What is a sliding window seal? Sliding window sealing strip installation method

First clean the dust above the window side shelf, then push the window seal into the window frame in the order from left to right, top to bottom, and then remove the extra parts at both ends of the adhesive strip with scissors to ensure that the 4 corners of the window seal can be connected. When attaching the sealing strip to the window, it is important to note that the length of the sealing strip is 2 to 3 cm larger than that of the window, and that the corners must be firmly glued with glue.

Smell it with your nose first, if there is a strange smell, if there is, it means that it does not meet the standards of environmental protection, and it is not recommended to buy. Then check whether the outer layer of the sealing strip is smooth, whether there is any contaminated area, if there is, it means that the quality of the sealing strip is poor, and it is not recommended to buy.

The installation part of the wool top is generally on the door and window sash, the surrounding of the frame fan or the sealing bridge (wind block) to enhance the sealing between the frame and the sash. If the size of the wool top is too large or the vertical hair is too high, it is not only difficult to assemble, but also increases the moving resistance of the door and window, especially the initial resistance of opening and the in-place resistance of closing. The specification is too small, and the height of the vertical wool strip is not enough to easily get out of the groove, which greatly reduces the sealing performance of (door) and window.

The tops need to be siliconized, and the appearance of the tops with qualified quality is straight, and the bottom plate and vertical hairs are smooth. No bending, no pitting on the base. Bubble.

The vertical hair is firmly bonded to the bottom plate, the density is uniform, and it is not easy to lose hair.

Answer: Hello, if you want to paste the sealing strip of the window, you need to clean all the parts to be pasted, including the dust in the gaps, etc., to ensure the tightness of the door and window sealing strip equipment and notch.

2.Next, we remove the tape of the sealing strip, stick it on the position that needs to be installed, and when it comes to the interface at both ends, retract the sealing strip to the notch, leaving a certain distance, leaving about 3 cm, and there is a margin.

3.Cut the sealing strip again, press the excess into the inner groove several times, so that the self-adhesive of the sealing strip and the door and window are tightly pasted together.

4.When pasting, you need to pay attention to the first to remove some debris in the notch, which is a necessary step, do not try to save trouble, otherwise if the area is full of dust, directly paste the sealing strip, which will affect the bonding effect.

Now there are many window style choices, mainly divided into fixed windows, casement windows, sliding windows, etc., and different styles of windows are different. Sliding windows are more common in modern homes, which are flexible and convenient to use, and will not take up too much indoor space. When installing the sliding window, it is necessary to install the sealing strip to ensure the sound insulation and water insulation effect, so what is the installation tutorial of the sealing strip of the sliding window?

Let's take a look with Qeeka Home experts.

1. What is the installation tutorial of sliding window sealing strip rotation.

First of all, determine the size of the sealing strip, because it is installed on the window sash, and the length must not exceed the length of the window frame, and it needs to be cut in advance according to the size of the window sash; Then find the special sealing strip slot on the window frame, and stuff the cut sealing strip into it, so that there must be no unevenness, curling, stretching and other problems; Finally, push the sash to see if it is smooth to use.

Second, what should be paid attention to in the installation of sliding window seals.

1. Pay attention to cleanliness.

Before the installation of the sliding window seal, the notch needs to be cleaned to ensure that the installation notch is free of debris and dust, otherwise it will affect the installation, and the glass does not correspond to the notch, and it also has an impact on the seal.

2. Pay attention to inspection.

Before installation, it is also necessary to check the glass and window frame to avoid the problem of uneven slotting gaps, otherwise the rubber strip will not be in good contact with the glass slot, or even protrude out of the slot, so that in use, it is easy to fall off the slot.

3. Pay attention to the corner position.

When the sealing strip of the sliding window is installed in the corner position, it should be noted that the adhesive strip cannot be disconnected, otherwise the sealing effect will be affected, and at the same time, it needs to be glued for bonding to ensure that it will not fall off during use.

4. Pay attention to inspection after installation.

The sliding window sealing strip should be checked under the thickness of the installation, and the window sash can be pushed to see if there are problems such as uneven gaps in the window frame, unclose sealing strips, and uneven installation.

Summary: The above is about what is the installation tutorial of sliding window seals, and what to pay attention to in the installation of sliding window seals, I hope the content shared can give you some reference, if you want to know more about relevant knowledge, you can **** Qijia information.

Sliding windows can often be seen in our daily life, and after this sliding window is installed on the track, the sound is relatively small when sliding, and the sealing effect is also very good. Mainly because of the role of the sealing strip sail, what are the ways to install the sealing strip in the sliding window?

1. How to install the sealing strip of the sliding window.

1. The sealing strip of the sliding window is generally installed on the sash of the sliding window, and the sealing of the door frame and the sliding window can be strengthened around the frame of the door and window and the wind shield.

2. Before installation, we need to clean the gaps in the door frame, and the next thing is to fill the sealing strip between the glass to fix it.

3. Then squeeze in the special glue, squeeze the glass with a sealing strip, and wipe off the excess glue. When squeezing the glue, you need to pay attention not to squeeze too much, after injecting the sealing strip, you must ensure that the sliding door does not move before fixing, so that the sealing effect will be better.

Second, what aspects need to be paid attention to when installing the sealing strip.

1. If it is a rubber sealing strip, remember not to pull it too tightly when installing, and it must be arranged in place to make the surface straight.

2. In its corner position, we can cut off the excess rubber strip, and then inject glue into the disconnected place to ensure that the joint is firmly sealed.

3. It is necessary to fix it with sealant, leave a certain gap, and then inject glue, and pay attention to the depth when injecting glue, and at the same time, before the glue is completely solidified, the sliding door or glass can not be shaken.

4. Generally speaking, the sealing strip of the wool strip will be installed at its sash, and we must pay attention to the sealing, otherwise we will encounter some problems in the later use.

5. When installing, it should be noted that the rubber strip should be retracted to the middle, leaving about two centimeters of space, because the thermal expansion and cold contraction in the later stage may be squeezed.

The above content is about how to install the sealing strip of sliding doors and windows, and what aspects need to be paid attention to when installing, it is best to ask professional personnel to operate, if you can't, the installation effect may not be good.

The biggest role of doors and windows is to avoid rain erosion and wind protection, but whether these properties are good or not often depends on the quality of the sealing strip. What are the materials of sliding window seals? Today, we will introduce the relevant content below, let's take a look at the sliding window seal!

Sliding window sealing strip material.

The most common sliding window sealing strip material can be divided into two categories: rubber strip and wool top, of which the wool strip is suitable for all kinds of door and window products, as the sealing connection between the overall frame and the door and window sash, but the rubber strip is only suitable for the dense balance car seal between the glass and the door and window sash, so the sliding window is mostly sealed with rubber strips, and there are slots of hidden high doors inside the window, which is convenient for the sealing of rubber strips, and at the same time, the window glass and frame are tighter to ensure the service life of the sliding window.

Precautions for sealing strip installation.

1.The installation of the sealing strip is relatively simple, and there are generally certain slots inside the doors and windows, and the rubber strip is directly installed according to the corresponding position. However, it should be noted that the flatness of the rubber strip should be ensured during installation, and it should not be bent and deformed, otherwise it is easy to cause poor sealing effect.

In addition, the rubber strip joint should not exceed one millimeter, and the product model should also match the door and window slots, so as not to be too large and unable to press in. If the sealing strip is too small, it is easy to cause gaps in the slots, resulting in loose doors and windows. In the selection of materials, we should use high-quality, green and environmentally friendly rubber strip products.

2.The wool top is mostly installed on the door and window sash or the periphery of the frame, so as to increase the sealing effect between the frame and the door and window sash, but the size of the wool top should not be too large or too high, so that the installation is more troublesome, and it is not convenient to use, so that the sliding doors and windows are opened and closed. If the size of the wool top is too small, it is easy to have the problem of desolation, which greatly reduces the sealing effect of doors and windows.

When purchasing, you need to see whether the material has been silicified, whether the surface is flat, and whether it feels smooth. Excellent wool tops are not prone to hair loss, no bubbles are generated, and the adhesion is high. 3.

When the rubber sealing strip is installed, the tension should not be too large, and the standardized installation should be carried out in strict accordance with the position. The rubber sealing strip should be kept vertically level, with a flat surface and no bending. For window installations, the rubber strip should fit snugly against the glass, but should be uniform in terms of force.

The corners also need to be treated with an inclined plane, and then the construction of glue is carried out to make the doors and windows more durable.

About sliding window seals.

Sliding window Sliding window seal.

When installing doors and windows at home, there are many places that need to be paid attention to, for example, some people will install sliding doors and windows in the kitchen or bathroom, and there is a sealing strip for sliding doors and windows that must be installed in place. What do I need to pay attention to when installing?

1. How to install the sliding window sealing strip in place.

1. The sealing strip of the sliding door is generally installed on the sash of the door and window, and there is a special sealing strip slot. So we only need to clamp the sealing strip on top of the strip groove, and the surface should be very flat, relatively smooth, without any bending.

2. The position of the corner needs to be paid attention to, the sealing strip can be cut from the inclined plane, and then in the place of disconnection, we can apply glue on the surface and paste it firmly.

3. When pasting, you can fix it with sealant, so that the gap is very firm, and then you can use the sealing strip to leave a gap in the glass to inject glue, and the thickness of the glue injected should generally not be less than 5 mm, and to ensure that the glass can not be shaken before the glue solidifies, so that the sealing strip is installed in place.

Second, what aspects need to be paid attention to when installing the sealing strip.

1. When installing the sealing strip, we need to press the head of the sealing strip down, and then embed it into the strip groove. So when installing, we can install the strip at the interface at both ends, and then retract it a little in the middle, leaving about two centimeters of space, and then cut it short and embed it into the notch.

2. In order to increase its tightness, we can choose to fill it with sealant, so that the gap is completely filled, and there will be no gap.

Third, the types of door and window seals.

1. Glass sealing strip, this kind of glass sealing strip can be used to seal the gap between the glass window and the door frame, which has a very good sealing effect.

2. In addition, there are some sealing strips for door leaves and door covers, which are used for sealing plastic windows or wooden doors and windows, and can also play a waterproof effect.

3. There is also a wool top, which can be installed on the top of the sliding door type door and window to seal the gap between the window frame and the door leaf.

Summary: If it is a sliding door, you need to choose the corresponding sealing strip, and then install it according to the correct method to ensure and meet the relevant standards, so that it will not affect the use of the sliding door.