How to set up the TL WR840N router?

The wireless router TP-LINK840N can be set up as follows:

1. Plug the network cable (bus) into the WAN port of the TP-Link wireless router, plug one end into any LAN port of the TP-Link wireless router and connect the computer network card at the other end, and turn on the power supply of the router.

3. Then enter admin, the default account name and password are the same (there is also a prompt for the original data on the back of the router) to confirm.

4. After entering the TP-Link wireless router setting interface, select the Internet access method according to the setup wizard (different broadband selection methods are also different), and enter the Internet access and password.

5. Save, continue to set the wireless key, and then you can surf the Internet normally.

6. If it is abnormal, you may wish to click the reset button of the TP-Link wireless router and set the router again.

Here's how to set up your wireless router:

1. The broadband bus (the network cable from the cat) connects to the WAN port of the router.

2. Connect one end of the network cable to any LAN port of the router, and connect the other end to the computer, and start the computer and router equipment;

3. After starting the device, open the browser and enter the router address in the address bar (the reverse side of the router can be viewed) to enter the wireless router settings.

Interface. 4. An account and password for logging in to the router appear in the settings interface, and enter the default account admin

5. Set up step by step according to the setup wizard and select the Internet mode, usually ADSL users choose the first PPPoE, if you use other networks.

The service provider chooses the following two items according to the actual situation, and if you don't know how to choose, you can directly select the first item to automatically select it, which is convenient for the new.

Hand operation, click next after selection;

6. Enter the password applied for from the network service provider, and go directly to the next step after the input is completed;

7. Set the wifi password, try to make the alphanumeric combination more complicated and not easy to be rubbed off the network.

8. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

The TL-WR842N wireless router has the following steps to set up the Internet access:

<> Step 4: Fill in the broadband and password at this step, if you don't remember the password, you can call ** to the operator to ask.

Step 5: Set up the wireless connection, select WPA2-PSK in the security options and set the wifi password, click the mouse Next, and then click Finish, so that the setting is complete.

2. Then set the password to log in to the router.

5. Enter the wifi name you want to set, enter the wifi password, click , and then click confirm to set up the router.

6. Complete the renderings.

The TL-WR842N wireless router has the following steps to set up the Internet access:

Step 4: At this step, fill in the broadband account and password, if you don't remember the account password, you can call ** to the operator to ask.

How to set up the TL-WR842N wireless router:

Home Network Environment Cabling]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Turn on the router's wireless function].

1. Select Wireless Settings --- Basic Settings.

2. Check [Turn on wireless function] and click Save.

Set wifi password].

1. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.

TPLintL-WR740N has 4 LAN ports and 1 WAN port, which are marked with small English letters on the router's interface. The WAN port is used to connect the external broadband inlet network cable, and the LAN port is the connection between the intersection device and the computer. The blue ones are WAN ports, and the other four are LAN ports.

Routing settings.

Open the browser on the computer, I use Google Chrome here, enter in the address bar, press enter and the login settings interface appears.

Generally, the default user and password are admin, and the router settings interface appears after entering.

Enter your account and password, the general initial password has its default in each place, and you need to provide it from the network operation provider. After completion, continue to click Next, since the author's route is wireless routing, the following figure is about wireless routing, if you are not a reader who uses wireless routing, you can skip this step.

In the red line area, set up a wireless connection, which is the password for the wifi. If you don't set it, it's easy to rub the net.

Finally, click Next to restart the route.

It's very simple.

Enter the IP address of your router to enter the settings.

Just follow the setup wizard prompts.

If the cat is connected to the wireless router: plug in the wireless router, do not connect the cat first, connect the computer to any LAN port of the wireless router, enter the browser to enter the settings page, and set it according to the PPPoe (ADSL virtual dialing) method. Then set the SSID, encryption method, and password again.

Save, restart. After setting, connect the network cable from the cat LAN port to the WAN port of the wireless router.

Connect the router and configure.

Method Step 1:

First of all, we need to connect the LAN port of the router with a network cable

The router has a total of five ports, four LAN ports, and one WAN port, and connects its host to any LAN port of the router.

Method Step 2:

The other end of the network cable connecting the LAN port is connected to the network port behind the host

Method Step 3:

The XP system right-clicks on the "Neighbor Network" ---Properties" -- to find the local connection.

In Win 7, right-click on "Network" ---Properties" -- find the local connection.

Then right-click on "Local Connection" --> Properties -->Internet Protocol --> Properties --> to get it automatically instead.

Note that this step can be ignored! The purpose is to check whether the local IP address is in the same network segment as the default address of the router, and the default is this network segment.

Method Step 4:

Determine if the machine is physically connected to the router properly:

If your computer automatically obtains the IP address, then you will see the IP address you obtained in the right-click --- Status - > Support on the local connection as shown in the figure below, and the address type is "Automatically obtained".

If your IP is manually configured, then use the third step to change it to "auto-acquisition".

Method Step 5:

After confirming that the above is correct, log in to your own route in the browser

The default IP address for this route is ".

Enter this IP in the address bar of your browser and press enter.

Method Step 6:

After connecting is the configuration wizard, which asks you to set the password for the management router, click Next after setting, enter your broadband user and password in the configuration wizard, and click on the green right arrow.

Method Step 7:

Set the wifi name and wifi password, and then click the green right arrow as well.

Method Step 8:

If all of the above settings are correct, click "Confirm".

Wait for the route to automatically load into your configured configuration, and the router can start autodialing!

Method Step 9:

Finally, connect the cable that the person with the broadband installed gave you to the blue port of the router.

The router will automatically dial for you, if you enter the broadband account and password correctly, and the network cable is connected correctly, then the dial-up will be successful soon, and the computer will be able to access the Internet.

Which one is your online provider? Is there a broadband cat? A complete response to the question is required; Feel free to ask!

No uplink and downlink Network connection is unsuccessful No problem with account and password?

Are you ADSL, the access mode of the fiber optic modem, do you need to dial up?

Problems with Internet accounts and passwords.

Open Internet Explorer or another browser and type it on the address bar.

Please click Enter a description.

To log in for the first time, you need to set an administrator password, and then click "Confirm" to continue.

Please click Enter a description.

Please click Enter a description.

Go to the setup wizard page and click "Next".

Please click Enter a description.

Here is the key, if the carrier's cat or modem device does not have the dialing function, select PPPoE, if there is already a dial-up function in the carrier's cat or modem device, then select the dynamic IP. It's time to ask your carrier here. Here take PPPoE as an example, select PPPoE and click "Next".

Please click Enter a description.

Here you need to ask your carrier to get an Internet account and password. Click "Next" after entering.

Please click Enter a description.

When you come to the wireless settings page, the device SSID is the wireless network name, then click WPA-PSK WPA2-PSK, enter the password of more than 8 digits, and then click "Next" to continue.

Please click Enter a description.

Finally click "Done".

Please click Enter a description.

At this point, the wired and wireless of the TL-WR841N wireless router are all set up.

1. Open the router in the computer and enter the password in the router to log in to the router management page.

2. After entering the management page, click the Setup Wizard option on the page.

3. Click the Next option in the pop-up page.

4. On the next page, click to select the PPOE dial-up connection method. and tap on the Next option.

5. Enter the corresponding broadband and password in the pop-up page and click Next.

1. Open the browser, clear the address bar, enter, and press Enter.

2. Set the administrator password in the Set Password box, enter it again in Confirm Password, and click Confirm.

3. After logging in to the management interface, the router will automatically detect the Internet access mode (if it is not the first time to log in, click the Setup Wizard in the lower left corner of Advanced Settings), as follows:

4. Enter the broadband service provider in the broadband field, and fill in the corresponding broadband password.

5. Set the wireless name and password, the wireless name is not recommended to set Chinese or special characters. As shown below:

6. After the setup is complete, click Confirm, and the setup wizard is complete.

7. The setup wizard is completed, enter the main interface of router management, observe the status bar, if the Internet Settings is displayed as follows, it means that the network connection is successful.

1. Connect to the TL-WR840N router.

2. Set the IP address of the computer.

3. Set up the TL-WR840N router.

4. Check whether the setting is successful.

1. Log in to the management interface, open a web browser, enter the management IP address of the TL-WR840N router in the address bar of the browser, press enter, enter the user name and password, and click the OK button.

2. Run the Setup Wizard, when you log in to the management interface of the TL-WR840NN router for the first time, the system will automatically run the Setup Wizard, if not, please click the Setup Wizard option in the left navigation menu to run.

3. Choose a way to access the Internet.

4. To configure the Internet account, please fill in the Internet account and Internet password according to the broadband user name and password provided by the ISP broadband operator, and click Next.

5. Wireless network settings, select Wireless Status to turn on, click to set SSID, SSID is the name of the wireless network.

6. Click Restart, and the Internet access parameter settings and wireless network configuration on the TL-WR840N router will take effect after the reboot of the TL-WR840N wireless router is completed.

You can do this by following these steps::

First, connect the broadband cable to any WAN port of the router, and confirm that the indicator light of the corresponding interface is shining or flashing normally.

After connecting the router to the phone, the login screen of the router will pop up. When it does not automatically pop up, you can open the router management address through the mobile phone browser, and in the management interface, you can set the administrator password;

After logging in to the interface, operate according to the prompts, detect the network, and set the Internet access parameters;

In the wireless settings page, you can modify the wireless name and wireless password, and set wireless parameters.

After completing the setup, the phone reconnects to the wireless signal, and if the Internet can be accessed normally, the router is set up.