How to set up the Swift Wireless Router, how to set up the Swift Router

Connect the computer network card with the LAN port of the router with a network cable and turn on the power of the router; Double-click the IE browser on the computer, enter the IP address of the router default settings page in the address bar, and press Enter; Enter the default username: admin, and the default password:

admin；Click OK. Click Setup Wizard in the left rail, click Next; Click on ADSL Virtual Dialing (PPPoE) and click Next; Enter the broadband, password, and click Next; Click Done. Many friends think that the setting is over here, but in fact, there is still one point that has not been completed.

Because the following settings are not completed, many friends encounter 691 errors in dialing, or can connect to the network, but it will be dropped after a short time. Let's continue the settings: click the MAC address clone menu in the network parameters menu on the left sidebar, click Clone MAC address in the interface that appears, and click Save.

At this point, the router will prompt you to restart the router, click OK to restart the router. After the router restarts, close the Internet Explorer. Connect the WAN port of the router with an incoming network cable, and then connect the computer to the LAN port of the router with a network cable to start surfing the Internet. Note: "Some users have multiple computers at home, but don't know the MAC address of which computer to clone.

You only need to directly connect the cat (or home network cable) to the computer with a network cable, and then dial on the computer, which computer can dial up the Internet, and clone the MAC address of which computer. These processes are done and absolutely ready to use.

It should all be No, there is an underground router Oh.

Just follow the instructions.

Nowadays, families will basically use wireless routing, and the general router setting method is basically the same Let's take the domestic FAST Swift 300M wireless broadband router as an example to introduce the setting method of the Swift wireless router.

tools

A fast router, a computer, and a network cable.

Step 1

Connect to the network where the fast router is located with a network cable or wirelessly. It is recommended to use a wired cable to plug one end into any of the four LAN ports on the FAST300R router, and connect the other end to the computer LAN port

If your computer is not configured with a fixed IP, and there is no problem with the router, the computer should be able to get the IP after a while:

As shown in the figure above, the default gateway is the IP of your router, so we enter this IP in IE (generally you can open the router background management login window:

In the login window, enter the correct background management account and password, and the background management account and password are admin by default;

If you forget this background management account and password, it is generally marked on the back of the router device

If the username and password are correct, the browser will display administrator mode'screen, and a setup wizard page as shown below will pop up (if it doesn't pop up automatically, you can click the "Setup Wizard" on the left side of the administrator mode screen to activate it):

Enter the username and password of the broadband Internet access provided by the ISP in the interface shown in the following figure

SSID number: This is the name of your wireless network;

Mode: The wireless working mode of the router, be sure to use the 11BGN mixed mode.

Turn on the wireless function: Turn on or off the wireless function of the router, and if you cancel this check, turn off the wireless function.

Turn on SSID broadcasting: turn on or off the wireless broadcasting function of the router, if you cancel this tick, then turn off the wireless broadcasting function, computers and other devices need to manually enter this SSID to connect, generally used for confidentiality, it is recommended to turn on, we can give wireless encryption.

You can use a browser to directly open the settings of the Bright side, here to use a computer browser to open the fast router settings interface.

1. Connect the router to the computer, click the network icon in the lower right corner of the computer, and you can see the network that has been connected

3. After pressing the enter key, you can enter the setting interface of the router chatter, enter the management password of the router, and then click the login icon to open the settings interface

How to set up the Fast FW300R wireless router? I used the FW300R wireless router, and the setup method is very similar to the TP-Link wireless router. Here's how to set up the Swift Router I've sorted out, I hope it will help you!

Dial up the Internet

Enter the IP address of the router in the address bar of the browser, and the default is mine'This one is changed. After entering the IP address of the router, press the enter key, and then enter the router and password, the default is admin and click [Login].

After entering the router setup interface, click [Setup Wizard], and click [Next] after entering the setup wizard.

Select the more commonly used [PPPoE (ADSL) Virtual Dialing] and then click [Next]. China Telecom uses PPPO virtual number to access the Internet, and many other operators also use this method.

If your Internet access method is fixed, select [Static IP], and I am using a static IP to surf the Internet.

Enter the ADSL and password provided by the ISP service provider. Click Next

The password here is very important, if there is a slight mistake, it will not be able to go online.

Wi-Fi

Under the wireless settings, click [Basic Settings] -- SSID number and enter a name that you can quickly identify. Once you're done, click Save

Under the wireless settings, click [Wireless Security Settings] -- select [WPA-PSK WPA2-PSK] -- PSK password and enter the wireless password you set. Use this password when using your phone or laptop to connect wirelessly in the future. Finally, click Save