How do you deal with the quality accidents that occur in the mechanical maintenance team

This is a very tricky problem, which was originally intended to be overhauled, and as a result, there was a quality accident.

First of all, from the analysis of the cause of the accident, whether there is any intention of the supervisor, if there is, then it is intentional sabotage, and the punishment will be heavier according to the system.

If it is not deliberate by the supervisor, then it is necessary to consider everyone's feelings, after all, it is for the work, it is recommended to be cautious when dealing with it, conduct a comprehensive analysis of the cause of the accident, the supervisor and the objective should be clearly distinguished, compare the treatment standards, try to deal with it lightly, and do a good job of the relevant personnel, so as to avoid everyone not daring to let go of their hands and feet to work, and even hostile emotions.

If you want to communicate with the experts who are engaged in equipment, it is recommended that you search for the "Equipment People Forum", join the above group of equipment management everyone, and communicate and learn with thousands of equipment management elites from all over the country.

Hehe, it's a bit funny, and the overhaul has an accident.

One is that you may not maintain it properly.

The second is that your maintenance personnel are not professional enough.

In order to improve your professional ability, go to the equipment people forum and take a look!

There's a lot of professional practical knowledge out there!

This should be specifically analyzed the causes of the accident: such as the quality of spare parts, equipment maintenance, if it is a quality problem of spare parts, there are generally maintenance outsourcing manufacturers, but as a workshop acceptance personnel to be assessed for this purpose (that is, inspectors), if it is an installation problem, it is a matter of maintenance personnel. However, if there are no spare parts, but you have to rush to produce, the parts can only be dealt with temporarily, in addition to the problem, on my side is the assessment of the inspection personnel, generally the internal personnel of the workshop to deal with the problem, because it is handed over to the maintenance class to deal with, everyone is the same temporary processing, the final assessment is the inspector, generally the inspector himself handles, so that you are sure, others deal with your own peace of mind?

Summary. Hello, the accidents that are easy to occur in the work of maintenance workers are as follows: in the repair process, the process is complex, the working face is wide, and multiple types of work are crossed. Prone to bruises, smashes, scalds, burns and electric shocks.

Hello maintenance workers work so that the hands are prone to slippage accidents as follows: in the repair process, the process is complex, the working face is wide, and multiple types of work are crossed. It is prone to bruises, smashes, scalding slips, burns and electric shock accidents.

Lifting spreaders (equipment) are often used, such as inverted chains, electric hoists and bridge cranes. To cooperate with the hoisting of the assembly parts in the repair operation, which is prone to the fall of the reeds and injury accidents of biological parts.

In the plant, electric and gas welding and repair operations are prone to electric shock, scalding, arc radiation and fire accidents. During the repair work, Zen Kaga uses electrical equipment to move power tools. Such as:

Air compressors, desktop grinders, bench drills, hand drills, electric wrenches and other electrical equipment are easy to cause injuries and electric shock accidents if they are not properly used and used. If the jack or support stool is used improperly, it is easy to cause the supported car (equipment) to overturn and the operator to be injured.

The following steps can be taken:

1. Immediately cut off the power supply to avoid the expansion of the fault.

2. Record the fault phenomenon and report it to the relevant departments immediately.

3. Do a good job of preparing for fault repair, including contacting relevant personnel to the site, preparing tools, materials and instruments, etc.

Personally, I think that the most important thing as an electrician is safety, and if there is a problem, I think the first thing to do is to look at the accident situation to see if it is necessary to immediately cut off the power of the entire line to ensure safety. After that, the accident points are judged one by one. Avoid bigger security issues.

The first power is off, and the second is to report to the relevant leaders immediately, take the tools and check them step by step, and first make sure that it is not a live work, which is very important.