What should I do if IWC repairs the watch glass with water?

1. Use silica gel to dry the granules. If water enters the case, a granular substance called silicone can be used to put the watch in an airtight container with the water that has accumulated water, and after a few hours, remove the watch and the water will disappear. This method is simple and economical, and the accuracy and longevity of the watch will not be compromised in any way.

The silica gel, which has been absorbed many times, can be dried at 120 degrees for several hours, has a renewable water absorption capacity, and can be used again and again.

2. Bake hot with an electric light bulb. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the table tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes, which will eliminate the moisture. Be sure not to bake the watch mask directly near the fire to prevent the watch from being deformed by heat.

3. Wear the watch backwards. You can also wear the mask with the cover facing inward and the bottom shell facing outward, and wear it on the wrist, and the moisture will be eliminated after two hours. If the water ingress is severe.

4. Send it to the watch shop to wipe the oil. None of the above three methods can remove water vapor, and it should be sent to a repair shop immediately to wipe the oil to remove moisture from the movement and prevent rust on the parts.

5Dry with a hair dryer, the temperature should not be too high, and the wind will be mild until the moisture on the glass is not visible.

There are two simple and effective methods, one, put the watch and a few packets of new desiccant together in a plastic bag, tie it tightly without air leakage, and let it sit for two days. Second, put the watch under a lit ordinary light bulb and leave it overnight. Do not blow the watch directly with a hair dryer, it will damage the watch.

Method 1: If water enters the case, you can use a granular substance called silicone to put it into a closed container with the watch that has accumulated water, and after a few hours, take out the watch and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

Method 2: If the water ingress is not serious, but there is a layer of mist in the glass, then several layers of toilet paper can be used.

or flannel cloth that absorbs moisture will be tightly wrapped around the table, at a distance of 40 watt bulbs.

Bake at 15 cm for about 30 minutes to eliminate moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours.

If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the sensitive oil to remove the moisture from the movement to avoid rust on the parts.

Method 3: Put the skin on the inner branch and the bottom shell outward, and put it on the wrist, and the moisture can be eliminated after two hours. If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

Special attention should be paid to the fact that if the electronic watch is flooded, the electronic should be removed in time. Whether it's a mechanical watch.

Or an electronic watch, if the water ingress is serious, it should be sent for repair in time.

The repair address is located at:Huangpu District, ShanghaiRoom 1003, 10th Floor, Hongyi International Plaza, No. 299 Nanjing East Road

If you accidentally get water inside your case, you can use a granular substance called silicone to put your watch in a metre-closed container with the watch that has been waterlogged, and after a few hours, you can remove your watch and the water will disappear. This method is simple, convenient and economical, and does not compromise the accuracy or longevity of the watch. In addition, the silica gel that has absorbed water many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

If the mechanical watch is soaked in water, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it at about 15 cm near the 40-watt light bulb, and bake it for about 30 minutes, and the water vapor in the watch can be eliminated. Do not bake the watch close to the fire, so as not to deform the watch by heat. It is recommended that it is best to send it to the repair center to wipe the oil for maintenance to prevent the parts inside from rusting.

Water and fog into the watch has the greatest impact on the watch movement, and it should be dealt with in time to prolong the service life of the watch. If not treated in time, the residual moisture will easily cause the internal movement to oxidize and rust, resulting in inaccurate watch timekeeping and watch failure.

If the watch is seriously flooded, please send it to the repair center immediately for treatment, otherwise it will cause many metal parts inside the movement to oxidize and rust due to water vapor, causing greater damage.

IWC watch is a better high-end watch, you must go to the regular maintenance point to open the cover and shine the heat lamp to steam the water vapor inside, it is best to combine maintenance together, it is good for the service life and punctuality of the watch.

Go to the watch shop. Go to the watch shop.

If the watch is flooded, it can only be sent to the repair station for repair. After opening the watch, removing the water vapor in the watch, and lubricating the rotating part with oil, it can be used normally.

You can try to store it in a rice tank, which can effectively absorb water in a dry environment; If the effect is not obvious, it is recommended to go to a repair shop for repair.

The solution to the water in the watch and the fog on the mirror:

Wrap the watch tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, and bake it under the light bulb for about 30 minutes to eliminate the water mist inside, but do not put it close to the light bulb or bake it directly, so as not to cause the surface to be deformed by heating.

Wear the surface inwards and the bottom case outwards on your wrist to remove the mist from the surface after a few hours.

If you have silicone, you can put the silicone and the watch in water into a closed container, and after a few hours, take the watch out again, and the water mist in the watch will disappear.

If the water ingress of the watch is serious, it is best to send it to a watch shop to wipe the oil and eliminate the water in the watch to avoid rust on the parts of the watch.

Note: In order to prolong the service life of the watch, you should try to avoid fog and water droplets in the waterproof watch, do not wear the watch when washing your face, bathing, swimming and other "hydrophilic" activities, do not be affected by water vapor and hot vapor, and pay more attention not to be exposed to rain on rainy days.

1. After the watch is flooded, you can use several layers of toilet paper to wrap the watch tightly, put it in the sun and expose it to the sun for half an hour, and after half an hour, the water vapor in the watch will turn into nothing. Please do not leave your watch in the sun for too long to avoid deformation of the watch.

2. Put the granular silicone into a closed container with the watch that has accumulated water, and after a few hours, take out the watch, and the water in the watch is all gone. This method does not compromise the accuracy or longevity of the watch. After the silica gel has been absorbed many times, after drying for several hours, the water absorption capacity is renewable, and it can be used again and again.

3. Put the surface face inward, the bottom shell facing outward, and put it on your arm, and the moisture will disappear after two hours. If the water ingress is severe, it is best to take it to a watch repair center immediately to wipe the oil and remove the moisture from the movement to avoid rust on the parts and unnecessary trouble.

After the watch is flooded, it is necessary to contact the repair and replacement in time, and the damaged components in the watch sometimes need to replace the entire movement.

Wrap a layer of toilet paper first, thicker.

Let stand in a dry place.

Take it to the watch store for maintenance.

Don't let the small be the big one.

Rice has a good water absorption effect, and every family has rice, and it is easy to use. After 24 hours of placing the watch in the rice, most of the water is absorbed. Finally, take out the watch and gently wipe off the rice dust.

If there is a problem with the watch, call the customer service first, and the customer service in Guangzhou can try to call the 29872673Remember to add the area code of Guangzhou in front. Then the customer service will tell you how to go after the sale. To the after-sales inspection and maintenance, just follow the process.

If there is a problem with the watch, I recommend going directly to the watch after-sales center. After-sales is not only more professional technicians, but also the instruments are imported, more precise, and **also very transparent, will not be messy**. When not to go to a regular after-sales center.

Otherwise, if you are trapped, you can only blame yourself.

First of all, don't be in a hurry, find a place to vacate the water, and then dry it out in the sun.

1. When there is very little fog, just put the watch in a cool and ventilated place and let it dry for a period of time, and the fog will dissipate.

2. Wear the watch backwards, put the dial facing inwards and the bottom of the watch facing outward, and wear it for a few hours to achieve the defogging effect.

3. Place the watch in a sealed container with granular silicone, and after a few hours, it can also achieve the effect of defogging. If there are no silica gel particles, you can also use rice instead, and after a day of resting, the mist can also be sucked away.

4. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the table tightly, and bake it for about 30 minutes at a distance of 15 cm from a 40-watt light bulb to eliminate the moisture. Do not bake the watch close to the fire to avoid deformation of the watch.

IWC Watch Water Ingress Repair After-sales Center is located in Room 1502, Block A, Office Building, Victoria Plaza, No. 103, Tiyu West Road, Tianhe District, Guangzhou.

The waterproof device is also installed in these three places: add a rubber ring to the shank, add a rubber ring on the threaded edge of the back cover of the sealing ring, shank and other parts, and make the surface tight. With these designs, the watch is waterproof.

But whether the watch can forever. Absolutely waterproof? No.

Originally, it was absolutely waterproof according to the design requirements, but because we have to wind it every day. It is necessary to dial the needle frequently, for a long time, the waterproof ring will be worn and there will be gaps, and the sweat on our hands and necks will also corrode the waterproof rubber ring on the back cover, even if there is no sweat corrosion, the rubber ring itself will age and loosen with time.