How to install the sealing strip of the Pentium rice cooker

1.Cover the cover with 2 screws and unscrew them with a "Phillips screwdriver".

2.The lid has two layers, and the two layers are linked with a plastic lock"A flathead screwdriver separates the latch and separates the two layers of the lid.

3.When the lid is separated, you can see that there are 8 screws inside, and you can unscrew them with a "Phillips screwdriver".

4.Install the seal.

5.Tighten 8 screws, put the 2 layers of cover together, and screw 2 large screws.

You bought a 5L computer cooker, 1 A small amount of rice refers to the function set by 1 person to eat and only cook a little bit of rice, 2 The general water mark is below 2, and you can use steaming.

3 The computer rice cooker has a bimetal patch thermostat, which is very sensitive to temperature sensing, and the cooking time is measured by the temperature, so it is interrupted and restarted, there is no impact.

4 Anti-dry boiling, automatic power-off is the function of every rice cooker, this is a low-end computer cooker, the safety performance is reflected in the materials, such as gas-assisted injection molding technology, anti-impact shell, anti-slip silicone mats, etc.

Thank you for giving me a refresher on the product knowledge.

When I was washing the pot that day, I felt that the rubber strip was a little dirty, and I thought it was very easy to install, but I couldn't install it after removing it, what can I do to solve this problem?

Required height training tools: sealing ring, screwdriver.

1 First, pull down the breathing hole cover with your fingers.

2 Open the lid of the rice cooker with a ruler.

3 Use a Phillips screwdriver to remove the two screws at the bottom joint.

4 And the one on the right side is unscrewed.

5 Open the built-in buckle in the housing in turn, in the order of large batch and small batch.

6 And the edge of this place shall be warped.

7 After prying, the cover can be removed.

8 .Press down on the lid of the rice cooker to close it.

9 Use a Phillips screwdriver to remove the eight screws of the sealing ring aluminum cover.

10 Remove the aluminum cover of the seal.

<>12 Remove the aluminum cap of the sealing ring and place it in place. Note that the small hole in the middle is aligned with the middle of the connection.

13 Correct the position, open the outer cover, and carefully and gently snap it back.

14 Replace the two screws at the joint.

15 Finally, put back the breathing hole cover and the sealing ring is installed.

How to install the four small rubber rings of the Pentium rice cooker 1, you have to prepare two things, one is a screwdriver, and a sleek plastic part (to be slightly harder) 2, use plastic parts to remove the upper cover of the rice cooker, the upper cover is composed of two large plastic parts to separate it. 3. Use a flathead screwdriver to warp up a few small aluminum pieces on the edge of the aluminum plate. The aluminum sheet can then be removed.

4. After the aluminum sheet is removed, the sealing ring is installed on the aluminum plate, and then the aluminum plate is installed on the plastic parts. Since the process is relatively complicated, please also send your rice cooker to the maintenance department for repair, so that you can watch the kitan from the sidelines, and you can replace it yourself the next time your itchy hands are torn off. It is better to send it for repair.

How to install the four small rubber rings of the Pentium rice cooker 1, you have to prepare two things, one is a screwdriver, and a sleek plastic part (to be a little harder) 2, use plastic parts to remove the upper cover of the rice cooker, the upper cover is composed of two large plastic parts to separate it. 3. Use a flathead screwdriver to warp up a few small aluminum pieces on the edge of the aluminum plate. The aluminum sheet can then be removed.

4. After the aluminum sheet is removed, the sealing ring is installed on the aluminum plate, and then the aluminum plate is installed on the plastic parts. Due to the relatively complicated process, please also send your rice cooker to the maintenance department for repair, so that you can watch from the sidelines, and the next time you have an itchy hand and tear it off, you can also replace it yourself.

Summary. Remember to disconnect the power supply when putting on the lid of the rice cooker, and then use a rag dipped in detergent to clean, for more stubborn oil stains, you can use a toothbrush to brush directly on it several times, so that the stains can be effectively cleaned up, after all are cleaned, then use a dry rag to wipe the water on it.

For stubborn oil stains, you can use a toothbrush to brush directly on it several times, so that the stains can be effectively cleaned up, and after all are cleaned, then wipe the water on it with a dry wipe to wipe the water on it dry.

1.Take out the inner liner of the rice cooker, pour in an appropriate amount of rice, and then pick up water to wash the rice, and after washing the rice, take a small amount of water, 2Before cooking, wipe all the moisture around the inner bowl and put the inner tank into the shell of the rice cooker3

After stabilizing the finches, you can close the lid of the pot, connect the power supply, and turn the place with the indicator light to the button for cooking rice, and the rice pot trips.

Open the lid of the rice cooker, and there is a stainless steel inner ring with a sieve hole at the position of the sealing ring, don't pry it open with a screwdriver (the one I traced with red thread), because the back of the stainless steel inner ring is screwed on with several screws, if you insist on priing it open, the lid of this rice cooker will be broken. The seals can no longer be installed.

Other parts of the rice cooker do not need to be removed (such as the handle of the rice cooker, etc.). That vent is movable and can be taken down.

Use a flat-headed screwdriver, put it on the clasp of the lid, pry open a slit, pry open the entire outer lid along the edge, how to see the structure inside, unscrew the screws I mentioned above, put the sealing ring away, screw it back, buckle the cover, and you're done.

The sealing ring on the lid is soft jujube ear plastic, under normal circumstances, the edge of the lid will be buried in a circle of grooves, put the sealing ring flat by hand, against the edge of the groove, and press it in a little bit in a clockwise direction.

Below is the installation of a rice cooker's sealing ring**:

<> the third picture is the most difficult and critical part, the lid has a total of six bayonets, the upper two don't pry the family pat, just pry open the four on both sides, and then lift it up to come out. Be careful not to use too much force when prying the bayonet, and the gap can be padded with a thick piece of paper to avoid covering the shell**. In the fourth figure, when the aluminum sheet is returned, it should be in the same direction as the original, because it is easy to break in the opposite direction.

The small aluminum sheet with round holes in the fifth figure is positioned, and it is enough to align this when installing.