Has anyone ever disassembled a laptop and how to disassemble a laptop

The first thing you need to do is to let go of static electricity on your body: touch the wall or iron water pipe with your hand.

Then unplug the laptop and remove the battery. Then press the switch of the laptop for 10 seconds to dissipate the power inside the computer. Then it's time to dismantle.

However, the CMOS battery of the notebook is generally wrapped in a layer of yellow plastic and connected to the motherboard with wires, which should be easy to find. My IBM--T21 can be seen with the battery removed.

When disassembling the notebook, you can first find a table to wipe the table surface clean, and arrange the removed screws on the table according to the position on the notebook. That way, when you get up, you know that the screw should go up to that place.

My advice: be careful. Observant. Slow down. If you are not sure, you should still find a maintenance department.

It's not big, as long as you are careful, I'm afraid that the hardware will not fit well!

Just be careful.

A lot of places are jams.

Just don't use brute force.

Of course, you can't help but use force.

Ha ha. The structure of each book is different.

It's okay. Take your time.

Just warp it carefully. If you break the clip, it won't fit tightly.

What brand and what model of notebook are you?,Most of them are clips.,If you're not professional, it's best not to get it yourself.,Just find a place to repair it.,It's ten or twenty yuan of work.。

It is important to look carefully at the structure of the computer before you get started. And then there's the screws. Laptops have a lot of clips, and they are very smart. Don't force it.

It is recommended not to disassemble it yourself, because your LCD monitor requires a professional application.

There are buttons, look for it:

1. Press and hold a small piece of iron on both sides with your hand, as shown below where your fingers are pressed.

2. The small iron pieces are at both ends of the notebook and are symmetrical. Press and hold the small piece of iron described in step 1 with two fingers at the same time, and then press hard at the same time, and the ring will pop open.

3. Remove the paper that needs to be replaced, replace it with new paper, after the paper is placed, just put your hands on both sides of the ring, pinch it gently, and the ring will close.

1. There is also a common notebook with this kind of wire ring, which is slightly worse than the previous one, and it is a little troublesome to change the paper.

2. It is necessary to break the ring at the interface to both sides, and break out a gap of uniform size in the middle.

3. Turn the arc edge of the narrow point of the ring to the place where the paper needs to be replaced, remove the paper that needs to be replaced from the small ring, and put new paper. Then the ring is restored to its original shape.

Loose-leaf notebook is a kind of commonly used stationery, also known as loose-leaf notebook, loose-leaf notepad, composed of cover, binder (or coil), paper, the pages inside the book can be freely removed and added to the notebook.

The biggest difference from ordinary notepads is that loose-leaf books are more flexible to use, the paper can be disassembled, replaced, combined at will, and easy to organize, and users can also DIY according to their own preferences. Loose-leaf books can be used for writing notes, taking notes, and making drafts.

The loose-leaf book is one of the most commonly used stationery items in daily work and study, which is composed of a cover, a binder (or coil), and paper. The biggest difference from ordinary notepads is that loose-leaf books are more flexible to use, the paper can be disassembled, replaced, combined at will, and easy to organize, and users can also DIY according to their own preferences. Loose-leaf books can be used for writing notes, taking notes, and making drafts.

There are many kinds of cover textures for loose-leaf books, including genuine leather, imitation leather, imported color-changing leather, PU leather, artificial leather, PVC, oxford cloth, canvas, nylon cloth, binding cloth, binding paper, special paper, coated paper, etc. The bulk customization of the loose-leaf book can reflect the humanized design, and the cover can be attached to the logo in the form of hot stamping, hot stamping, multi-color anodized aluminum, silk screen printing, leather color printing, four-color offset printing, embroidery, laser engraving, metal nameplate and so on.

Just like ordinary notepads, loose-leaf books can also be printed with a variety of beautiful graphics and advertising slogans on the cover. Accompanied by a colorful cover, it is also one of the factors that people love for loose-leaf books.

The above content reference: loose-leaf encyclopedia.

Step 1: BAI Preparation.

Prepare the tools (a fine Phillips screwdriver, a screwdriver, tweezers, a blade, a soft cloth) and the notebook to be disassembled. dao

Step 2: Remove the battery.

With the back of the laptop facing up, open the battery's retention latch and remove the battery.

Step 3: Remove the back guard.

Disassemble the fixing screws of the two guards on the back of the notebook and remove the guards.

Step 4: Remove the hard drive.

Unplug the hard disk cable and take out the hard disk.

Step 5: Disassemble the NIC.

Gently pull out the network card from the data slot, gently pry open the metal clip of the power cord, and take the network card out.

Step 6: Remove the buckle bar.

With the notebook facing up and the LCD screen on, gently pry open the upper buckle bar of the keyboard and turn it up, and then open the cable connected to the motherboard and take out the buckle.

Step 7: Disassemble the keyboard.

Gently pry the keyboard open and flip it up (be careful not to tear off the cable underneath), disassemble the cable, and remove the keyboard.

Step 8: Disassemble the LCD screen.

Disassemble the two cables between the LCD screen and the motherboard, including power and data, unscrew the display fixing screws, and take the display screen.

Step 9: Disassemble the touchpad.

Gently disassemble the cable connecting the touchpad from the motherboard and remove the main case of the touchpad.

Step 10: Disassemble the optical drive, etc.

Remove the fixing screws and remove the optical drive, heatsink and fan on the back.

Step 11: Disassemble the motherboard.

Unplug the sockets of the cable and the next cable, and then pay attention to the cable below when removing the motherboard, and remove the motherboard and accessories.

Step 12: Disassemble the memory.

Gently push the memory module to the sides to secure the metal clip, the memory module will pop up, and then pull out the memory module.

Step 13: Disassemble the CPU

Release the metal clip of the CPU and pull out the CPU.

The laptop should not be disassembled frequently, and the laptop should not be disassembled frequently. Here's why:

1.Disassembling may damage the computer: Disassembling the computer needs to involve the internal silver balance parts of the computer, if the operation is not done properly or carelessly, it may cause damage to the computer parts.

2.Easy to affect the performance of the computer: Frequent disassembly may lead to problems such as loose cables and poor contact of the Pyri computer, which in turn will affect the performance of the computer, resulting in unstable operation and loud noise.

3.It will lead to the invalidation of the computer warranty: If you damage the computer during the disassembly process, then the warranty of the computer may be invalidated, which will bring unnecessary trouble and cost to your Weifeng repair.

Therefore, if you do not have a special need to replace the hardware, etc., it is recommended not to disassemble the machine frequently. If you need to replace the hardware and other operations, it is recommended to ask a professional computer maintenance personnel to operate to avoid unnecessary losses.

In addition to the few screws visible to the naked eye on the housing, the four rubber pads shown in the diagram can be lifted, and there are a total of four screws inside, and after removing them, a used bank card or card of similar material can be used to protrude through the gap in the housing of the machine. Then slowly walk around the machine, and after the buckle is opened, the shell can be removed.

Laptop disassembly method:

1.Remove the battery first.

Before disassembling the device, first remove the battery, and then press and hold the power button to release the residual power in the motherboard chip.

2.Wipe your hands clean with a toll.

3.Use an anti-static cloth.

Spread an anti-static cloth on the workbench, and it is best to wear anti-static gloves on your hands, which can prevent static electricity from causing electric shock to the motherboard chip or capacitor.

4.Prepare a clean bowl or box.

A clean small bowl or small box is used to store screws, because there are a lot of small screws on the laptop, which are placed in a small bowl or small box after removal to prevent loss. It is best to take a few small bowls or small boxes to sort the removed screws, so that it is easier to know which screw is in which position when installing the machine.

5.Be sure to use ingenuity in the disassembly process.

Nowadays, many notebooks are not completely fixed with screws, and some places are directly stuck together, so be sure to use dexterity to prevent the card head from breaking.

6.Small brushes and blow-dryers.

Be sure to prepare a small brush and a blow dryer, because these two are indispensable and irreplaceable tools in the cleaning process, use a small brush to clean the motherboard and fan, be sure to brush gently, be careful with some small chips, and use a punching bag to clean out the dust in the gaps.