The toilet is not strong when it flushes, is there any good solution?

It is recommended to change the toilet flushed into a stronger one, or change the toilet flushing system, and consult the toilet seller to see if there is a problem with the toilet, if it can't be solved, replace it with a new toilet.

You can replace the flush valve in the toilet bowl, because it is possible that the flush valve is old, which causes the underwater speed to be slow, resulting in no flushing force. It should be more energetic after changing.

When the toilet flushes the water, it may be that it has been used for a long time and there is dirt in it, so you should clean the dirt around it, and then clean the bottom of the sink of the toilet.

Increase flush volume.

The water level of the water tank is low, and the insufficient flushing amount will cause the toilet to flush weakly, open the toilet tank, adjust the drain valve, and increase the water volume of the water tank.

The specific solution: Open the toilet tank lid and find the two small mechanisms on the drain valve. There will be two water scale on it, red for full drain and blue for half drainage.

Directly adjust the two buttons on the drain valve to the bottom, and the corresponding buttons of the two scales can achieve the maximum water output.

The toilet flush is not strong, adjust it in these two places, and it will be as strong as when you bought it newly.

There are several reasons for this:

1. Weak flushing caused by clogged toilets. Dredging with a dredger, or find a longer plastic water pipe, connect tap water at one end, plug the toilet mouth at the other end, and then block the toilet mouth with something like rags, and then turn on the tap water, which will use water pressure to dredge the pipe, and when the problem is serious, the toilet should be disassembled and dredged.

2. There is too much dirt in the toilet, and the ceramic is dirty, and the flushing is weak due to not being sorted out in time. Baking soda can be used.

Or white vinegar cleaning, it is not recommended to use steel wool balls and decontamination powder, etc., will damage the ceramic glaze, can not be used, remember to sort out regularly after cleaning.

3. The water level of the inlet valve is low, resulting in weak water outlet. Remove the inlet valve and remove the inlet valve buckle. Then roll the inlet valve body counterclockwise, adjust the height of the body accordingly, and then rotate the inlet valve body clockwise to install the buckle.

Finally, the inlet valve is installed, and the filter and inlet pipe are connected to eliminate the fault.

4. If it is a side-press toilet.

It is possible that the chain of the side handle is long, and although the water stop pad has action, it will stop the water quickly, and then cause the flush to be weak, so you only need to shorten the chain to a suitable one.

5. If it is a top-press toilet.

The top pressure lever is low, which can also cause the flush to run sluggish. Open the lid of the water tank and reverse it, loosen the nut of the pressure rod, and adjust the length of the pressure bar to the appropriate level.

Reasons why toilet flushing is not strong 1. There is a problem with the quality of the toilet itself, and many businesses will choose to cut corners in the process of making toilets, so some toilets are prone to problems after being used for a long time. Therefore, when buying a toilet, you must choose a well-known brand, so that you can be guaranteed in the process of use. 2. The side handle chain of the side press and side wrench toilet is long, which causes the water stop pad to stop the water quickly, although there is action.

3. The flushing strength and water pressure of the toilet itself are insufficient, resulting in the phenomenon of weak flushing when the toilet is flushed. 4. The ceramic glaze of the toilet bowl is not smooth enough, which is easy to hang dirt, and it will also cause the flushing to be unclean.

The toilet is not flushed, and the solution is as follows:1. The toilet flush is small, which may be due to the blockage of the toilet bowl, resulting in poor drainage, and can be dredged with toilet dredging agent and leather pick.

2. There is also a situation that the water level of the inlet valve is low, resulting in weak water outlet, so it is necessary to remove the inlet valve, remove the inlet valve buckle, turn the inlet valve body counterclockwise, and adjust it to the corresponding height.

The toilet has no flushing force, which may be caused by the toilet water level being too low, so you can adjust the water level of the water tank appropriately.

1. Weak flushing caused by clogged toilets. 2. There is too much dirt in the toilet, and the ceramic is dirty, and the flushing is weak due to not being sorted out in time. 3. The water level of the inlet valve is low, resulting in weak water outlet.

4. If it is a side-pressed toilet, it is possible that the chain of the side handle is closed and long, although the water-stopping wide lifting pad has action, but it will soon stop the water, and then cause the flushing to be weak, only need to shorten the chain to the appropriate one.

At present, most of the toilets are pressed flushing, there is a press button on the water tank cover of the toilet, the back of the button is the pressure rod, the length of the pressure rod can be adjusted, the length of the adjustment is large, the water output is large when pressing, and the water output is smaller when pressing shorter. And this pressure rod is threaded, may be in the process of long-term use, the slip wire loosens, resulting in a smaller length, then in this case seepage, when we press this flush key, due to the valve opening is relatively small, the water flow is relatively slow, there will be, the toilet is not blocked, but the flush is weak. The toilet flushing is weak, don't rush to spend money to repair, first see if it is these 3 reasons 2, siphon toilet, sewage outlet flange is not tightly blocked siphon toilet, its main working principle is its internal S bend drainage pipeline, and has a long vertical downward pipeline, when the toilet flushes, the water enters the drainage pipeline, which will produce a siphon phenomenon and suck away the dirt.

This is mainly due to the tightness of the suction pipeline, the use of gravity bridge collision of water and the action of atmospheric pressure, resulting in siphon phenomenon. And if this suction line is breathable, then its suction power will be reduced. In the siphon toilet, the most likely problem is that the flange of the sewage outlet is not tightly sealed, and there is ventilation, which will lead to weak toilet drainage.