Network cable connection issues The connection of the router and the connection of the desktop compu

I want two threads.

The wiring sequence is.

1.Take the modem (cat) out (if you don't have a cat, you can skip looking at the network cable, the connection of the fiber optic cat is the same) and connect the network cable to the network cable interface (WAN port) of different colors on the router

3.To add another computer, repeat 2

Router settings.

1.Enter in the browser (browser, etc.) address bar (where you enter **) or, press enter to confirm, the password is admin (the login address and password are written on the sticker on the back of your router).

2.Find the WAN port settings under the network parameters (this is an example of a TP-Link router, other routers find similar settings).

3.On the page, select the PPPoE mode in the WAN port connection type, then enter the broadband password, save, and restart.

These settings are correct, as long as the computer is connected to the router, you can access the Internet, no need to dial up.

It depends on your room to take the network cable to open the network for you, open it and connect it directly, sorry if you don't open it.

To connect from the router to the desktop computer by plugging in the network cable, you need to log in to the router to set it up. After the setup is completed, the computer that needs to access the Internet should be connected with a network cable or through a wireless router, and use the router to access the Internet.

The steps are as follows:

1.The computer is set to auto-dial.

You need to set the network card of your computer to be automatically acquired and connect it to the router with a network cable.

2.Log in to your router.

Open the browser of the computer (or the mobile terminal is routed through a wireless connection, and also use the browser), enter the default gateway address of the router in the browser", enter the password, and log in. Of course, this information can be viewed on the nameplate at the bottom of the router.

3. Set up the WAN port of the router.

Home broadband users need to set up PPPOE dialing, enter the password given to you by the operator, and click OK.

For leased line users, you need to enter the public network address, subnet mask, default gateway, and DNS provided by the carrier into the static IP address to surf the Internet, and then click OK.

4.Set the wireless name and password.

5.Other. The default LAN gateway and DHCP have been set, and at this point, your setup process is over.

<>2. After the router is connected, you still need to set the parameters of the router to be able to use it normally, and the setting steps are as follows:

1.After the line is connected, open a browser, enter the management address and management password of the router, and then enter the router background (the login address and login password of the specific router can refer to the manual or the label on the back of the router).

<>2.After logging in to the background, select Quick Settings, enter the password applied for from the network service provider, and go directly to the next step after the input is completed;

<>3.Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

4.Confirm it once the input is complete, and then restart the router to take effect.

Yes, the premise is that you need to set the router's Internet access mode and set the parameters, and then the computer is set to be connected to automatically obtain the IP address, and then the computer can connect to the router's network cable to directly access the Internet.

After the router is connected to the network cable, it also needs to be connected to the computer and set up, and the Internet can only be accessed after being connected.

First of all, your cat network cable should be connected to the WAN port of the router, and then the computer should be connected to the LAN port, enter the router and set up your Internet account! Then check the operation of the router**,If the computer can only access QQ,You have to set your local DNS in the attributes of the local connection!

1.Right-click on the properties of the online neighbor.

2.Right-click on My Computer Properties.

3.After opening the properties, click on the advanced --- settings, and in the following customization, we find the item "Use common tasks in folders" and tick the previous one.

4.Then open the Connection Wizard and click Next.

5.Here we choose the first one"Connect to the Internet'Then the next step.

6.Select Set up my connection manually, after which is the next step.

7.Here we select "Connect with a broadband connection that requires a username and password" and then the next step.

8.Here you can click on the next step or enter the name of your broadband connection (you can make your own). After that, the next step.

9.The last broadband connection was built.

First of all, after you connect, look at the taskbar where the two computers have a bad number, there is a difference is the line is different, and then, you look at the connection you choose, broadband connection requires an account and password, if there is no account, the password you can't go up, it is recommended to see what I said!

1. There is basically no problem with the connection.

2. The router needs to be set up to dial up, have you gotten it?

3. Have you tuned the computer IP automatically obtained?

The hardware is connected as shown in the image above, and the router settings are as follows:

Click Setup Wizard in the left rail, click Next;

Click on ADSL Virtual Dialing (PPPoE) and click Next;

Enter the broadband account and password, and click Next.

2. Set the wireless wifi password

There is also an option on the left in the wireless settings, there is an SSID, this is your wireless account, there is a password setting after setting, the password is as complex as possible, the best combination of alphanumeric symbols;

3. Set a login password.

Change the default admin and admin login passwords to prevent someone from breaking the password and rubbing the network to modify the router for you.

Click Save and restart, and you're done.

After the router is set up, the computer is set to automatically obtain the address to access the Internet normally.

1. If the route is with a cat, enter and set up a broadband account and password, 2. If you don't have a cat, you need a cat, and then string a route behind, 1Open the IE bar and enter.

You check the instructions to put the brand is not the same.

Connected to the router, the desktop and notes can be used, indicating that the router is working normally, please check, the first to confirm whether the connection line between the desktop and the router is normal, you can change a network to try, the second local connection is disabled, the third computer does not need to dial, please delete the broadband connection of the desktop. Fourth, please connect the cable normally, check the IP address of the local connection, whether it is, X and the like, if not, check the local connection IP address of the desktop needs to be changed to automatically obtain, fifth, whether the router you use is brand new, whether it is bound to the MAC address, please try to restore the router settings to the default value.

Are you saying that between your desktop and router, there is no network cable when the house is renovated, and you can only use wireless Internet access? That's the case for me. During the renovation, because I was not sure whether the optical fiber could be connected to the TV wall, I simply did not lay a network cable for the desktop, and I wanted to use wireless Internet access.

The router is Cisco's dual-band wireless, which is very fast and stable, but the wireless network card is bought because the 5G one is very expensive. In this way, the desktop is slow to access the Internet. Get a Mercury router when you replace your telco**.

This router is a lot worse than Cisco. However, it is enough to do a secondary router to access the Internet to the desktop computer after doing a bridge. Connect the desktop with a network cable、It also transmits a wifi signal,It can't be turned off、The signal should be slower than the main route、SSID is the same,I can't tell which one is on the phone。

After connecting to the computer, log in to the router in the browser, and there is a setting to automatically bridge the route, which is very simple. At least that's what Mercury 1200r is.

Let's make the problem clear, is there a mistake in setting the gateway?