What is the installation method of window seals, and what should be paid attention to when installin

First clean the dust above the window side shelf, then push the window seal into the window frame in the order from left to right, top to bottom, and then remove the extra parts at both ends of the adhesive strip with scissors to ensure that the 4 corners of the window seal can be connected. When attaching the sealing strip to the window, it is important to note that the length of the sealing strip is 2 to 3 cm larger than that of the window, and that the corners must be firmly glued with glue.

Smell it with your nose first, if there is a strange smell, if there is, it means that it does not meet the standards of environmental protection, and it is not recommended to buy. Then check whether the outer layer of the sealing strip is smooth, whether there is any contaminated area, if there is, it means that the quality of the sealing strip is poor, and it is not recommended to buy.

Installation steps of plastic steel window seals.

1.Measure the height of the door and window first, and cut the sealing strip of the glass curtain wall with scissors according to the height.

2.First of all, clean the surface to be pasted, so that its surface is relatively clean, smooth, flat and dry.

3.Use the same procedure to install the horizontal sealing strip, pay attention to the anastomosis at the corner joint, and there should be no gaps between the joints.

4.Keep removing the protective paper on the back so that the sealing strip runs down the frame, and keep pressing down. Be sure not to stretch.

5.Pay attention to: the position of the sealing strip at the hinge.

6.Also remove the protective paper attached to the back of the section, install the sealing strip in the correct part and press it tightly, which should be as aligned with the top edge as possible.

Precautions for sealing strip installation.

1.Before installing the glass, it is necessary to clean up the stolen goods in the notch, and it is necessary to carefully align the glass when installing it to ensure that the gap on both sides is even, and it is fixed in time to prevent collision and displacement and deviation from the notch.

2.When installing the rubber sealing strip, it can not be pulled too tightly, the length should be measured clearly, and the installation should be inlaid in place, the surface should be straight, and the glass and glass notch are in close contact, so that the force around the glass is uniform. At the corner, the rubber strip should be disconnected on an inclined plane, and the glue should be injected at the disconnection place to bond firmly.

3.To fix the sealant, the rubber strip or rubber block should first squeeze the glass, leaving a gap for glue injection, the glue injection depth should not be less than the length of the window, and the glass should be kept from vibration before the glue cures.

4.The installation part of the wool top is generally on the window sash, around the frame sash or on the sealing bridge, to enhance the sealing between the frame and the sash.

5.The size of the wool top is an important factor affecting the performance of sliding doors and windows and watertightness, and it is also an important factor affecting the opening and closing force of doors and windows. If the size of the wool top is too large or the vertical hair is too high, it is not only difficult to assemble, but also increases the moving resistance of the door and window, especially the initial resistance when opening and the resistance in place after closing.

When installing, it should be inlaid in place, the surface should be straight, and the glass and glass notch should be in close contact, so that the force around the glass should be uniform, and the rubber strip should be disconnected on an inclined plane at the corner, and the glue should be injected and bonded firmly at the disconnection.

Before installing the glass, it is necessary to carefully remove the debris in the notch, such as mortar, brick chips, wooden blocks, etc., and the glass should be carefully aligned when placed to ensure that the gap on both sides is uniform, and it should be fixed in time to prevent collision and displacement, and deviate from the center of the notch. The rubber sealing strip can not be pulled too tightly, and the blanking length is 20-30mm longer than the assembly length.

When fixing the glass with sealant caulking, the glass should be squeezed with rubber strips or rubber blocks first, leaving a gap for glue injection, and the glue injection depth should not be less than 5mm, and the glass should be kept from vibration before the glue cures.

Answer: Hello, if you want to paste the sealing strip of the window, you need to clean all the parts to be pasted, including the dust in the gaps, etc., to ensure the tightness of the door and window sealing strip equipment and notch.

2.Next, we remove the tape of the sealing strip, stick it on the position that needs to be installed, and when it comes to the interface at both ends, retract the sealing strip to the notch, leaving a certain distance, leaving about 3 cm, and there is a margin.

3.Cut the sealing strip again, press the excess into the inner groove several times, so that the self-adhesive of the sealing strip and the door and window are tightly pasted together.

4.When pasting, you need to pay attention to the first to remove some debris in the notch, which is a necessary step, do not try to save trouble, otherwise if the area is full of dust, directly paste the sealing strip, which will affect the bonding effect.

Window weatherstrip installation method tutorial, the little brother said in detail, do you understand.

Hello, this generally has a manual, you can see it by looking at it.

With the continuous development of modern society, we pay more attention to the quality of life, the quality of the living environment affects part of their quality of life, so good decoration is essential, the following is a detailed introduction by me for you, window sealing strip installation steps and how to use.

How to use the window leaky stool seal.

Glass mat strip and mouth strip: (window frame, window sash) should be welded to clear the angle of the strip according to the correct direction with a special roller to push the strip into the profile notch, and at the same time press the head of the strip down to the embedded profile notch. Since the bead is an elastomer, retraction may occur after being rolled down, and the correct way to do this is:

When the strip is installed at the interface at both ends, retract the strip a little in the middle, leaving a shrinkage margin of 2-3 cm, and then cut it and insert it into the notch.

Glass stripping: Insert the tip of the strip into the profile groove by hand according to the correct side, and then press the exposed surface of the strip hard to press the strip into the gap between the glass and the profile. The strips at both ends are retracted a little to the middle, leaving a length of 1-2 cm, then cut and pressed into the notch.

The use of window seals.

According to the different uses, window seals can be divided into three categories: door cover seals, wool strips, and glass seals (rubber strips). The sealing strip of the door sleeve is mainly used for the sealing between the door panel and the door frame, while the wool strip is mainly used for the sealing between the door frame and the door leaf, and the glass sealing strip is mainly used for the sealing between the glass and the door leaf and the frame.

Window seals can not only play the role of sound insulation and waterproofing, but also play the role of energy saving and warmth, so the installation process of the door material is very particular. In terms of material, it must have good tensile strength and good elasticity, and aging resistance and temperature resistance are also indispensable. There is also a good match between the specifications of the door and window sealing strip and the door and window slots.

Door and window seals are divided into two types: glass sealant strips and wool tops. The sealing strip rubber strip is generally used on the door and window sash, and there are special sealing strip grooves on the pressing strip and the door and window, the main function is to wear the sealing strip on the pressing strip and the inner sash to make the glass and the frame sash tighter, so as to ensure the airtightness of the door and window.

The installation part of the sealing strip should be flat, not curled, not stretched, the joint should be less than 1mm, the model of the sealing strip should match, too large so that the strip can not be pressed in, too small will make the strip easy to fall off, the glass collapse and the fan is not tight, there will be gaps. The sealing strip should be non-toxic. Odorless and environmentally friendly special sealing strip.

The installation part of the wool top is generally on the door and window sash, the surrounding of the frame fan or the sealing bridge (wind block) to enhance the sealing between the frame and the sash. If the size of the wool top is too large or the vertical hair is too high, it is not only difficult to assemble, but also increases the moving resistance of the door and window, especially the initial resistance of opening and the in-place resistance of closing. The specification is too small, and the height of the vertical wool strip is not enough to easily get out of the groove, which greatly reduces the sealing performance of (door) and window.

The tops need to be siliconized, and the appearance of the tops with qualified quality is straight surface, and the bottom plate and vertical hairs are smooth. No bending, no pitting on the base. Bubble.

The vertical hair is firmly bonded to the bottom plate, the density is uniform, and it is not easy to lose hair. Doors and windows have excellent sealing and watertightness, but what about sound insulation? Naturally, it was handed over to the insulating glass --- the sound insulation master of Tuanji.

Two or more pieces of glass are marked with butyl rubber on all four edges of the glass through an aluminum alloy spacer (filled with desiccant) and a corner column spacer. polysulfide rubber; Make it form a stationary, dry gas, and have the properties of a vacuum. Insulating glass is thermally insulated.

Seal. Frost protection. dustproof and soundproof, etc.

A variety of superior performance. Therefore, many users agree with it. The inside of good insulating glass should be clean.

No dust. There is no moisture.

Good doors and windows are inseparable from the production and installation, and the standard of production is indispensable for high-standard doors and windows. The production equipment and process determine whether the overall performance of doors and windows is excellent. According to the requirements, the diagonal difference of plastic steel doors and windows should be controlled within 2-3 mm, with strict process parameters and control range, which requires a certain production equipment and technology to ensure that there is a high-quality workforce.

Therefore, there is a world of difference between the plastic steel doors and windows produced by street workshops and regular manufacturers. Three points of production, seven points of installation, if you do not pay attention to the installation standards, it can cause deformation of doors and windows. Ruler Jane.

The thermal coefficient of plastic steel is almost 6 times that of steel. Therefore, expansion joints must be left between the window frame and the wall to prevent thermal expansion and cold contraction or slight settlement of the house, which will deform the doors and windows. At the same time, in order to ensure waterproofing.

Heat preservation. For sound insulation, the expansion joints must be filled with an elastic material and then sealed with sealant. These materials are high in quality, and the quality varies greatly, so it is necessary to strictly prevent cutting corners and shoddy when installing.