How to deal with the valve connection wire breakage

I'm having the same problem and it's being solved, but I can assume that there is a solution to the problem, and maybe it works.

1. Local heating of the valve (with oil or flame, selected according to the different properties of the valve), low-temperature shrinkage we generally do not have this technology for the time being, and then use a hairpin.

Knock out; (The method is simple, but the technical content is high, and it is easy to damage the method if it is not mastered well, or it cannot be taken out).

2. If the thickness of the wire can be used to cover the inner wire, put on a counterclockwise rotating thread.

bar, then screw on the inner wire, and take out the broken pair wire by tightening the inner wire of the back sleeve; (It's easy, but I don't know if there's a hand tool like this, and it would be great if there were);

3. Find a machine tool and turn it again according to the original thread specifications, and you can naturally remove the wire; (The method is simple, but to have such resources, the cost depends on the relationship between the resources in hand);

4. You can buy a new one; (The simplest and most direct, I think it's a bit wasteful, but the other methods are not economical)

I wish you good luck at six o'clock.

This problem is tricky because there is no special tool to remove the broken section. I don't know what the inner diameter of the wire is, but you can use a screwdriver to punch it in and spin it out.

1. Insert the wire puller into the broken pipe wall. Just plug it in tightly.

2. Clamp the end of the puller with a wrench, and then rotate the puller counterclockwise. It will slowly tighten the large cavity. More and more rolls of sweatshirts.

3. Take a look at the ** below, it has been rotated a little. Difficulty in keeping the rotation on.

4. Finally, turn out the broken part of the pipe.

5. Take it out and rinse it with water.

Summary. The ball valve wire mouth is broken in the pipeline, how to take it out, use the rigid wire inlay or needle inlay to insert the head into the bent wire and force against the broken silk body in the step to rotate the inlay, and there is to use a flat knife to find the break and do counterclockwise rotation of the broken wire head inside. Here are a few ways to do this:

1. Drill a hole in the middle of the broken wire, and use a broken wire extractor or other fixture to take out the broken wire. 2. Make a slot or weld a nut on the broken wire head and unscrew out the broken wire. 3. Drill the broken wire directly.

The ball valve wire mouth is broken in the pipeline, how to take it out.

Hello, I have seen your question, and I am sorting out the answer, please wait a while Oh The ball valve wire mouth is broken in the pipeline, how to take it out, you are pro, use the rigid wire inlay or needle mouth inlay to insert the head into the bent wire, and use the Suizhou force to resist the broken silk body in the step, and turn the inlay in the steps, and use the flat knife to find the fracture and turn the wire head broken in it counterclockwise. Here are a few methods: 1. Drill a hole in the middle of the broken wire, guess the empty cover and use the broken wire extractor or other fixtures to take out the broken wire.

2. Make a slot or weld a nut on the broken wire head and unscrew out the broken wire. 3. Drill the broken wire directly. 4. Use an electric spark to knock off the broken blind wire.

The angle valve wire is broken inside, and the solution is as follows:

1. Close the main gate of the water pipe and let the water flow in the broken water pipe dry.

2. Use a fine-toothed hacksaw blade to cut off the trillions of outer wires that are broken inside.

3. Use the edge of a flat-mouth screwdriver to aim at the pipe wall next to the broken end that has just been sawed out by the saw blade, and then hit the top of the wooden handle of the screwdriver with a hammer, so that the broken head can be easily removed.

4. First wrap the water tape around the stool on the corner valve or faucet wire, you can get a little water to moisten it, and it is better to wrap it, and the winding should be in the counterclockwise direction.

5. Gently rotate the angle valve or faucet wrapped with water tape by hand and install it directly on the inner wire in the wall until it cannot be twisted.

6. Use a movable wrench to tighten the angle valve or faucet, and the strength should be moderate when screwing, not too strong, otherwise it will easily lead to screwing of the wire mouth, which will lead to water leakage. <>