Can Tengda A301 turn wired network into wireless Wifi signal?

OK; 1. Computer setting tutorial.

1. First connect the Tengda A301 WiFi signal amplifier to the power supply, then connect the computer and the Tengda A301 device with a network cable at the same time, connect and power on, open the browser in the computer, and then enter **:, press Enter, and enter the login interface.

Note: The desktop computer is only connected to the A301 with a network cable, and does not connect to the router and other equipment; Disconnect the laptop from the wireless connection, or connect the WIFI signal of the Tengda A301.

2. Then enter the default login password of Tengda A301: admin, click OK to enter the settings interface.

3. Next, click 'Turn on Scan', then all the searched wifi signal names will appear, click the wifi name you want to enlarge the relay, enter the password, and then click "Save".

4. In the next pop-up prompt box, click "OK", and then the device will automatically restart, and you can verify whether you can surf the Internet after restarting.

Verify that the setup is complete:

1. Check whether the lights on the left, upper and right sides of the Tengda A301 indicator are "always on".

Note: If the status light is flashing and you can't access the Internet, you must check whether there is any error in the settings and check carefully.

2. Mobile phone setting tutorial.

1. Connect the Tengda A301 extender to the power supply, and the indicator light will be on.

4. Enter the settings interface, click "Turn on Scan", select the enlarged WiFi name, enter the password, and click Save.

5. After clicking "Save", in the pop-up prompt box, click "OK", the device will automatically restart, and verify whether the Internet can be accessed after the device is restarted.

Yes, plug in the network cable that has been connected to the network and you will have wireless Wi-Fi, no need to set up, and easily turn wired into wireless Wi-Fi.

Connect the phone to the A301 wireless signal, enter the setting interface in the ** column, click the system status --- the bridge status, if it shows that it has been connected, the relay is successful.

If it shows that it is not connected, please re-trunk, and the signal strength of the upper level needs to be below 70 to succeed in the trunk.

If it shows that it is connected or unable to access the Internet, it is recommended to fix the upper signal channel, use 1 6 11, set the wireless network mode, encryption mode, and security rules to be the same as A301, and try to relay again.

The reasons why the mobile phone is connected to the wifi but cannot access the Internet are: 1. The wifi itself is a problem, and the wifi may not be connected normally, resulting in the inability to access the Internet; 2. Router problems, the router may be overheated or damaged; 3. There may be broadband arrears, resulting in inability to access the Internet; 4. The wifi name contains Chinese, resulting in some mobile phones unable to connect to the Internet; 5. There may be a problem with the mobile phone system, which may cause the connection to wifi but the Internet cannot be accessed. Suggested workaround:

1. Use other mobile phones or devices to connect to wifi to try whether you can access the Internet and rule out the problem of wifi itself; 2. Restart the router to try, or restore the router to factory settings, then dial up the Internet again, and reset the wifi according to the setup wizard, or change to a new router and dial up to connect to the Internet; 3. Contact the broadband customer service to confirm whether the broadband account is abnormal, such as arrears, recharge the broadband, and then dial up the connection; 4. If the wifi name contains Chinese, it is recommended to modify it to English or a combination of English and numbers before connecting; 5. If the above reasons are ruled out, it is likely to be a problem with the mobile phone system for a long time, it is recommended to restore the factory settings or flash the phone to see if it can solve the problem.

Router Setup Problems Just reset your router.

What is a repeater? Not a router?

To transmit a signal, you need to select "Install Driver and Wireless Network Configurator" to install the driver

2.Sharing error, not a broadband connection is being shared.

Look at whether the computer is connected to the Internet through a local connection, broadband connection, or Wi-Fi connection, and which connection is used, which connection is shared.

What is shared here is a local connection, and what connection is used to access the Internet, what connection is shared.

The steps for setting up the Tengda A301 wireless router are as follows:

1. First connect the power supply, then plug in the network cable, plug the incoming cable into the WAN port, and then plug in a LAN port with the network cable connected to the computer.

3. After connecting, you will see that you will enter the corresponding login user name: admin and password: admin.

4. Enter the operation interface and click the Setup Wizard.

5. Enter the interface of the setup wizard and select the Internet access mode setting.

6. Click Next to enter the Internet access mode settings, and you can see that there are three ways to access the Internet. If it's dialing, then use PPPoE. Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer.

The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP.

7. If you choose PPPoE dial-up Internet access, you need to fill in the Internet account and password.

8. Then click Next to enter the wireless settings, you can see the channel, mode, security options, SSID, etc., generally SSID is a name, you can fill in casually, and then the mode mostly uses 11BGNFor wireless security options, choose WPA-PSK WPA2-PSK, which is so safe that you won't let people hack and rub the network. Click Next to set it up successfully.

9. Click Done, the router will automatically restart, and the router setup will be completed.