Can I still install a wireless router for network cable tapping?

Yes, but you must know how the host is online, otherwise you may not be able to configure routing. 1. If the landlord is a cat plus switch mode, then you must know the dial-up account number and password; 2. If the landlord is a fixed IP, then you must know his IP, subnet mask, gateway and DNS server address; 3. If the landlord has used a router, enter the address in the landlord's routing address pool (if the landlord has turned on the dynamic allocation of LAN ports, your route can be obtained automatically), and the gateway should enter the landlord's router address, and the DNS server should fill in the server address of the residential area, and note that your router address (the default address is the IP address labeled on the back of the router) must not be located in the same network segment as the landlord's, that is, if the landlord is, Yours is going to change to or the third digit is 2 254 for the other number.

Absolutely.

This one is very simple, you connect your network cable to your computer first to see what the IP address is? Whether it is from the landlord is also routed, if so, the IP addresses of the two routers cannot be the same, just change the address of a LAN port, and then enter your router and set the WAN port to a dynamic IP, just do it.

Don't be so troublesome, just get a T Plink wireless AP, and you can use it when you connect it to hundreds of pieces.

Yes, there are two ways:

Method 1: 1. First connect the LAN port of the wireless router with your own computer, log in to the wireless router for configuration, turn on the wireless security mode, click "WAN port settings", set the IP address of the wireless router to the IP address inside your organization, turn on the DHCP function (it is enabled by default), and save;

Method 2: 1. Connect the LAN port of the wireless router with your own computer, log in to the wireless router for configuration, turn on the wireless security mode, and then click "LAN port settings", set the IP address of the wireless router to the IP address of your organization, turn off the DHCP function, and save;

2. Connect the network cable of the unit to the LAN port of the wireless router, and the laptop must be configured with the company's internal IP address to access the Internet.

Two different methods, in fact, the first is the normal use of the wireless router, the second method is to use the wireless router as a wireless switch (note that the interface of the network cable is different between the two methods), and then tell you the advantages and disadvantages, the disadvantage of method one is that the computer of the same workgroup outside can not access the computer connected to the wireless router, because it is natted, but the computer connected to the wireless router can access the external computer of the same workgroup, and the second method can access each other.

A while ago, I led the inspection unit, and I used two TP-Link routers (model: TWR845N, about 180 yuan), one connected to the external network (with wireless routing mode), and one connected to the internal network (with wireless switching mode), all of which can be.

Yes, but when you install the "secondary" route, pay attention to whether there are restrictions on the front, such as binding the MAC to specify the IP, and your route LAN IP must not conflict with the front.

It can be installed,When you buy it, pay attention to buy one that supports wireless AP mode.,The other thing is like what I said upstairs.,Pay attention to whether there will be restrictions and IP address conflicts on the host side.。

You can use a wireless router again, you can set a fixed Internet IP in the wireless, such as: Specifically, depending on your company's ability to access the Internet normally, the IP segment of the computer.

1. You can connect to a wireless router, but you have to set it up. Set up the wireless router on your computer separately, log in to the router, set the wireless password, and then turn off DHCP. And save.

2. Connect the network cable to the LAN port of the wireless router, and then split the line from the LAN port to the computer.

OK.

The second router is set up and you're good to go. Enter the second router, select Dynamic Acquisition as Internet access, then set the wireless name and password, change the IP address of the router, replace it with or directly turn off the DHCP address of the router, and then save and restart the router.

Plug the network cable separated from the main router into the LAN port of the second wireless router, remember not to plug in the WAN port, otherwise there will be no network.

Yes, hello, have your doubts been solved?

The network cable separated from the router can also be connected to the wireless router. The wireless router you connect to requires a different setup. Here the first router is described as the primary router and the second router is described as the secondary router.

The main router is set up normally, and the specific steps of the secondary router are explained.

1. The secondary router (the second) should not be connected to the main router (the first one) first, the LAN port of the secondary router is connected to the computer separately, the computer opens the browser, enters the address of the router, and then enters.

2. Enter the administrator password and press OK, if it is a new router, then you need to create the administrator password.

3. Click on the network parameters on the left, click on the LAN port settings, modify the original IP address, click Save, the router will display the restart taking effect, after the restart, you need to pay attention to the address that needs to be entered to log in to this router.

4. Enter the router management interface again, click DHCP server, click Disable, and click Save (because you need to connect to the main router later, as long as the main router has the DHCP server turned on).

5. Click Wireless Settings, enter the SSID name, click WPA-PSK WPA2=PSK, set the PSK password, and click Next.

6. After the router is set, click Save, then restart the router, and finally connect the network cable from the LAN port of the main router to the LAN port of the secondary router (note that the above steps can only be connected to the LAN port in the LAN port).

After all the settings and connections are completed, the login address of the primary router and the login address of the secondary router are all set, and the connected devices can log in to the two wireless routers separately through the browser.

The network cable separated from the router can also be connected to the wireless router, as long as the IP of the second router is set to be different from the main router, or the DHCP address can be turned off directly.

Here's how:

1. Enter the router to be reconnected and select Auto Configuration;

2. Set the wireless name and password.

3. Change the IP of the router to be different from the original router;

Or go directly to DHCP address management and close the DHCP address.

After the network cable is split, connect to the wireless router Setup method: Set up a level 2 route.

1. How to connect two routers.

1. There is a cat (modem): cat (modem) - router 1wan port; Router 1LAN port --- router 2WAN port; The 2lan port of the router --- the computer.

2. No modem: network cable --- router 1WAN port; Router 1LAN port --- router 2WAN port; The 2lan port of the router --- the computer.

Second, the setting method.

Before setting, disconnect the WAN port cable of the second router and plug it in after the setting is complete.

1. Set the IP segment of the second router.

After restarting the router, the address to enter the router is.

2. Set up a second router to access the Internet.

Check the IP details of the computer connected to the first router. (win+r--input, cmd--input:ipconfig all [remember: ip, mask, gateway, dns]).

Set it on the second router, and select Static IP in the Setup Wizard. Enter the IP that the 1st router does not use, and the others: mask, gateway, DNS settings are the same.

Restart your router once it's set up.

3. After restarting the router, the setting is completed, and the line of the 2WAN port of the router is reconnected to make the router 2 network normal.

Turn on the router's wireless function].

1. Enter the router:

Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name, password, (the default is generally admin).

2. Select Wireless Settings --- Basic Settings.

3. Check [Turn on wireless function] and click Save.

Set wifi password].

1. Enter the router:

Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name, password, (the default is generally admin).

2. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.

It can be connected, but the signal may be slightly weaker, and the speed is not very fast, I tried, pay attention to the wireless routing and the previous router IP address do not repeat.

The shunt cable is directly connected to the wireless router, and then connect a network cable to your computer, as long as the wireless router is set up, your mobile phone can receive the wireless signal.

You can use the unlimited router directly without the need for additional equipment.

Method 1: Method 2:

Or you can use a wireless router with a network cable that splits from a higher-level router in the following ways:

1. The host is connected to the LAN port of the wireless router, and after logging in, first modify its LAN port address, which is not the same network segment as the higher-level router, for example, the higher-level LAN port is, then the lower-level can be set to, and the router will restart after modification;

2. After restarting, log in to the wireless router with the new address, set its Internet access mode to dynamic IP, then turn on the wireless function, set the encryption method and password;

3. Finally, connect the WAN port of the wireless router with the LAN port of the higher-level router with a network cable.

Yes, plug it in and use it, no need to log in to the account password.

If there is a remaining LAN port, it is possible.

The route is divided, generally one in and four out, and you can divide it as you want. You can divide as much as you want.

The network cable separated from the router can be connected to a wireless router.

If you can't access the Internet, first troubleshoot the network cable, and you can use a network line tester to test the connection of the network cable.

Because, it shows that the local connection is on, but you can't access the Internet, and the wifi of the mobile phone shows that it's connected, but you can't access the Internet. This only shows that the router is working. It cannot reflect the connection status of the network cable.

Secondly, if two routers are both on the same network segment and use the same login address, it will cause conflicts.

Solution: 1. To test the network cable, you can use the network line tester. Or on the wireless router, connect to the computer to test whether the network cable is faulty.

2. Turn off the DHCP function on the wireless router and do not assign addresses to the wireless router. Connect to the original router, which assigns an IP address.

1. After the wireless router is plugged in, the computer uses a network cable to connect to any LAN port of the wireless router. Do not connect the wireless router to the original router at this time. Open your computer browser and enter it in the address bar.

On the management page of the wireless router, enter the login account and password of the wireless router to log in.

2. Enter the wireless router settings interface, in the "Network Settings" on the left, "Router IP Address" is changed to "Done", and the wireless router will automatically restart. For the sake of memory convenience, it can also be changed.

Change the address of the wireless router to so as not to conflict with the original router, and the address of the wireless router will be logged in in the future. In this way, you can continue to use the original router by connecting it to the original router.

3. Reuse, log in to the wireless router interface, click on the left menu "Internet", and select "Dynamic IP" on the right. Because it is connected to the original router, the original router needs to assign an IP address to the second router.

4. In "Wireless Settings", select "Enable DHCP Server" and check Cancel. The router reboots after saving. Connect the wireless router under the original router and you can surf the Internet.

Yes, it's a little troublesome, and it is recommended to find someone who understands it to help you operate. And your first one is also a wireless router, can't you directly connect to mobile phones and laptops, why do you need to get another one?

Yes, no problem.

I've tried it myself, but I'm like this!

One of them: connect a cable with Internet access to the upper floor!

Second: the upstairs router, to modify the gateway to not be the same as the original third: the upstairs router can be set to a fixed IP Internet mode, for example, set a different SSID from the downstairs router

The above premise is a dlink wireless router, if it is tlink, it should be or 100 or 128