What does the Sanyo washing machine non stop reality E2 mean

This should be an operational failure, and there is a common display on the manual** failure.

The Sanyo washing machine shows that the EA water level sensor is abnormal.

The Sanyo washing machine shows an EB electrolytic short circuit.

Sanyo washing machine shows EC fuzzy motor no feedback.

Sanyo washing machines show ed electrolytic disconnection.

The Sanyo washing machine shows that the EE heating pipe is abnormal.

Sanyo washing machine shows that the E1 EU does not enter water.

The Sanyo washing machine shows that the EF thermistor is abnormal.

The Sanyo washing machine shows that the EU warm water inlet valve is abnormal.

The Sanyo washing machine shows that the EL heating pipe relay is abnormal.

The Sanyo washing machine shows that the EH computer board does not vibrate.

The Sanyo washing machine shows that the E2 does not drain.

The Sanyo washing machine shows that the E3 is not dehydrated.

The Sanyo washing machine shows whether the E4 washing lid is open or not.

Sanyo washing machine shows whether E51, Child Lock 2, and Washing Upper Cover are open.

The Sanyo washing machine shows that the EC6 is: heating pipe, temperature current insurance, and temperature controller abnormality. a.Heating tube short circuit bAt the beginning of the drying process, when the fuse, heating pipe is broken or the thermostat is off. c.The relay is wired in reverse.

Sanyo inverter washing machine shows E9 and E10

E9** is generally not drained, or no more water enters after the dehydration is completed, and the fault can be caused by two situations:

1.The lid of the washing machine is not closed, which causes the program safety self-test to fail to pass, and generates an automatic alarm and stops running;

2.The drain line is clogged with debris (usually coins, pen cases, and pen caps), resulting in incorrect closure and the washing machine being shut down. It is necessary to disassemble the backsplash of the washing machine, remove the drain pipe, and use a tool to remove the foreign object before it can be recovered.

3.If the high-current lock fails, the computer board needs to be replaced.

I don't know, you don't know if you call the washing machine customer service!

The washing machine shows that the E3 is the washing machine dehydration unbalanced.

Cause: The laundry in the bucket of the washing machine is deflected or the washing machine is tilted.

2. Straighten the washing machine and adjust the balance of the washing machine.

3. If the problem has not been solved, contact the maintenance personnel for maintenance.

Answer: The washing machine shows E3, which means that the switch does not work for 3 consecutive times, which generally belongs to the fault problem of door switch or safety switch and water level sensor, and unbalanced dehydration.

Solution: 1. You can check whether the door switch is normal.

2. Check whether the safety switch is normal.

3. Check whether the water level valve is damaged.

4. Confirm whether the clothing is seriously biased on the side of the dehydration bucket.

The washing machine displays E3: It means that the drainage is overtime (if the water is drained for more than 6 minutes, the alarm can be lifted by opening and closing the door cover once). Troubleshooting:

1. Check to make sure that the drain pipe has been lowered.

2. Check whether the drainage pipe is deformed or twisted.

3. Check whether the drain pipe is unblocked and whether there are any foreign objects blocking the drain pipe.

Maintenance lubrication

In order to make the washing machine run normally and easily for a long time, it is necessary to carry out correct lubrication and maintenance on time, the main places that need to be lubricated are bearings and gears, and the bearings need to be injected with L-TSA22 anti-rust and anti-oxidation lubricating oil with good wear resistance and oxidation stability through the oil injection hole, and generally refueled once a year if used for general mechanical oil.

The gears should be lubricated with No. 2 extreme pressure lithium grease with good adhesion, or zinc dialkyl dithiophosphate with good oiliness with 1% mass content, or MOS2, L-CKC100 medium extreme pressure anti-wear gear oil with 3% mass content for lubrication. The bearings and gears of the spin dryer should be added with L-AN15 and L-AN68 lubricating oil with good oxidation, anti-rust and anti-wear properties every year or half a year.

If a sealed rolling bearing is used, it should be sealed by the bearing factory with a service life of more than 1000 hours, polyurea-based thickened refined petroleum lubricating oil, and No. 2 grease with anti-rust and antioxidant added.

2. Other fault codes are displayed, and the troubleshooting is as follows:

1. E0: The power switch fails to cut off the power supply of the washing machine, and the company's maintenance personnel are requested to repair it;

2. E1: The water inlet is abnormal, the water pressure is too low, the water inlet is too small, and try to increase the water intake;

3. E2: The water is not drained within the specified time, the drain pipe is not put down, or there is a foreign object blocking in the drainage system, put down the drain pipe or remove the blockage.

4. E3: The door cover is not closed, and the door cover of the washing machine is closed;

5. E4: The washing is placed evenly around the barrel on one side;

6. E5: Low voltage protection will be started when the voltage rises, and everything will return to normal;

7. E6: The appointment time is not enough to increase the appointment time;

8. E7: After the appointment is started, the door cover is not closed and the door cover is closed;

9. E8: check whether the water level sensor and its circuit are connected properly if the water level sensor is faulty;

10. E9: Automatic weighing failure check, washing machine transmission system assembly (HU high voltage protection >270V 5V) cut off the power supply, and then use it when the voltage returns to normal.

e3: Unbalanced dehydration.

Solution: Shake the garment back apart and dehydrate again.

There is also a phenomenon that the dehydration front wave wheel will turn a few times to make the already balanced clothes unbalanced, this phenomenon is mostly because the clutch pawl opening is too small, and it should be properly adjusted through its adjustment screw.

Different brands of washing machine failures are not the same If it is a little swan or a beautiful one, you are the door lock problem, and the door is not closed. If you still have the manual, you can take a look at the manual, which has the meaning of the fault **. Hope you are satisfied.

The door cover is not properly covered or the door switch is damaged.

The washing machine shows that the E3 is the washing machine dehydration unbalanced.

Cause: The laundry in the bucket of the washing machine is deflected or the washing machine is tilted.

2. Straighten the washing machine and adjust the balance of the washing machine.

3. If the problem has not been solved, contact the maintenance personnel for maintenance.

Sanyo automatic washing machine shows E2: When draining, the reset water level has not been reached within the specified time.

Causes and solutions for E2 failures:

1. If there is any foreign body blocking at the drainage outlet, it is recommended to dredge the drainage channel.

2. Check whether the drain pipe of the washing machine is blocked, if there are coins or other flocculent substances will also cause the drain pipe to be blocked, dredge it.

3. If the above two points are excluded and cannot be solved, that is, the drainage solenoid valve is faulty, and it is recommended to find Sanyo after-sales service.

Extended information: Common faults and solutions of automatic washing machines:

First, the water does not stop.

1. The general situation is that the valve core of the inlet valve is stuck, and it cannot be reset after being opened by power, resulting in water inlet all the time, and the water inlet valve is replaced first.

2. If the fault is not solved, the problem lies in the water level switch, after a long period of use, the water level switch can stop the water ingress, causing the water ingress not to stop, at this time the water level switch should be replaced.

3. If the pressure pipe is worn and cracked due to a long period of use, or the pressure pipe is in poor contact with the water level switch and the outer barrel air nozzle or disconnected, causing air leakage, it can also lead to more than water ingress, because the computer board is not at the pressure and the water level switch does not act and is misunderstood as the water level is not more than water ingress, at this time, the pressure pipe should be checked for wear and whether there is poor contact or disconnection between the two joints.

4. Due to the long use time, there are foreign objects blocking the air valve mouth, resulting in the pressure cannot be transmitted to the pressure switch.

At this time, the large nut should be unscrewed, and then the inner barrel should be taken out to remove the foreign object blocking the air valve.

5. If everything is invalid, try to replace the computer board, because all actions are controlled by the computer board.

The fault cause of the Sanyo washing machine error**ED2 is the abnormal communication between the main control chip and the inverter driver chip.

Suggested workaround:

1. Check whether the rotation of the empty bucket is blocked, rotate hard to see if the strength is uniform, check whether the eccentricity of the clothes to be washed in the bucket is too large during dehydration, and you can use the empty bucket of rolling pants to test whether the dehydration is normal to judge. After placing the clothes in the bucket again, dehydrate again to confirm that you are smiling.

2. After the sanyo washing machine displays the error **ed2, unplug the power and turn it on again to confirm this fault phenomenon and eliminate the result caused by fault memory. Then replace the computer motherboard, reconfirm the fault phenomenon to see if it is still ed2, and generally replace the motherboard to solve the problem.

Other faults**: E11 is an abnormal water ingress, and the water inlet does not reach the set water level for 20 minutes. E12 is an abnormal drainage, and the drainage does not reach the reset water level for 8 minutes.

U81 is the final dehydration, six consecutive times of non-normal dehydration. U3 is the dehydration eccentricity abnormality, when the final dehydration is carried out, after 3 adjustments, it can still detect that the eccentricity value is greater than the abnormal door lock, and the unlocking is not lifted for three consecutive times, and the lock is not locked for three consecutive times. EF2 is a zero-crossing interrupt signal, and the zero-crossing signal cannot be detected for 8 consecutive seconds.

EH1 is that the motor does not start, and the speed signal is abnormal. No velocity feedback signal was detected for 30 seconds. EH2 is the motor is working abnormally, and the speed does not drop for one minute of shutdown.

EC2 is an abnormal temperature sensor, a short circuit or an open circuit in the temperature sensor. EA1 is a water level sensor anomaly.

Summary. If the Sanyo brand washing machine has E12, it is a drain overtime or no drain failure.

If the Sanyo brand washing machine has E12, it is a drain overtime or no drain failure.

Dear, wait a moment, I'm inquiring for you.

Is the E12 a problem with the machine's drain sensor?

Pro, it is 8 minutes when draining does not reach the reset water level.

Dear, Sanyo brand E12 washing machine failure, there are the following solutions: 1. Check whether the drainage pipe is placed normally, and whether there is a plush blockage and poor drainage in the pipe;

2. Use a multimeter to test whether the resistance between the gray and brown first on CN6 is broken, and confirm whether it is a drainage pump fault;

3. Use the maintenance detection mode to check whether the drain pump is working normally, and whether there is any action sound of the motherboard relay;

4. Test whether the connector is good; 5. Replace the drainage pump and reconfirm the fault phenomenon; 6. Replace the main control board and reconfirm the fault phenomenon.

The machine stops halfway through washing the stove and smiling clothes, which may be the following situation: 1. This kind of situation may be due to the overheating of the washing machine motor caused by the external environment and excessive washing of clothes, and the implied motor thermal protector automatically disconnects the circuit to stop the washing machine.

2. In this case, please unplug the power plug first to see if the ventilation of the sensitive position of the washing machine is not very good, or the ventilation hole at the bottom of the washing machine is blocked.

3. In this case, whether the laundry washed in the washing machine is excessive, if it is excessive, please take out part of the laundry before washing.

4. When the voltage is too high or too low, the washing machine may also have the above situation, and it is necessary to wait for the voltage to be normal before using the washing machine.

The washing machine shows that the E3 is the washing machine is not properly balanced for spinning. Stool dismantling

Cause: The laundry in the bucket of the washing machine is deflected or the washing machine is tilted.

2. Straighten the washing machine and adjust the balance of the washing machine.

3. If the problem has not been solved, contact the maintenance personnel for maintenance.

Other fault codes of the washing machine are displayed, and the troubleshooting is as follows:1. E0: The power switch fails to cut off the power supply of the washing machine, and the company's maintenance personnel are requested to repair it;

2. E1: The water inlet is abnormal, the water pressure is too low, the water inlet is too small, and try to increase the water intake;

3. E2: The water is not drained within the specified time, the drain pipe is not put down, or there is a foreign object blocking in the drainage system, put down the drain pipe or remove the blockage.

4. E3: The door cover is not closed, and the door cover of the washing machine is closed;

5. E4: The washing is placed evenly around the barrel on one side;

6. E5: Low voltage protection will be started when the voltage rises, and everything will return to normal;

7. E6: The appointment time is not enough to increase the appointment time;

8. E7: After the appointment is started, the door cover is not closed and the door cover is closed;

9. E8: check whether the water level sensor and its circuit are connected properly if the water level sensor is faulty;