Where is the Audi A6L2 0T coolant pump 2

Coolant for Audi A6L cars.

The pump is located under the car's air intake branch.

If foreign particles are mixed in the coolant, there is a certain chance that the auxiliary coolant pump will be blocked, but in the blocked state, the control program will not actively shut down the auxiliary coolant pump. In severe cases, it can cause the auxiliary coolant pump to overheat, and in extreme cases, it may cause a safety hazard in the engine compartment**.

Check the auxiliary coolant pump of the vehicle, replace the auxiliary coolant pump and upgrade the software if it is blocked; If no blockage occurs, upgrade the engine control unit software. The optimized engine control unit software identifies faults where the auxiliary coolant pump is clogged, shuts them down and alerts them via the EPC lamp.

The coolant pump in Audi cars is located below the intake manifold, below the interface between the engine and transmission.

In the engine block of the Audi A6L, there are many channels for cooling water circulation, which are connected to the coolant pump at the front of the Audi A6L through water pipes to form a water circulation system for the engine of the Audi A6L. Located in the upper water outlet of the Audi A6L engine, it is equipped with an engine coolant pump, which is driven by the car's fan.

There is a thermostat next to the coolant pump of the Audi A6L, and the Audi A6L is turned off when it is just started, and the cooling water does not pass through the water tank, but only circulates in the engine of the Audi A6L.

Hello, the water pump is under the intake branch, behind the generator, look.

Hello, under the timing belt, open the timing cover and you can see it.

Behind the generator, you can see it if you look closely.

Hello friend, the water pump of this car is installed under the intake branch. The interface between the engine and the gearbox is located below the intake manifold pipe. Replacing the pump requires removing the intake manifold.

I hope mine can help you, if you still have any questions please feel free to consult me! BBA, Mercedes-Benz, BMW, Audi Specialty, I wish you a happy life! Fun for the whole family!

Money!

The Audi A6 has a leak in the coolant circulating pump, which is not repairable.

First, this coolant circulating pump is a separate electrical component, and there is no way to disassemble and repair the assembly.

Second, after the decomposition of this circulating pump, it is basically scrapped, so this can only be replaced with new accessories. Shed return.

Third, if the vehicle is still within the warranty period, you can go to the 4S store for free replacement.

The water pump is one of the important components of the cooling system of the automobile engine Minchang, and the function of the water pump is to ensure the circulating flow of the coolant in the cooling system by pressurizing the coolant and accelerating the heat dissipation. As a long-term operating device, the pump will also fail during use.

The position of the oil pump control unit is under the rear long seat, first remove the seat, the co-pilot has a circular plug cover, remove it and there is a square control unit on the right side of the plug cover.

When the plunger rises to the "upper point" and moves downward, the plunger tilting groove will meet the suction inlet again, and the diesel fuel will be sucked into the plunger sleeve, repeating the above action again. Each group of plunger system of in-line fuel injection pump corresponds to a cylinder, and there are 4 groups of plunger systems in 4 cylinders, so the volume is relatively large, and it is mostly used in medium-sized and above cars. For example, diesel engines on buses and large trucks generally use in-line fuel injection pumps.

Under the rear seats. [If you have a problem with the car, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】

The specific operation steps for the installation of the Audi oil pump are as follows:

1. Clean up the Audi oil pump.

2. Take out a small amount of sealant.

Apply to gasket. Splash liquid.

3. Apply sealant on the joint surface of the oil pump.

4. Install the oil pump assembly smoothly on the crankshaft.

Above. Eggplant. <>

5. Tighten all the fixing screws around to complete the installation operation.

The specific operation steps for the installation of the Audi oil pump are as follows:

1. Clean the Audi's oil pump.

2. Take out a small amount of sealant and apply it to the sealing gasket.

3. Apply sealant on the joint surface of the oil pump.

4. Install the oil pump assembly smoothly on the crankshaft.

5. Tighten all the fixing screws around to complete the installation operation.

There is an eye on the balance shaft wheel. There is a hole diagonally above the oil pump casing that can be threaded through with a cross cone. I can just get a point to a balance shaft wheel. When aligned, the two flanges of the balance shaft are flat.