The navigator did not respond to what was the problem

Answer: This situation occurs after you click "Factory Reset". Before you click on the navigation to see 5 or 3 maps because we tested the machine before sending it out and set it up for you. After you do a factory reset, there is no navigation path.

Solution: Select: "Settings", go to the settings page, and then turn the page.

After turning the page, you see the words "Navigation Path".

Click on "Navigation Path" to enter.

A rectangle will appear in the middle, and you can click on the white arrow behind the rectangle or navigate the path to enter it.

If it's an electric white arrow, then go straight to the SD card. If it is the word dot navigation path, then sdmmc will appear, and you need to double-click sdmmc to enter the sd card.

Then several files will appear, no matter how many they appear, just double-click on the last file (from left to right).

You'll be taken back to the Navigation Paths page, and the path will appear in the rectangle below.

Click on one of the two charts in the upper right corner of the machine to save it.

Complete the navigation path setup.

At this time, you are back to the main interface, click on GPS navigation, and the normal map display will appear.

Suggestion: Don't press "Factory Reset" lightly.

This kind of problem is very common,The solution is to re**install the package,Clean up the memory,Of course,If you are troublesome,You can also**A Tencent map is also good,I have basically no problem with him,The route is more accurate,I think this is the most practical,The most important thing to drive is the route,Everything else is nothing,And then it is very difficult to take a taxi when you don't drive occasionally,You can also take a taxi with a map,It will be easy to meet daily needs。

Hope to solve your problem and give a kind upgrade that needs yours! Thank you!

Hello, what is the reason why my navigator can't connect to the Internet?

Hello What is the reason why my navigator can't connect to the network, hello pro-car navigation chain Ling Fu shows that there may be the following reasons: 1. The navigation has no wifi function, if any. Please check if it is a match.

If none of the above problems can be solved, please consult the merchant's customer service to find a solution. I hope I can help you, I wish you a happy life and smooth work!

Hello, the car navigation button failure first rule out whether it is a problem with the system, first reset and restore the factory settings to see. It's not good, it's that the key itself is not in good contact or the corresponding module is faulty. It needs to be sent for repair.

There are also supplements that you don't understand to help you. What's going on if the car navigation buttons don't respond? I'm afraid it's not that simple.

You don't know, more than a month ago, the group of Shadow Cat Clan women escorted by the Stone Hall Master were robbed, and more than 20 people, including the Stone Hall Master, disappeared, and their whereabouts are still unknown, but now it seems that it is very likely to be related to the recent incident. The stone hall master is second only to you and me in the middle stage of the Yuan Infant cultivation, and he has not even been able to escape from the Yuan Infant, which shows that the person who came is not good. The blue-robed middle-aged man said with a deep groan.

There is such a thing! It seems that the strength of the other party is not inferior to that of the eldest brother, I can't say it, I have to alarm the Heavenly Ghost Sect this time. The scarred man gasped and said.

At this moment, there was a "click" sound from the depths of the main hall, and the surface of the stone door was bloody, and then it opened from both sides, and a white-robed man walked out slowly.

The car navigation screen touch screen does not move, you can restart the navigation, restore the factory, press the restart function, repair, etc.

1. Restart the navigation and restore it to the factory

The restart function key is a small built-in button that is available on all GPS navigators at the back or side of the machine.

2. Press the restart function

After pressing the restart function button, see if the display responds, and if there is a response, go to the settings to correct the display, and it will be good after correction.

3. Maintenance

After restarting, the display screen does not respond, charge the battery for a long time, charge the battery holder that can be taken down, and charge the battery that can't be held with wire. If it's not good, it's only repair. In addition, check whether the port is loose, whether the car is too damp, and the temperature is too high are all caused by the failure of navigation.

The cause of the car's navigation screen's touch screen malfunctioning

1. The service life of the screen expires.

2. There is a problem with the resistive screen.

3. There is a film on the top of the screen, which causes the film to be glued to the surface of the screen.

4. The screen itself is malfunctioning. If these are the cases, there are many factors involved, such as the touch screen may be damaged, the interface may be loose, the route may be faulty, and so on. If the car touch screen fails, you can go to the 4S shop or find a professional repair shop to overhaul or replace the touch screen of the car.

Causes and solutions:

1. When clicking on the screen of the navigator, the fingers are stained with conductive media such as oil and sweat, which will form a conductive layer on the screen, which will cause the screen to be unresponsive.

2. The temperature of the navigation instrument surface is too high, and when the temperature reaches 40 degrees Celsius, it will cause the capacitive screen to drift.

3. The high frequency of the car touch screen leads to inaccurate touch, so the screen does not respond: Method: Re-open the car navigation after closing, and then recalibrate it.

1. Whether the resistive screen is used in the car navigation touch screen, because the sensitivity of the resistive screen is not accurate enough.

2. For the problem of high frequency touch control for the car touch screen, first restart the car navigation, and then detect whether the car touch screen motherboard is damaged.

3. Find the restart (factory reset) button on the machine, which is a small built-in button, which can be found on the back or side of the machine.

4. After the button is restarted, see if the screen has a response, and if there is a response, hurry up and calibrate the screen in the settings, and it will be fine after calibration.

5. If the screen does not respond after restarting, if the battery can be taken down, then charge the battery separately and be charged with the cradle; If the battery can't be taken off, charge it with a wire, and the charging time must be long; If it doesn't work, then it can only be repaired.

It may be out of power, try charging it overnight, and if it doesn't respond when you connect the external power supply, you can only flash it.

The car navigation system can't be turned on:

Black screen on startup: In most cases, the battery is exhausted, many people have a habit of using the navigator is, in order to facilitate the use of the navigator, often do not turn off, the use is to let him default standby, which is convenient to open the speed of the navigator, but the navigator is in the standby state, it will slowly consume the power of the battery, and the power will not be turned on naturally.

After powering on, the screen is powered on, but the screen stays on the boot screen or the white screen is not messed up, and the book can enter the system.

This situation generally occurs in people with strong hands-on ability, most of the situations in a navigator are caused by the failure of the brush APP or OS system, it will become the so-called brick of the fierce hidden, if you have a strong branch on hand to accompany the hall to make the software of the machine, just brush the machine again, if not, send it to the merchant to brush it.

The reset button is usually on the screen and the main unit, with a small round hole or a small button. You take a closer look. Take a paper clip and poke it out.

1. First of all, we must detect the software, to put it bluntly, the win ce system software is not loaded too much during use, resulting in system failure, and the general navigation repair shop can repair it.

2. The drive of the machine itself; This requires the manufacturer's software to be able to reinstall the machine system;

3. Hardware (that is, the touch screen is really broken).