What are the 9 precautions for the operation of the pipe cutting machine?

Shenzhen Hengfeng main pipe cutting machine, pipe bender, high-speed steel saw blade, alloy saw blade and so on.

The 9 precautions for the operation of the pipe cutting machine are specific:

1. The dust removal device of the pipe cutting machine should be in good condition before cutting.

2 Spindle shifting must be done after stopping. The gears should be fully engaged when changing speeds. When it is found that the machine tool is abnormal, it should be stopped immediately for inspection.

3. When the long pipe is put into the rack and the strapping lead wire is loosened, measures should be taken to prevent the pipe from rolling, impacting, and crushing people.

4. When the machine tool is rotating, no part of the human body shall touch the transmission parts. When operating, the cuffs should be tied well, and it is strictly forbidden to wear gloves to work. The human head should deviate from the direction of cutting.

5. When using a grinding wheel pipe cutting machine, check whether the grinding wheel is defective, cracked, damp, and whether the power cord is reliable in advance.

6. When the pipe cutter cuts the pipe head, it is necessary to prevent the pipe head from flying out and hurting people.

7. Before cutting, the pipe cutter should adjust the cutter and clamp the working object. The length of the clamping part shall not be less than 50 mm. The parking baffle should be fixed, and the work can only be carried out after the sequence of clamping, loosening, forward, backward and so on.

8. No person should stand in the direction of the workpiece in and out.

9. When changing tools, measuring workpieces, lubricating, and cleaning the pipe head, it must be stopped.

Thank you for the publicity, the pipe cutting machine chooses a professional manufacturer! Lekai Machinery.

Hello, today, Hewang electromechanical automatic pipe cutting machine manufacturers will explain to you the general faults and solutions of automatic pipe cutting machines! 1. Turn on the power switch, the panel has no display and the light is on, the fuse may be damaged, please replace the fuse that meets the specifications. Second, the cutter has been cutting, no feeding, the near switch to close to the screw, but can not touch each other, if the pin jujube pin is still not good, may be the proximity switch damage, may also be the computer box damage, three, cut out the length of the material is not the same:

1.The pressure on the upper roller is not small, adjust the pressure nut to increase the pressure. 2.

The feeding motor fixing screw is loose, tighten the screw. 3.When the jackscrew of the lower roller roller or the jackwire of the feeding motor pulley is loose, the jackscrew is locked.

4.When cutting more than two at the same time, and the length of the two cuts is not the same, adjust the pressure on both sides of the upper roller to make the length of the two cuts equal. 5.

If the feeding motor feeds the material without moving smoothly, it is a failure of the drive box, please replace the good drive box.

Summary. Pro, it may be that the laser focus point of the laser tube cutting machine is accurately positioned left and right, and it can be corrected before application; It may be caused by the insufficient power of the laser tube cutting machine, check whether the laser generator is working normally; It is also possible that the acceleration of laser cutting of the laser pipe cutting machine is very slow, and the cutting line rate needs to be expanded at this time.

Pro, it may be that the laser of the laser pipe cutting machine is embedded in the right and left precise positioning of the focus of the puncture, and it can be known that the correction can be carried out first and then the bending defect can be applied; It may be caused by the insufficient power of the laser tube cutting machine, check whether the laser generator is working normally; It is also possible that the acceleration of laser cutting of the laser pipe cutting machine is very slow, and the cutting line rate needs to be expanded at this time.

The common root cause is that the laser nozzle must be replaced due to the mismatch between the model and thickness of the laser nozzle and the thickness of the pipe fittings. It is also possible that the angular speed of the laser cutting machine must be reduced due to the fact that the laser cutting speed set by the laser tube waiting machine is too fast.

Whether the machinery and equipment that must be produced are in the scope of production and processing, such as pipe fittings, specifications, thickness, etc. 2.Whether the processing technology of the laser cutting machine can meet the requirements of safe operation.

Summary. 1.First, turn on the pipe cutter, put the tube you want to cut into the tube cutter, and tighten the tube with screws to make sure it doesn't come loose or slip.

2.Then, open the main side of the tube cutter to check if the tube you want to cut is normal, and if not, readjust the tube. 3.

Next, start the tube cutter and adjust the depth of the cutter head so that the cutter can go deep to the desired depth. 4.At this time, press the start button, the pipe cutter starts to rotate, and the pliers and cutter head cut at both ends of the tube.

5.Finally, stop the pipe cutter, check if there is a notch in the cut pipe, if there is, readjust the cutter head to adjust the depth and run again.

I'm still a little confused, can you be more detailed?

1.First of all, turn on the pipe cutter, put the tube to be cut into the pipe cutter pin, tighten the tube with screws, and make sure it does not loosen or slip and collapse. 2.

Then, open the main side of the tube cutter to check if the tube you want to cut is normal, and if not, readjust the tube. 3.Next, start the tube cutter and adjust the depth of the cutter head so that the cutter can go deep to the desired depth.

4.At this time, press the start button, the pipe cutter starts to rotate, and the pliers and cutter head cut at both ends of the tube. 5.

Finally, stop the pipe cutter, check if there is a notch in the cut pipe, if there is, readjust the cutter head to adjust the depth and run again.

To choose the right model according to the size of the pipe, you can come to our company if you have time, there are semi-automatic and fully automatic pipe cutting machines.

1.Check before powering on.

Check whether the saw blade is in good condition, and replace it when there are gaps and cracks.

According to the specifications of the high-pressure hose, replace the corresponding positioning pin and guide sleeve.

2.Procedure.

Plug in the power and start the motor.

Thread the cut high-pressure hose into the changed guide sleeve, pull the knife-shaped handle to drive the hose into the saw blade, the hose is cut off, and when the slide plate is reset, it is pulled back to its original position by two tension springs.

Insert the inner hole of the cut hose into the positioning pin, and when the saw blade rotates, a slit is cut at the place where the rubber is ready to be peeled, so as to ensure that the hose is stripped and the glue is cut off to produce a good glue breaking effect.

After work, the power supply must be cut off.