Urgent settings for wireless modems and routing. The computer whiz comes in and helps the rookie!!!

I also changed the wireless route, which is a lot more convenient but the network speed is not very good. The setting is very simple,1,First pull out the line,The cat still wants,A wire of the cat is connected to the network interface of the wireless router,And then the wireless router and the computer are connected to a wire,。 2. Now turn on the computer and start the settings, there should be a manual in the wireless router you bought, follow the operation inside, and there will be no problem.

Tear down the original route,Replace it with a newly bought wireless router,Then enter the routing management page,The method is to connect the computer to the route,Wireless wired can be,Enter the IP address of the route in the browser address bar,Generally or,According to the manual,Use win7 or Vista to view the network topology,You can enter the management page by clicking on the route icon directly,The default username and password is admin,admin,There will be a setup wizard after entering the interface, Depending on your specific situation, take it step by step, and soon you'll be enjoying the fun of wireless!

As you say.

1. The previous wired equipment should be useless.

2. Open the manual of "ZTE Wireless ADSL Router 531B", connect this book to the cat, enter the management interface of the cat according to the instructions, add the password and set the restrictions in it.

The previous one is useless, replace it with a new one and set the following password from the new settings here.

1. Turn on the power of the router and enter it into the management background. Change the IP address of the LAN port to as long as it is not to prevent gateway conflicts and cannot access the Internet), configure the wireless function (wireless account and password), and restart.

2. Link the modem (the modem box has been activated to access the network normally) and the router (connected to the WAN port of the router).

3. It can be used with a mobile device link.

Others should help you! Wireless routers need to be set up before they can be used.

Wireless Router Setup Steps:

1. The WLAN port of the --- wireless router and the LAN port of the wireless router --- the computer.

2. Set the computer IP to "automatically obtain IP".

3. Enter the login information such as the login router, router IP, user and other login information in the computer browser, and put it on the bottom of the router.

5. After logging in to the router, select "Default" or PPPoe for Internet mode.

6. Then enter the Internet account and password.

7. Check the "status bar", if there is a message indicating that the Internet is successfully accessed.

8. Set the wireless network name and password.

Save and exit on it.

Other 1The router is a device that sets up a LAN to achieve network sharing, and the general connection and setting methods are as follows: connect the network cable out of the broadband cat to the WAN port of the router, connect each computer to the LAN port of the router, and the IP address of the computer network card is set to be automatically obtained, enter it in the address bar of the computer browser, and specifically check the network parameters obtained by your computer network card, and log in through the IP address of the gateway) Log in to the router, and the general user name and password are admin, Select the WAN port settings, and set your broadband account and password to the PPPoE mode. 2.

If the laptop uses wireless Internet access, the operation is as follows: right-click the online neighbor - properties - right-click the wireless network connection - view the available wireless network, click your wireless network name in the searched wireless network - connection, and enter your wireless network key for verification, after passing the verification, you can connect to the wireless router to surf the Internet normally; If it is a mobile phone wifi, the same as above, it is also a search for wireless signals and enter the wireless network key to connect and you can use it.

1 The line connection method is as follows: The network cable interface of the modem corresponds to the WAN port connected to the router.

2 All dialing is done by the router. It has nothing to do with cats.

3 The phenomenon that you can't access the Internet. None of us will be able to answer you based on your description.

When this problem occurs, you should make sure that the router is set up correctly (access mode; account and password settings; Other settings, etc.)? And go into the router to observe the hint that he failed. And tell us.

4: The dial-up settings of the router, please tell us the brand of the router. to tell you the interface. In general, you can easily set it up by using the bootstrap interface.

Because your cat in turn routes the function. Dialing is possible. It is completely possible to dial without routing.

I put the network cable that I connected from the cat. You can connect to the LAN port of the router. The WAN port of the router is not used.

The route is used as a switch. （ps。You need to log in to the route first.

Turn the DHCP off. Change the IP address range of the LAN port of the route to prevent it from conflicting with the IP address of the cat. ）

If you must dial in with a router. You can log in to the cat and turn off the routing function of the cat. Enable it in bridge mode. The route is then used to dial the number.

Computer B and C are directly connected to the route with a network cable, and the IP of the local connection is set to be automatically obtained, and nothing else is required.

2: No, unless you change your account password.

3: No, all the broadband is automatically connected by the route, and the three computers are equal and do not interfere with each other.

4: No, the router has remembered the account and password of the Internet, as long as the router and the cat are connected to the power, it will automatically connect to broadband, no need to set anything, it is all automatic.

5: No, there are 4 interfaces on the router, just connect to any computer.

6: If you change the route, you have to re-enter the account and password into the route, because the account and password for surfing the Internet are saved by the route.

All computers are connected to the LAN port of the route, the route can be set once, and then you don't need to set it, the route will always save your setting information, unless you reinitialize the route. In a word, it is only set once, and it is not necessary to set it in the future.