What to do if your Rolex watch gets into the water, and what to do if your watch is repaired 5

Room 2513, 25th Floor, Diwang Building (Shun Hing Plaza), No. 5002 Shennan East Road, Luohu District, Shenzhen, Guangdong Province] will answer for you.

1. If the water ingress into the watch is not very serious, but there is a little water mist in the watch, then you can hold it with a few pieces of dry paper, and then take the watch to a 40-watt bulb and bake it for half an hour, and the water vapor in the watch can be removed. Or wear the watch backwards for several hours, which can also play a role in eliminating water vapor in the watch.

2. After-sales professional technician tips: If the watch is very serious in water, then it can only be repaired by opening the cover, because the watch is more water-in, indicating that the waterproof ring function of the watch is aging, so it should be replaced, and then the watch is more water, which has caused the movement parts in the watch to be stained with water, and if not taken care of in time, the parts will be rusted and harmed.

3. Therefore, most watches are repaired when they are in water, and it is recommended to open the cover for maintenance. When the watch is repaired by water, it is not only necessary to remove the water vapor in the watch, but also to take care of the movement parts in the watch.

Hello, glad to answer for you!

1. If the water ingress is not serious, but there is a layer of fog on the surface, you can use toilet paper or flannel cloth that is easy to absorb moisture to wrap the table tightly.

3. If the water ingress is serious, it is best to send it to the after-sales center for maintenance immediately.

If you have any questions, please call** Please feel free to call.

What to do if the watch gets water.

It is normal for the watch to get water, if the water is not serious, but there is a layer of fog in the watch glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it for about 30 minutes at a distance of 15 cm from a 40-watt light bulb to eliminate water vapor. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours.

Of course, there are also some daily repair methods for watches to get into the water:

1. Dry the granules with silica gel. If water enters the case, you can use a granular substance called silicone to put the watch in an airtight container with the waterlogged watch, and after a few hours, remove the watch and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

2. Bake with a light bulb. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating.

3. Wear the watch backwards. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours. If the water ingress is severe.

[Watch maintenance and repair can refer to the service center of Xidan Joy City Office Building, Xicheng District, Beijing] to provide Rolex watch strap customization, cleaning and maintenance, identification, refurbishment, fault repair, watch appearance and replacement of damaged parts, and strap replacement services. Our technicians have undergone strict professional skills training and provide two years of after-sales guarantee services. The service center is guided by the watch manufacturer on the spot**, **transparent, no hidden consumption, no additional charges.

Method. 1. Put the surface face inward, the bottom shell facing outward, and wear it on the wrist, and the water vapor can be eliminated after two hours. If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

Method. 2. If the watch is soaked in water, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it near a 40-watt light bulb about 15 cm, bake for about 30 minutes, and the water vapor in the watch can be moisture. Do not bake the watch close to the fire, so as not to deform the watch by heat.

Method. 3. Put the granular silicone into a closed container with the watch that has accumulated water, and after a few hours, take out the watch, and the water will all disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

First, when the watch enters water and fog, the easiest way is to wear the watch on the wrist, that is, let the watch reflect inwards and the bottom case of the watch outward. After a few hours, you will notice that there is less and less moisture inside the watch.

Second, prepare some paper towels or moisture-absorbing flannel, wrap the watch tightly, place it on a 40-watt light bulb about 5 cm, and bake it for about half an hour. After that, you will notice that the moisture in the movement slowly disappears.

Thirdly, fog vapor can also be removed by basking in the sun. First open the back cover of the watch, then wrap the watch completely with a paper towel or moisture-absorbing flannel cloth, and take it to the sun for most of the day to remove the moisture in the movement.

Fourth, after the watch is flooded, you can first open the back cover of the watch, remove the battery, and use the hair dryer to aim at the watch on low gear. After blowing until it is completely dry, reattach the back cover. When installing, you can also check whether the sealing ring is aging and broken, and remember that the back cover must be fastened if it is in good condition.

Fifth, dry the granules with silica gel. Put the silicone granular substance in a closed container with the watch that has accumulated water, and after a few hours, remove the watch and the water will disappear.

Water into the watch Generally, there is water mist or water droplets on the watch glass, which will corrode the movement after a long time, resulting in inaccurate or non-time, so the earlier the watch water ingress treatment time, the less damage to the movement, the recommended treatment method is as follows:

Law. 1. Place the vent - dry the watch with a dry paper towel and then place it in a cool and dry vent for a few hours, and do not place the watch directly in the sun or dry, which is to prevent water mist from flowing into the movement.

Law. 2. Silicone drying - for the water inlet of the mechanical watch, you can use the granular substance of silica gel to absorb water, put the two in a closed container, and take it out after a few hours, and the water mist inside will be cleaned up; If it is a quartz point clock, you can take a few small pieces of calcium chloride, wrap them in gauze, and then open the electronic watch cover and seal it.

Law. 3. Wipe oil and remove rust - method 1 and method 2 can only clear a slight water mist, and for some more serious water ingress, these two work earlier, which is not enough for the rescue time of the movement, at this time it is best to find a professional watch repair center for ** maintenance, oil wiping treatment.

The water ingress of the watch should be dealt with in time, otherwise the water ingress for too long will damage the internal parts of the watch, resulting in rust of the movement parts, and these parts are very sophisticated watch configurations. If the watch gets water, it is recommended that you take the watch to a service center immediately to avoid further damage to the watch.

If you find that the watch is flooded, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it about 15 cm near a 40-watt light bulb, and bake for about 40 minutes, and the water vapor in the watch can be eliminated. Do not bake the watch directly near the heat, so as not to deform the glass by heating. Because although there is no moisture on the dial, there may still be water in the movement, and the movement will rust and cause damage to the movement after a long time.

After the watch is flooded, it is recommended to find a professional repair outlet as soon as possible for the master to check and deal with it, which can reduce your unnecessary losses.

Generally speaking, there are only three places where water can enter the watch movement: the handle (handle), the watch mask and the back cover. The waterproof device is also installed in these three places: add a rubber ring to the shank, add a rubber ring on the threaded edge of the back cover of the sealing ring, shank and other parts, and make the surface tight.

Water and fog into the watch has the greatest impact on the watch movement, and it should be dealt with in time to prolong the service life of the watch. If not treated in time, the residual moisture will easily cause the internal movement to oxidize and rust, resulting in inaccurate watch timekeeping and watch failure.

If the watch is seriously flooded, please send it to the repair center immediately for treatment, otherwise it will cause many metal parts inside the movement to oxidize and rust due to water vapor, causing greater damage.

Remove the cover and dry it with a hair dryer at a temperature not too high. If you want to use special tools, you should go to the watch shop to repair it.

Rolex Watch After-sales Service Center: 400-659-0877 Rolex watch water ingress treatment method:

1.The most important of the three defensive features of a Rolex watch is water resistance. Even if a mechanical watch is not exposed to water in a relatively humid environment, prolonged exposure to moisture can cause the watch parts to rust.

The mechanical tightness of a mechanical watch depends mainly on the structure of the case and the tightness of the waterproof gasket.

2.A very important part of the maintenance of a mechanical Rolex watch is water resistance. First of all, you need to know about waterproof mechanical watches. If the waterproof standard is 30 meters or 3 atmospheres.

In life, we have the opportunity to contact water more frequently, go to the bathroom to wash your hands, before eating to wash your hands, these will be in contact with water, we can't wash our hands when the watch is taken off, so that after a long time it will get into the water, even a Rolex watch is no exception, although the Rolex watch is durable, but regular contact with water can not avoid the watch water.

The safe way to get a Rolex watch in water is to send it to the after-sales service center, not to wait until the movement is rusted to repair it in order to save a moment, the cost will be far more than it is now. The after-sales address is in Room 1102 on the 11th floor of Block D of Bloomage International Center in Chaoyang International Trade Center, which is why I want to say that the prevention of watch water is the main thing, when buying a Rolex watch, you should first ask about the waterproof level of this watch, generally speaking, within 50 meters, you can prevent water droplets splashed on the dial by hand washing, or raindrops falling from raindrops, but remember to wipe it off in time; 100-200 meters can wash hands and swim shallowly; 500 meters or more can be dived, how deep you can dive you need to ask the store staff. Generally speaking, the waterproof is cold water, and it is in a static state, so in case you encounter hot water, you should pay attention, in the environment with large temperature changes, it is easy to cause fogging or condensation of water droplets on the dial, so this is also something to pay attention to.

The watch is a kind of precision timekeeping instrument, which has a high price and a long service life. The quality of the watch is a matter of great concern to users. Therefore, people always strive for excellence when buying watches, and choose the best of the best.

But how do you choose a watch that is of satisfactory quality? Usually, people only judge the worst of the watch by listening to the sound of the watch machine, which is unscientific. Because the quality of the watch is mainly based on the accuracy of its actual timekeeping.

The sound emitted by the watch machine when it is running is balanced, clear and free of noise can only indicate that the watch is not faulty, and does not indicate the quality of the watch and the only way to choose a watch. It is also necessary to choose from the following aspects:

Inspect the exterior parts of the watch.

The exterior of the watch can be inspected from the case, glass, dial, and hour, minute, and second hands. The case should be free of sand holes and obvious scratches, with symmetrical edges and corners; The screwing place between the back cover and the upper shell should be tight; The distance between the two rings and the case is equal, and the hole for installing the earrings should be centered at the end of the case foot, and the depth of the hole is appropriate so that the ring is not easy to fall off; The watch glass should be free of defects and scratches, transparent and bright; The three needles are installed correctly, and there should be correct safety clearances between the needles and the needles, the glass and the dial; The dial and hands are plated with a good finish, no marks, and the dial scale lines or luminous dots are complete; There is a gap of about 0 1 0 3mm between the handle and the case.

Check the sensitivity of your watch.

The sensitivity of a watch refers to the flexibility with which its balance wheel automatically swings. The way to check is as:

1) Gently shake the watch that has not been wound and has stopped moving, and observe the movement of the second hand with the help of the power of shaking: if the second hand stops moving in a short time, it means that the watch can be fully wound (that is, the clockwork is not current), and the sensitivity is high; If the second hand continues to move for a long time, it means that the watch cannot be fully wound (i.e., the clock also stores torque), the sensitivity is not high, or the watch is faulty.

2) Slowly turn the handle of the watch that has not been wound to stop moving, and observe the start of the second hand: the less the upper handle, the earlier the second hand starts, the higher the sensitivity of the watch; Otherwise, the sensitivity is low or there are other faults in the meter. However, it should be noted that due to the stiffness of the hairspring, the fast swing watch has to be a little more wound than the traditional frequency (18,000 times per hour) to swing.

A watch with high sensitivity will continue to move for a long time after a full wind.

1.How well an analogue meter is moisture resistant depends on the moisture barrier ring, and the aging or brittleness of the moisture barrier will reduce the usefulness of this function of the analogue meter. This is the key to properly replacing the waterproof ring.

Due to the hot and humid temperatures, the grease inside the watch can easily condense, causing the time mechanical watch to stop, slow down, or stop altogether due to errors.

2.If your watch gets wet, you need to do something to save it after being invaded by water. Wrap the table tightly with toilet paper or absorbent cotton, place it about 15 cm near a 40-watt bulb and allow it to dry for about 30 minutes to allow the water vapor in the table to settle.

Do not leave the glass to dry near a fire, so that the glass is not too hot and will not cause thermal distortion.