.I put eight bearings into the wheel sequentially and attach the wheel which I put the bearing on the bridge 4Adjust the hardness and softness of the bridge according to the preference of the economy, and remember that the nut of the wheel must come out to the same degree. Once installed, the entire skateboard is installed.

In fact, if you want to keep playing, you have to learn to assemble your own skateboard In fact, assembling a skateboard is very simple If you don't know how to assemble it, if the skateboard breaks down one day, you can't change it yourself or the sandpaper is broken, you can't stick it yourself, and you have to find someone to post it, so it's very troublesome, it's better to ask for others than to ask for yourself, if you want to learn how to assemble a skateboard, you can leave an email and I'll send it to you It's really very simple.

How to assemble the scooter After opening the double pedal scooter, please follow the product list and accessories list to check whether the product parts and accessories are complete. After aligning the copper marbles on the handle and the holes on both sides of the neck handle, the two bodies are tucked in. If the brass marbles of the handle do not match the hole of the neck handle, there is a danger that the handle will detach during use.

Loosen the lower lock buckle located on the side of the support frame, pull the handle up with one hand, pull the lower lever up with one hand to make the front fork stand up, let the lower lock buckle pop into the O-shaped groove of the support frame, and lock the lower lock fastening. Be sure to check the position of the locking cleavage and the state of the locking before use. Adjust the height of the handle, loosen the upper closing clasp, pull the handle up to the desired adjustment height, and then tighten the closing clasp.

If the upper rod will still loosen after the snap buckle is tightened, the nut on the snap button should be adjusted. After putting your feet on the frame panel to help you slide, press the left and right pedals respectively to make the car move, the speed of sliding is proportional to the frequency of the two feet, the more times you step on it, the faster the coasting speed, please brake to slow down when turning or going downhill, brake first when stopping, and then get off after the car stops.

Skateboard assembly configuration.

1. a board surface2: Sandpaper.

3: Bridge (bracket).

4: Wheels. 5: Bearing.

6: Bridge nail. 7: Bridge pad.

Board surface: It is generally made of seven layers of maple plank. There are also panels made of aluminum alloy, carbon fiber and other materials. The surface, head and tail of modern skateboards are all upturned.

Sandpaper: Glued to the upper surface of the board to increase friction with the sole of the shoe and facilitate the control of the skateboard. There are many colors of sandpaper, but I personally still think that black is not dazzling. Some enthusiasts cut sandpaper into a variety of shapes and stick it to the board.

Bridge: It is a part made of metal, which is fixed under the deck and the wheels are mounted on the bridge. The bridge allows the wheels to turn, and its turning speed and angle can be adjusted. Of course, it also acts as a certain shock absorber.

Wheels: It is made of polyurethane. Wheels come in different diameters, shapes, and hardnesses. The small wheels start quickly, but the stamina is insufficient; The large wheels make it easier to glide on uneven ground.

Bearings: Each wheel is equipped with 2 precision bearings, and a set of skateboard bearings is composed of a total of 8 bearings.

Bridge pins: used to connect the plate surface and the bracket. From the thread, there are hexagon and cross.

Bridge pad: It mainly plays the role of cushioning and shock absorption.