Can FlashMail connect to a wireless router? How to pick up?

To establish a wireless connection, click on the network icon.

Click to open the tethering hub.

Click Attendance to manage Wi-Fi.

2 .Click Add.

3 .Create a temporary network is selected here.

5 .Select WEP as the security type (based on your needs).

6 .The key is the password to connect to the wireless network.

7.Tick Save this network and go all the way to the next step.

8 .Just close it here.

Flash is a one-to-one connection, can not be shared, can not be moved, flash access mode is optical fiber, so it is not convenient to move to the home use, the home is basically a network cable.

Mine is wireless. You connect the port line to the LAN port, don't connect it to the WAN port, go to your router and put DHCP (that is, the IP is automatically assigned, how to turn it off, it depends on your router, you can check it online. That's how I changed mine, and now it's very good!

I can't connect, JS has made a limit, and I can only go on one-on-one.

Open UnionPay. 2 10 Click "Scan". 3 10 can scan the code to pay.

4 10 Click on "Payment Code". 5 10 can allow the other party to scan the code to pay. 6 10 Click on "Card Management".

7 10 You can see the balance and transaction information of the bound bank card. 8 10 Click on "Collect Code". 9 10 can be collected.

Ladies and gentlemen, are you suffering from the recent upgrade of telecommunications, so you can't use the router to access the Internet?Are students still bored with not being able to access the Internet? Are you outraged by the disruptive behavior of telecommunications?

Are you still hesitating to reopen the port? Are you still thinking about how to deal with your router?After a nameless person who did not want to be named, he tested day and night, and finally after intense debugging, he completed the complete cracking of the flash dial-up can not use the router to distribute the IP.

Use this program to dial up the broadband router, and the users below the dial-up router can share it freely.

This software is only used when dialing, you can exit after dialing, as long as the router does not lose power, dial once a day, and the computer is shut down without redialing.

Now it supports routers such as D-Link, Tenda, TPLim, Mercury, and FAST, and all routers on the market that use ARM9 processors (more than 95% share).

Please restore the router to factory settings before using it, and restart the router before dialing up each time.

How to configure the new router for the first time:

1.The router is connected to the network.

Connect the network cable to the WAN port of the router, and use the network cable to connect the computer to any LAN port of the router. When the LAN port flashes when the computer is turned on, it means that the computer has successfully established communication with the router.

2.The system is connected to the router.

Turn on the wifi of the computer, search for the default wifi name of the router (the nameplate on the back of the router is written), and connect to the wifi network. The first time you use the router, you generally don't need to enter the wifi password.

3.Go to the gateway page.

Open a computer browser and enter the gateway IP address of the nameplate on the back of the router (generally, enter the gateway configuration interface. (This interface will pop up automatically for new routes).

4.Set up a way to access the Internet.

Go to the WAN port settings in Advanced settings. If the broadband service requires dial-up, select PPPoE dial-up, otherwise you can choose DHCP to get automatically. To dial up PPPoE, enter the broadband password, and select Automatic connection as the connection mode.

If DHCP is automatically obtained, you do not need to enter this field.

5.Set the wifi name and password.

Go to Wireless Security in the Wireless Settings and select WPA2-PSK mode for Security Mode. Select AES for WPA encryption rule. Set up a wireless network key. The router will automatically restart after setting, please enter a new wifi password to connect.

6.The configuration is complete and you can enjoy the network.

If it doesn't work at all, my computer won't work.

If your router is tested in a friend's dormitory and can be used normally, then it is definitely not a routing problem, and the computer can also be used, then it may be a line problem. I estimate that the wiring problems in your dormitory, 1, poor contact, 2, school restrictions.

How to set up a router with flash:

Home Network Environment Cabling]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

1. Set up the router first: plug in the router and enter it in the address bar of the desktop. Look at the router that should have a username and password written on it), after going in, set the wired option first, which will let you enter your broadband and password, and then OK, so that the wired is set; Then set the wireless option, when setting up the wireless, it will ask you to name the wireless network, you give a name, set a password, OK, the wireless is set.

2. Set up the notebook again: right-click the network neighbor - attribute - local connection - attribute - double-click the inter protocol, and tick the automatically obtained IP address; Right-click on my computer - properties - hardware - device manager - network adapter - there are at least two or more network card devices in it, you turn all of them on, (that is, there is no red eight-pronged line), in this way, a wireless reception icon will appear in the lower right corner of the computer, you click on it, search for the name of the wireless network you built, and go in.

1) Generally, it is.

However, it is subject to the instructions.

2) Input. admin

Password. admin

3) Click"Next"

4) Select the network you are using, if you are in Telecom.

Netcom application.

Select Dial-up Internet access. If you use the school net.

Select the static IP one

5) If you choose a static IP

Then put the address where you apply.

Gateway. Copy it again.

That's it: if you're telecom networkcom, it's simpler to apply you to the password.

OK6) Finally.

Online neighbors.

Local connection. Put the IP

Set it to get it automatically.

And then. Reboot.

Routing. It's ready to go!