What does it mean when AT P appears on the dashboard of a Toyota overlord car?

1. Exhaust temperature alarm light.

Modern cars have increased the exhaust temperature due to the installation of a three-effect catalytic converter on the exhaust pipe, but too high an exhaust temperature is easy to cause damage to the three-effect catalytic converter, so such cars are equipped with an exhaust temperature alarm device. When the exhaust temperature warning light is lit, the driver should immediately reduce the speed or stop, and after the exhaust temperature drops, the warning light will automatically go off (but after the fuse exhaust temperature warning light is lit, if it is not adjusted or maintained, it will always be on), if the exhaust temperature warning light is not extinguished, the cause should be identified, and then continue to drive after troubleshooting.

2. Brake warning light.

The brake warning light is red and the pattern is a "!" inside a circleSymbol. If the red brake warning light is on, the braking system has the following conditions:

1) The friction plate of the brake is seriously worn;

2) The liquid level of the brake fluid is too low;

3) The parking brake has been tightened (the parking brake switch is closed);

4) Under normal circumstances, if the red brake warning light is lit, the ABS warning light will be lit at the same time, because in the case of the failure of the conventional braking system, ABS can not play its due role.

3. Braking anti-lock warning light.

The anti-lock braking warning light is yellow (or amber) with the word "ABS" inside a circle.

For cars equipped with anti-lock braking system (ABS), when the ignition switch is turned to the "on" position, the ABS warning light on the instrument panel lights up for 3 s 6 s, which is the self-test process of ABS, which is a normal phenomenon. As soon as the self-test process is over, if the ABS is normal, the alarm light will go off. If the ABS warning light continues to light up after the self-test, it means that the ABS ECU has detected a fault that is not conducive to the normal operation of the anti-lock braking system (e.g. the wheel speed sensor signal is not working properly when the vehicle speed exceeds 20 km h), or the EBV (Electronic Brake-Force Distribution) has been switched off.

In this case, if you continue to drive, because the function of the braking system has been affected, the electronic brake force distribution system no longer adjusts the braking force of the rear wheels, and the rear wheels may lock up in advance or flick the tail during braking, so there is a risk of an accident and should be overhauled.

When the vehicle is moving, the ABS warning light flashes or is always on to indicate the different degrees of failure, and the flashing indicates that the fault has been confirmed and stored by the ECU; A solid light indicates a loss of function of ABS. If the braking performance of the car is found to be abnormal, but the ABS warning light is not on, it means that the fault is in the mechanical part and hydraulic parts of the braking system, not in the electronic control system.

What about the overbearing dashboard, showing p it is to prove that you are now hanging in the parking gear, hanging in at means that you are now in the mode of becoming a manual self-integration.

The meaning of automobile instrument AT is manual automatic transmission, also known as manual automatic transmission, that is, manual and automatic integrated transmission.

It is a kind of gearbox based on the automatic transmission, which allows the user to manually increase and decrease the gear. However, in order to avoid damage to the gearbox and the car engine, the system will automatically correct when the user uses unreasonable gears.

While most automatic transmissions have a selectable set of gear ranges, CVT has the ability to continuously change gear ratios. This type of automatic transmission has been used in motorcycles for decades, but its application in automobiles is still relatively limited because of the low engine torque it can withstand.

1. The car instrument AT is a manual automatic gearbox on the car.

2. The car instrument AT means that the car uses the automatic transmission mode during driving.

3. Car instrument AT only exists in cars with automatic transmission.

This is a manual automatic transmission on the car, which means that the automatic transmission mode is currently used, and if you change to manual mode, it will be observed whether it will become MT. Automatic transmission is referred to as AT manual transmission is referred to as MT, this can be optimistic, don't just change the big brother -

Automatic transmission is abbreviated as AT, and manual transmission is abbreviated as MT

p is the position of the current gear lever, which is the parking gear. When you toggle the gear lever, the corresponding gear will be displayed.

Hello in the P file . Hope it helps. If you have any questions, please feel free to ask.

Thank you for your support to Auto Master, your support is our motivation . Have a great trip! [If you have a problem with the car, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】

Hello, indicated for the parking brake. 1. "GB4094 Automobile Control Parts, Indicator Signal Device" stipulates that (P) is red when lit, indicating that the parking brake (hand holder) is in working condition. 2. When parking, make the parking brake work.

When driving, contact the parking brake.

Extended information: 1. When using the parking brake, step on the brake pedal downwards and pull out the parking brake lever upwards. To release the parking brake, press down on the brake pedal, pull the parking brake lever up slightly, press the button on the end of the handle with your thumb, and lower the parking brake lever to its original position.

2. For cars equipped with automatic transmissions, be sure to apply the parking brake first, and then move the gear lever to the "P" (parking) position. When parking on inclined ground, if you shift to the "P" position first and then apply the parking brake, the weight of the vehicle will make it difficult for you to shift out of the "P" (parking) gear when you are ready to start the car.

The P S on the car dashboard should be a warning light for the steering wheel resistance system.

Dear, this question is up to me, it takes a little time to type, please be patient, thank you!

P is the meaning of the gear in the parking gear, if it is not in the position of the gear light, the red P is displayed in other positions of the instrument, it means parking, you see that your handbrake is not loose in place or the brake fluid is insufficient, if it is an electronic handbrake, the system is faulty,

This represents that the parking brake is in the braking state. It is possible that the handbrake is not put or not put in place.

Hello: p Parking brake indicator sign which is the car's handbrake indicator.

The female driver was asked about the circle, and the coach asked: What does the p on the dashboard mean? What do you mean.

The standing system is not put, commonly known as the handbrake!

The handbrake is turned off when parked! That is, the handbrake or footbrake is not let go and released!

The hand brake is not lowered or there is a problem.

p stands for Handbrake Indicator.

The role of the handbrake is to give the car when parking.

A resistance that keeps the car from rolling. The parking brake, i.e. the handbrake or parking gear in an automatic transmission, locks the propeller shaft or the rear wheels. The parking brake is much, much less powerful than the service brake, and it is enough to stop on the slope without slipping.

The electronic parking brake system can integrate the temporary braking function during driving and the long-term braking function after parking, and realize the parking brake technology by electronic control.

The electronic handbrake is a technology that realizes the parking brake by electronic control, and its working principle is the same as that of the mechanical handbrake, which is achieved by the friction generated by the brake disc and the brake pad to control the parking brake, but the control mode has changed from the previous mechanical handbrake lever to an electronic button.

This represents that the parking brake is in the braking state. It is possible that the handbrake is not put or not put in place.

Generally, the gears of automatic transmission vehicles are p, r, n, d, s:

p Parking gear. When the car is parked, the gear selector lever must be pulled into the P position.

rReverse. n Neutral. The n position is equivalent to neutral and can be used when starting, when people are not leaving the vehicle and parking, or when towing a vehicle.

d Forward gear. When driving normally, the gear selector lever is placed in the D position, and the car can automatically shift between the forward gears. D is the most commonly used gear.

S gear is the sport mode of the car ("s is"sport"In the S-gear sports mode, the gearbox can shift gears freely, but the opportunity to change gears is delayed, so that the engine can be maintained at high rpm for a longer time, so that the car can travel at low gear and high rpm for a longer time, and then obtain greater torque output and acceleration. As the car is moving, it pushes the gear knob directly in"S" gear is sufficient, and is usually used on hill climbs and when overtaking speeds quickly.

Automatic transmission cars generally have P, R, N and D gears. The P light indicates that the gear is now in the P mode. The P gear is the parking gear, which is the gear when the ignition is turned off and the car is parked.

The reversing radar switch shows the indicator light of the power supply. If it will be lit, it will work, and if it is not, it will not work.

A wide-bodied model was added to the half-length and short-bodied models at a later date, and a new engine was added. These changes add to its performance. However, the overall feel of the first-generation Prado is still rather stiff and does not meet Toyota's expected sales target.

It is the reversing radar working indicator, no obstacle is green when working, and there are obstacles that will flash, as shown in the following figure:

The specific operation of Toyota's overbearing reversing is as follows:

1. Press the brake pedal of Toyota's domineering.

2. Press the one-button start button of Toyota's domineering to start the engine.

3. Release the hand brake located in front of the armrest box.

4. Put the automatic transmission in R gear and reverse gear.

5. Gently press the accelerator pedal of Toyota's domineering, and the vehicle will move backwards slowly.

It should be the switch of the radar in front.