How the Dlink DIR 615 router controls network traffic

The computer opens the browser, enters the address bar, logs in, clicks Advanced - Flow Control Settings on the router settings interface, enables the flow control check, fills in your total bandwidth (1Mbps = 1024kbps, pay attention to the conversion unit) in the WAN port bandwidth size, and then fills in the IP address of the computer you want to restrict in the rule list, select Limit the maximum ** bandwidth in the operation mode, and fill in the bandwidth size 70kbps, which means that the maximum ** bandwidth of the computer is 70kbps.

The router's traffic control settings are designed to control the speed of each computer, not the total amount of data on the computer. The method of setting the Internet speed is as follows, open the browser on the computer, enter the address bar, log in, click on the router settings interface - traffic control settings, enable the flow control check, fill in your total bandwidth in the WAN port bandwidth size (1Mbps = 1024kbps, pay attention to the conversion unit), and then fill in the IP address of the computer you want to restrict in the rule list, select the operation mode to limit the maximum ** bandwidth, and fill in the bandwidth size 70kbps, This means that the maximum bandwidth of the computer is 70kbps.

A brand new D-Link DIR 615 wireless router needs to go through 3 configuration steps from installation to Internet configuration: 1. Router installation; 2. Set the computer IP; 3. Set up the D-Link DIR 615 router.

1. Router installation;

2. Set the computer IP;

3. Set up the D-Link DIR 615 router.

Please prepare a short network cable, network cable to the home: refers to the broadband operator provides a network cable to the user's home; Please plug the network cable provided by the broadband operator into the WAN port on the D-Link DIR 615 router. Then connect the prepared network cable, one end to the computer, and the other end to the 1 2 3 4 port on the D-Link Dir 615 router.

This route can be set to the mode you want!

First of all, change the IP address of this route, not the same as the first route.

Then connect the first routed network cable to the LAN port of this route, and turn off DHCP in the settings!

The local connection properties of the computer can be set according to the first route!

For D-Link wireless routers, the basic configuration is as follows:

1. Log in to the router configuration page.

Open the browser and enter it in the address bar, the default user name of D-Link is admin, and the password is empty.

2. After logging in, choose to manually set up the Internet connection, according to your network access type to set up, there are generally three kinds, 1) DHCP: that is, the operator only provides you with the line, no other information, plug the network cable into the computer to access the Internet, in this case, the access mode is DHCP, and then click Save;

2) Static IP: Static IP, that is, the operator provides you with IP address, subnet mask, gateway and DNS address, then you need to choose the static IP method, and then fill in the above information into the router to save;

3) PPPoE: This is more commonly used, most of them are ADSL, that is, the operator provides you with a username and password, dial-up to access the Internet, then you need to choose the PPPoe method in the router, and then fill in the username and password into the router, and the following connection method selection is always.

As of now, the router can be connected to the Internet, of course, you also have to check whether your physical wiring is correct, and the incoming cable given to you by the operator should be plugged into the WAN (Internet) interface of the router.

3. Set up wireless.

In the wireless settings, you need to change the SSID (wireless network name), and then encrypt it, and it is recommended to use WPA WPA for encryption, and the password is 8 digits or more digits or more digits or letters.

1. Plug the network cable connected to the cat into the WAN port of the router, and connect any port 1234 of the router LAN port to the network card of the computer or notebook with the network cable.

2. Start the power supply of the broadband modem and router.

3. In the address bar of the IE window, enter, enter, in the dialog box that appears, enter the username and password written on the back of the router, TPLink defaults to "admin", and open the configuration interface after confirmation.

4. In the management interface of the router, select Network Parameters - WAN Port Settings, set the WAN port connection type to PPPoe (note not to select dynamic and static), enter your broadband account and password, and set up automatic connection.

Remember to click Save below.

5. Set the wireless password. Try to make the password as complex as possible, preferably a mix of numbers, English, and symbols.

Again, remember to click Save at the bottom.

Hello! The steps to install and set the wifi password for the D-Link605 router are as follows:

1. First of all, after connecting the wireless router, you need to check whether it is powered on and whether the wireless router is running normally.

2. After checking that it is correct, check the instructions on the bottom of the router, open the browser and enter the router IP, and then press Enter to enter, at this time a dialog box pops up, you need to enter the account name and password, there will be at the back of the router, in general: account name: admin password:

admin。

3. After entering the password behind the router, you can log in to the settings page of the router.

4. Click on the setup wizard on the page and follow its requirements step by step.

5. Click Next to enter the account password setting, this account password is the account password of the current network network, if you don't know, you can consult the network operator.

6. After setting the account and password for surfing the Internet, the function of wireless Internet access is set, set the wifi name and wifi password, it is recommended that the password is not too simple, it is easy to be cracked, and the encryption method can be recommended by the system.

7. Click Done, restart the router, and the settings have been successful.