How to remove the 4 screws behind the washing machine?

Washing machine set screws in**.

Fixing screws are only available in drum washing machines, wave wheel washing machines.

Yes, there is. The screws are usually on the back panel of the drum washing machine, and there are usually 3 or 4 fixing nuts.

These screws are used to prevent the drum from moving in the washing machine during transportation.

Damage to the shock absorption system. It must be removed before use, otherwise it will make a loud noise.

And the washing machine and gearbox.

The gearing devices are placed on a special base made of styrofoam. The dewatering bucket is also fixed with a special styrofoam. The upper cover part is also fixed with styrofoam parts, so there are no fixing screws for transportation.

How to remove the fixing screws of the washing machine.

The number of fixing screws on the back of the washing machine is usually 3-6. Most washing machines have four set screws, and there will be a push-button splash plug in the accessory. After removing the screws, install the splash plug into the gap.

Not only will it prevent water or dust from getting inside the washing machine, but it will also look more beautiful.

Operation method: You can use a small wrench to twist the screw, and when the screw is loose, you can slowly pull out the long screw, and after pulling out the screw, you can pull out the plastic block, and then stuff the splash plug into the gap.

If you want to disassemble the 4 screws behind the washing machine, you can unscrew them directly with a screwdriver, and if it is a flat screw, use a flat screwdriver yourself.

First of all, it is necessary to see whether the four screws behind the washing machine can be opened with a flathead screwdriver or a Phillips screwdriver, and then choose the corresponding screwdriver. Twist it counterclockwise.

Use a screwdriver (change the cone) to disassemble, use a flat-mouth screwdriver for the flat mouth, and use a Phillips screwdriver for the Phillips one.

You should first determine what model the screw is. Then go find a professional screwdriver or wrench.

If there are four screws in the back of the washing machine, you can directly unscrew it with a screwdriver, and then the back cover behind the washing machine can be opened, and you can repair it if you want to clean it.

The screws behind the drum need to be removed when in use.

1: The four fixed spiral beams behind the back are set up to prevent damage caused by excessive shaking of the inner barrel of the washing machine during transportation, which plays a protective role.

2: There is damage but, as long as there is no leakage after several uses, the problem should not be big, Handling fixing screws, in fact, is used to fix the cylinder, after all, the drum washing machine uses a very heavy weight block in order to wash the balance of the barrel.

3: So it is easy to hurt the shock absorber during handling. This is the reason why it needs to be fixed, and one end of the fixation is generally fixed on the barrel rubber body, and the other end is on the shell. The shell is made of thin steel plate, and there is still a certain buffering effect.

4: So there is no disassembly, the shock does not work, the vibration will be very large, and the shell is affected by the shock power, there will be a slight deformation, it is very convenient to remove the screws, according to this figure, first remove the small inspection port in the middle, and then remove the screws can be used.

It needs to be dismantled, and it is best to keep it properly after dismantling.

Because the bolt is used to fix the washing machine drum, this is to prevent the washing machine drum from shaking during transportation, and the drum will be offset and damaged, resulting in the washing machine not being used normally. This is a transport protection measure, but it must be disassembled for normal use when in use. In the long run, you need to take care of these screws, and if you want to move the washing machine in the future, you need to tighten the bolts before moving, so that you can protect the drum from being damaged by impact.

If the screws are not removed, due to the action of the screws, the shock absorption of the washing machine is hindered, and the vibration cannot be eliminated, resulting in increased noise, and at the same time, it will also cause damage to the fixed parts of the barrel body, and even cause the bucket to break.

The bottom of the washing machine is removed as follows:Tools: 1 washing machine, Phillips screwdriver.

1. Turn on the washing machine and use the prepared Phillips screwdriver to unscrew the screws on the middle base of the washing machine.

2. When the screws on the base are screwed and have been fully loosened, take them out by hand, and the base can also be taken out directly.

3. Take out the middle-aged base of the washing machine. It is best to tilt the base slightly and take it out at the place where the diameter of the washing machine bucket is the longest.

4. Since the washing machine has not been cleaned for a long time, it can be seen that the inner cylinder of Wang Peiyuan's base hides a lot of dirty things, which is also the reason for the breeding of bacteria.

5. Put the taken out base under the water stream and rinse it with water, and wash it like new.

The fixing screws of the washing machine wave wheel, in order to prevent users from falling off when they are used, are glued and fastened, so they are not easy to disassemble.

You can use a hair dryer to tighten the screws of the wave wheel and heat it slowly.

Take care to prevent heat damage to other plastic parts.

After the glue at the adhesive site is heated and soft, it can be removed with a screwdriver.

The wave wheel fastening screws of the washing machine are right-handed threads (positive threads), which are tightened in a clockwise direction, and are loosened and disassembled by rotating them counterclockwise with a screwdriver.