How to adjust the reverb time on the mixer 30

Which mixer?

Button Echo or Effect Button is the modulation of the microphone reverb.

Button Echo is to control the echo by controlling the reverb, and Effect is the effect level control. To control the echo, you need to turn on the effect send knob of the input channel, which is usually below the aux knob to send the effect signal to the effect bus; Then turn on the effects knob in the total output section, which adjusts the level of the effect signal sent to the main output bus.

Question 1: How to tune the YY reverberation best This depends on your singing skills, if you sing and ventilate the sound is relatively loud, it is recommended to tune it to: **Hall, reverberation to the middle.

If the sound is low, choose the hall and adjust the reverb to the middle. If the voice is mellow and you are satisfied with your singing skills, you can choose the recommendation and turn the reverb to the highest.

Question 2: How to turn on the reverberation when the computer sings If it is a win7 system, click the right mouse button on the gray speaker in the lower right corner of the computer Open the recording device, click the right mouse button in the blank space, select the display hidden device and the display disabled device, stereo mixing, right click to enable, if it is an XP system The gray speaker in the lower right corner of the computer Right click, adjust the audio properties, open the audio, turn on the second recording volume, click the option in the upper left corner of the property, select Stereo mixing, OK, Then put the stereo mix, click on the selection below or unmute, and adjust the volume to half the volume.

Problem 3: The problem of singing reverberation Normal point effect loading. That's already got the parameters ready.

Reverb-sized. Adjust the fader size of the channel. If the reverberation is not very clear, it means that your reverberation effect has not been tuned. Find me to fine-tune it, please let me smoke a pack of cigarettes.

Question 4: How to tune the reverb when the computer sings, you can use this to control the panel with a small yellow speaker.

Question 5: How to tune the mixer to sing well? The upper left selection can not be selected straight-through,There are several options after the drop-down bar,Then adjust the input、Output、The size of the feedback,If you don't need to change the tone, you don't need to change the tone"Don't adjust the volume on the right up。

Question 6: How to tune the reverb tuning in the VST rack to have a good effect? This reverb can also be used very well, the reverb is one person at a time, you can only try it little by little, give you a diagram for you to refer to, and be more patient and adjust it slowly.

Question 7: What is the reverb of karaoke set on the phone? Kugou** has the function of K song, after you finish singing, you can listen to it and think you can send it to the Internet to share it with other listeners.

Question 8: How to tune out the best effect when KTV guests sing? It's hard to say the rest, the ratio of vocals and ** is: 60%: 40%.

Question 9: How to adjust the microphone mixing Right-click the small speaker icon in the lower right corner of the electricity Recording device click to open Right-click on the blank space to display the disabled device Tick on, a stereo mix comes out, right-click the mouse to enable the stereo mix to set the stereo mix as the default device Me.

Question 10: With an independent sound card, how to turn on the reverberation when singing? Select to stereo mix and you're out.

How to debug the reverb of the mixer:

Open the Mixer, click on "View" - "Mixer" in the top menu bar of FL Studio, click on the slot to the right of "Forehand Mixer" and select "Fruity Reeverb" to open the Reverb Effect.

When a vocalizing object emits a sound wave, the sound wave is reflected when it hits the surface of the obstacle through the air. Due to the complexity of the real-world environment, the sound produced by a single source produces a variety of echoes from all directions, and when these sounds are mixed together, they are called reverberation.

Why use reverb:

Reverb makes the sound sound more naturalIn ancient times (the 60s), there was a studio design called the "Dead Room", where you wouldn't hear anything. Its unique design allows the walls to absorb all of the above sounds.

This is arguably the most unnatural situation in nature. You won't be able to tell the way, and your ears will feel weird. You will feel a special and special quiet.

The voice you speak, the song you sing, you can't hear it at all. Even if you stay in this room for a long time, you will pass out. Without reverb, it would be unnatural.

How to tune the mixer reverb ** is as follows:

First, open the mixer and click "View" - "Mixer" on the top menu bar of FL Studio arranger. The second is to click on slot 1 on the right side of "Mixer", and then select "Fruity Reeverb 2" to open the reverb effect.

Computer model: Huawei MagicBook.

System: window10 system.

FL Studio Version:.

First, open the mixer and click on the menu bar "View" at the top of the FL Studio arranger software - Accompaniment Mixer".

The second is to click on slot 1 on the right side of "Mixer", and then select "Fruity Reeverb 2" to open the reverb effect. You can see the parameters from left to right from the filial mask to the reverb effect, the leftmost is high-cut, low-cut, the middle is delay, size, modulation, scattering, speed, bass, attenuation, crossover, damping, and the rightmost is dry, er, wet, and separation.

How to get the best results from the mixer:

1. Sound quality compensation: Sound quality compensation is to use the sound quality compensation device to adjust the center frequency of each frequency band to change the timbre of the sound.

2. Volume adjustment: Before tuning, the dynamic level, frequency characteristics and the proportional relationship between the signals on the scene should be clear about the dynamic level and frequency characteristics of the original sound signal, and it is necessary to listen to it many times and debug it repeatedly, and at the same time, it is necessary to take into account the various conditions and playback effects of future playback.

3. Signal input: From top to bottom is the tweeter XLR socket, receiver input, usually providing conversion power.

4. Plug into the socket: The insertion point is usually located in the input channel of the tuning meter, that is, in front of the signal path, and sometimes directly in the channel input. This dynamic processor insertion point is typically used.

5. Sound control panel: There is a four-segment control panel, here, we can adjust the signal frequency of high, medium and low for each path.