Ask the master, how to set up the FAST fr40 router Hurry, hurry, hurry

Set the IP of the outside too to the same paragraph.

I think it's better to experiment with a different network cable, or change the socket.

Plus 86165709 teaches you directly.

Two computers need to use two modems, so that you can access the Internet normally, if you have a good connection, the speed should be about the same.

Isn't your first machine dial-up? Both computers should be set fixed;

Connect to the Internet with a router, since you bought a router, don't talk about anything else, 2 computers can also share the Internet without a router, you can use a software called sysget.

You set it to automatically get the IP address.

The operation method and procedure for setting up the fastFWR310 router are as follows:

1. First of all, turn on the Internet

explorer, and then enter the address of the router", enter the username and password on the login screen (the factory setting of the username and password is admin), and click the "OK" button as shown in the image below, and proceed to the next step.

2. Secondly, after completing the above steps, if the username and password are correct, the browser will display the administrator mode interface, and the setup wizard page will pop up, see the figure below, and then enter the next step.

3. Then, after completing the above steps, select the item "PPPoE" in the interface, as shown in the figure below, and then enter the next step.

4. Then, after completing the above steps, enter the username and password provided by your ISP for broadband Internet access as shown in the figure below, and proceed to the next step.

5. Subsequently, after completing the above steps, click the "Next" button, you will see the basic wireless network parameter setting page, set it as below, see the figure below, and then enter the next step.

6. Finally, after completing the above steps, click on the "Next" button. If you change the wireless settings, the setup wizard completion screen will pop up as shown in the figure below, and restart to make the routing settings take effect, as shown in the figure below. With that, the router is set up.

The router setup is very simple, is your line connected, if not, refer to this diagram below to connect the line first.

After the line is connected as above, please operate according to the following settings:

1. Turn on your computer or laptop. After booting up, open the browser and enter it, and there is a specific look at the bottom of the router.

2. Enter the router account and password. By default, it is admin. Or you can look directly at the bottom of the router.

3. Set the wifi password according to the prompts, enter the broadband dial-up account and password, and then click to restart the router.

Fourth, check whether the mobile phone is connected to wifi normally, and whether the computer has been connected to the Internet normally. If not, please check whether the account password is correct.

Log in to your router and follow the steps to set it up. Normal router setup is simple. You can take a picture and we will guide you step by step.

The details are as follows: The Fast FW54R router is set up as follows:

1. Connect the power supply of the router, connect the external network cable to the WAN port of the router, and then plug one end of a network cable into the network port of the computer, and the other end into the LAN port of the router.

2.Open the browser of the computer, enter the IP of the router in the address bar, click the enter key to enter the router settings page, the user name is admin, the password is blank, click to log in, and enter the router settings home page.

3.Once you're logged in to the home page, select Manual settings. Then select Manual Internet Settings, and Home Dial-up users select the PPPoE connection type.

In the username and user, enter the username and password given by the ISP provider (Netcom, Great Wall, Telecom, Tietong, Cable, etc.) correctly. The connection mode selection is always filled in with the mtu value of 1492. The save is done.

4.Wireless routers also have a wireless encryption to ensure the user's wireless security. Select the wireless settings on the main page of the router's settings, select an encryption method in the security mode, any one of WEP, WPA, or WPA2, and then enter 8 or more Chinese characters or numbers as the wireless password in the security key, and the router settings will be completed after saving the settings.

5 After the setup is completed, the router will automatically restart and it is ready to use.

Line connection router and setup steps:

1. Connect the line between the network cable, the router and the computer, and start the computer and the router equipment.

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface.

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual.

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default.

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and you can click Next directly.

6. According to the setting wizard step by step setting, choose the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, then choose the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection.

7. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed.

8. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

Didn't you write your account and password? For Internet use, for example, if you run Unicom, you will be given an account for Internet access.

If you used a router and changed to a new router, you must enter the original router and disconnect, otherwise you will not be able to get on.

It's that your router is too old, and there is no official update, and the most recent update package is 2011426142162

I've got a couple of them installed on Tietong Telecom, and the speed is okay, and Netcom's encryption is too powerful.