How to start Haier burning energy How to open the burning CD drive of Haier computer C600

Install a nero and burn it

Isn't this thing able to open by itself, and how do you need to open it? Stuck? There's a small hole in it, so you can find a needle or a toothpick and poke it down.

On the basis of being unbearable, it is fortunate that what you buy is Haier's, at least Haier's after-sales service is no worse than that of foreign countries! The second is to disperse, if the bad talk is just a leak in order to go on the Internet, watch a movie, or something, this is expensive! Now ASUS has less than 2,000 netbooks!

I don't know why you chose it in the first place.

1. Pull out the battery and turn it back on.

2. Unplug the SIM card and memory card and turn it back on.

3. Restore factory settings.

4. Rewrite the software.

5. Report for hardware failure.

It is recommended to install a security guard to clean up memory and other information. You can also consider doing a factory reset after backing up useful information. Hope it helps.

You only said that yours is a Combo brand optical drive, but did not say whether it is a optical drive with burning. If you have a CD-ROM and ***-ROM drive, you can only read the disc, if it is CD-RW and ***+r, ***-r, ***+rw, ***-rw, you can burn it.

To solve the problem you said, first figure out whether your current optical drive is good, this is a hardware problem, you can only rely on your own experiment!

First make sure that there is a problem with the burning software, and the burning software is not set up.

If it's okay, maybe it's a hardware problem, wipe the bald head with a tissue and wow.

Hello, thank you for asking the company.

What is the model of your air conditioner, the running light flashes a few times, what is the fault**, different models of different faults** represent different faults, you can record it, refer to the attached fault**, please also call Haier after-sales **4006999999 door-to-door maintenance, thank you!

You are welcome to ask the company questions again.

We wish you a happy work life

Haier air conditioner maintenance failure**:

The cause of the failure of the indoor unit display light.

The power supply is run at a regular time.

Flashing Indoor Ring Temperature Sensor, Flashing Indoor Heat Sensor, Flashing Outdoor Defrost Sensor, Flashing Extinguishing Machine Row.

Gas temperature sensor, flashing off outdoor sensor abnormal, flashing off light press operation abnormal, flashing flash current detection 2Pass.

Current protection action 3Power module temperature too high protection 4Low voltage detection of power modules.

Flashing Flashing Overcurrent Protection Action AC Current Detection, Flashing Flashing Heating When the evaporator temperature rises (above 68 degrees) or indoor wind.

The air volume of the machine is small, the flashing CT disconnection protection is extinguished, the flashing power module is abnormal, the flashing communication is abnormal, and the exhaust pipe is extinguished.

If the temperature exceeds 120 degrees, the flashing voltage is insufficient to explain the reason, and let the user turn off the power for 10-15 minutes and then power on again, and turn off the flash.

Control substrate abnormality, flash off indoor unit EEPROM abnormal, flash outdoor unit EEPROM abnormal.

The use of the recorder needs to install the corresponding software, in addition to the system driver disk, the general brand machine will have another disc with burning software, you need to check your computer instructions and the accompanying CD is not, if there is, then in the "start" menu of the "program", such as nero this software, open it and operate according to the relevant options of the window.

There is also a simple way,XP operating system comes with CDROM disc writing function,Find a blank burning disc and insert it into the recorder,The disc will automatically run and prompt you to have the "Write the file to CD" option,Select the option and press OK,Then drag the file you want to write to CD into this window according to the window option,Click "Next", "OK" and the like to burn。

There are many reasons why the machine can't be turned on, first, the system is damaged, the hard disk is damaged, the notebook can't recognize the hard disk, etc., second, the memory is broken or the memory slot is soldered, and then there is a problem with the motherboard power supply chip, and third, the BGA (north-south bridge, graphics card, network card, etc.) packaging chip virtual soldering damage will be.

Causes the boot screen not to light up. It is recommended that you send it for repair and testing.

It is recommended that you find a reputable and skilled repairer to help you with the repair.

If you have any questions, you can consult me, and I will help you in Beijing.

Hello, thank you for asking the company.

If this problem occurs occasionally, it may be that the system has not started well, if such a problem always occurs, it is recommended to reinstall the system, or call Haier's after-sales ** 4006999999, and let the after-sales master come to check it.

You are welcome to ask the company questions again.

We wish you a happy work life

Mine is710e,This situation needs to be solved by flashing,Go to the after-sales outlets to brush the machine,And then after the version is upgraded,It can be compatible with more software,It won't be like this to start and only display the icon,You can't solve it by flashing the machine package yourself,This phone doesn't leave a back door。 After-sales**, and then find outlets, I hope to help you, thank you!!

You guess the program has been deleted from the system.,You have to re-flash the machine.。

That's the hardware problem of the computer.