Why is my cat connected to the WAN interface of the router, and the other interfaces are connected t

Analyze your wiring method first, you connect the cat to the LAN port is equivalent to connecting a segment of network cable, the other 3 ports can access the Internet, but still need to dial up, and should only be one port dial-up at the same time.

The WAN port can't access the Internet because you haven't dialed up the router, enter the configuration interface of the router, configure your broadband and password, and your 4 LAN ports can directly access the Internet, saving the trouble of dialing.

There must be something wrong with your routing settings.,The cat doesn't want any settings.,Route directly reset and restore to the production settings.,Poke the small hole next to the power supply with a pen.,Press a few more seconds to restore to the production settings.。 Then use the default IP address and username password to enter the router and use the setup wizard there to set the Internet password.

There is also a computer connected to the router to set the number, the gateway and IP should be set according to the situation of the router.

Brother: Isn't yours a campus network? If it is a campus network, it is because it has been upgraded by Telecom, and it can no longer be connected to that WAN interface, because Telecom prevents you from dialing and sharing, so you can only plug in the last three and use them as switches

You connect the cat's cable to the WAN port of the router, and then enter the router for configuration, follow the steps in the manual, and set the password.

Is DHCP off for your router? Use a toothpick to poke the small hole in that REST to restore the factory parameters, and then set it again.

The reason why the optical modem cannot access the Internet when connected to the router WAN port, and can only access the Internet when connected to the LAN port:

1. The optical modem is connected to the LAN port of the router, which is equivalent to giving up the router function and being used as a switch, and the function is the same as that of the LAN port of the optical modem.

2. The WAN port of the optical modem connected to the router cannot be connected to the Internet because usually the WAN port of the optical modem is connected to the WAN port of the router, and the router needs to be set.

3. How to set up the router, connect the LAN port of the router to the computer, get the default management address and default management account password according to the sticker on the router, and log in to the router.

4. Find the WAN port setting, usually the broadband connection is connected by PPPOE, fill in the broadband account password, if there are other ways, please press the direct setting, and click the save button after the setting is completed.

5. After the setting is completed, the basic computer can directly access the Internet.

1. The router has an auto-dialing function, you plug the network cable into the WAN port, and the router will automatically dial the computer, so you don't need to dial up.

And you haven't set up a router, so the router won't automatically connect to the server, and your computer won't be able to connect to the Internet.

The main line is plugged into the WAN port, and the route is equivalent to a small LAN.

If you want to access the Internet on the computer of the Telecom optical fiber connection WAN port, you need to log in to the router settings, and you can access the Internet after you set up the router.

On the back of the router there is a router login account, password, and address. If you can't connect, you can set the computer IP to a segment with the routing address.

2. When you plug in the LAN port, you use the router as a switch, and you can use PPPE dial-up to access the Internet at this time.

To set up the router specifically, you can check the manual, which is quite simple, and it can also be set up according to the routing prompts.

The WAN port on the router is used to connect to the external network (public network), or to connect the equipment of the broadband operator. For example, when the WAN port is connected to the Moden. When the optical brazing is connected to the Internet, the WAN port is used to connect to the optical modem.

When the network cable enters the home to access the Internet, the WAN port is used to connect to the home network cable.

The LAN port on the router is used to connect the devices in the intranet (LAN), mainly to connect computers, switches, printers and other devices. Do not connect the modem, optical modem, or home network cable, otherwise the router will not be able to access the Internet.

Yes, it is normally used in this way, and it is a standard connection.

The network cable plugged into the WAN port of the router cannot be connected to the Internet, but it can be plugged in the LAN port, because the "broadband connection" of the computer desktop is used to access the Internet.

Explanation: 1: The main function of the router is to divide a network cable into several network cables, and then let multiple computers or devices share a network cable at the same time.

This function requires plugging the main network cable from the cat into the WAN port, and then following the instructions on the manual to implement the function.

2: The main network cable that comes out of the cat is plugged into the LAN port, and the computer is also located on the LAN port, at this time, the Internet is accessed through the broadband connection, which only realizes the data exchange function of the router, but does not really realize the main function of sharing a network cable with multiple machines.

Your computer and router are not set up, first of all, your computer disables the broadband connection, turns on the local connection, and sets up to automatically obtain the IP. Then, set the connection mode to PPPoe for the inbound route. Enter the broadband account password, save it, and you can access the Internet after a while.

First, check that your physical wiring is connected correctly;

Second, check if the router is turned on normally;

Thirdly, go to the local connection attributes, select IPv4, and change the manual acquisition to automatically obtain the address;

Finally, go to the router settings interface and see if the settings inside are correct.

Your network layout is rather confusing, and I suggest you take three steps:

1. External network export part.

The line that your network accesses is connected to the WAN port of the device you use to dial up, whether it's a router or a cat.

2. Intranet connection part.

The router and the modem are connected using the LAN port.

3. Other intranet parts.

Direct cable connection to LAN port.

Finally, if you're only using dial-ups, both the cat and the router can do the job, so you can choose one or the other.

If your cat is used for dialing (telecom optical modem can not turn on wifi temporarily), and the router is a wireless router, you can first set the IP address of the wireless router to pay attention to the network segment, it may be, you only need to realize its wireless switch function. The other LAN ports are connected.

If you want to build a wireless LAN. Then it should be like this:

1. Telecom optical fiber access to your optical modem WAN port.

2. The LAN port of your optical modem is connected to the LAN port of the wireless router. (Be sure to change the IP address).

3. Other LAN ports.

It is recommended that you express the question in the future, and you need to explain the model and function of your device as much as possible, so as not to make many people unable to answer.

You're definitely dialing from a computer. The correct connection is that the cat is connected to the WAN port of the wireless router, and then the WAN port is set to the router.

PPPoE dial-in and enter the account number and password. The computer is connected to the LAN port of the router and set to automatically obtain the IP, and you can surf the Internet.

Your way is still to use the computer for dial-up, and the router just acts as a switch. So it's not the right connection.

F460 is ZTE's Class A PON terminal, which has 4 LAN interfaces, namely LAN 1, ITV, LAN 3, and LAN 4You can connect to lan1, lan3, lan4.

Fiber doesn't need dial-up, right? How can there still be cats? Is it fiber-to-the-home exclusive fiber?

Ordinary cats have an opening that can be plugged into a network cable.

ADSL dial-up **Line-modem-routerwan-routelan-to-switch or computer.

If the WAN port of the router cannot connect to the network with the optical modem, you can try the following methods:

1. Reset the router

1.Change the local connection to automatically get an IP address. 2.

When the wireless router is plugged in, do not connect the home network cable first, reset the wireless router (restore the factory), connect the computer to any "LAN" port of the wireless router, enter the setting page, and set it according to the PPPoE (ADSL virtual dialing) method. Then set the SSID, encryption method, and password. Save, restart.

After setting up, connect the home network cable to the "WAN" port of the wireless router. Follow the two steps above.

2. Set it to automatic connection.

The router is a device that sets up a LAN to achieve network sharing, and the general connection and setting methods are as follows: connect the network cable out of the broadband cat to the WAN port of the router, connect each computer to the LAN port of the router, and the IP address of the computer network card is set to be automatically obtained, enter it in the address bar of the computer browser, and specifically check the network parameters obtained by your computer network card, and log in through the IP address of the gateway) Log in to the router, and the general user name and password are admin, Select the WAN port settings, set your broadband account and password to the PPPoE mode (if it is a fixed IP, select the static IP mode), and save and restart.

1.First of all, change the wireless router IP: connect your computer and the router separately, do not connect the optical modem, so that you can enter the settings page, change the router lan port address in the network settings - lan port settings from, to, save, the router is written on the back of the router is, this is no conflict with the default telecom fiber optic modem, you don't need to modify the network connection, cancel the "broadband connection" as the default connection; Click Local Join, Right-Click, Properties, Select:

admin Log in to the router to set up: click the Setup Wizard, enter the wide-net account and password, and select PPPoE mode.

Save to exit. 3. Connect the network cable connected by the optical modem to the WAN port of the router and continue to set the route on the settings page.

3. Reset the router.

If the LAN port of the optical modem is connected to the routing WAN port, you need to set the router to use it normally, please connect the router LAN and the computer separately, and change the IP address of the router to be different from the IP address of the modem! The same IP will conflict, and then enter the router settings interface, (the cat does not turn on the routing function, and the computer needs to dial up to connect the cat to the Internet) Start from the setup wizard, set up the router, select PPPoe dial-up connection, fill in the user name and password, set the wireless password, save and restart. (The cat turns on the routing function, and the computer connects to the cat to go directly to the Internet without dialing) to set the router dynamic IP connection, turn on the routing DHCP function, set the wireless password, save, and restart.

Simple task first use a wired router lan,Set up an Internet account,Generally pppoe,Then connect the WAN port to the cat,Dial through the router page and then set the wireless parameters。

You don't have an account set up in the wireless router, all the plug-in LAN ports are shared by your computer, not the router is boarded, you first connect the router to the computer, and set the parameters inside.

The LAN port of the computer network cable access router.

Set the computer IP according to the manual

Follow the instructions to enter the routing configuration page.

Configure the WAN port adsl according to the manual, select PPPoE, enter the account password, and configure the wireless network SSID encryption mode according to the manual.

Save router settings Restart your router.

That's all I can say, try it yourself, you should be able to do it.

1. Are you sure your cat has a dial-up function? Or whether you dial up the Internet 2, use the router to dial up.

3. Configure the IP of the machine as the management IP of the wireless router and the IP of the network segment, except that the management IP of the wireless router is not special, enter the wireless router for configuration.

4. Configure the account password for dial-up Internet access Enable DHCP and wireless functions for security and wireless encryption.

If you have something, you can q me 466909168

To put it simply, you're mistaken. In other words, you need to reset your routing.

If there is a cat that can not access the Internet by connecting to the Internet, the reason is probably as follows:

1.Your cat has the function of routing, and then connects to a routing WAN port, the function is repeated, and it cannot access the Internet.

2.Your external network cable (cat) is used for community broadband, which has been set up, and it will not work through the route.