Is it normal for the bathroom to stick bricks and still be damp after two months?

Bathroom tiles are still very humid after two months of sticking, this is related to the environment and air humidity where you are located, in Guangdong every year in April and May there will be water droplets flowing out on the tiles, which shows how much air humidity affects the tiles.

It's normal, even though you've taken him up. The moisture in the cement still doesn't come out so quickly. Because, this is the first half of the year, the air is very humid. You want him to dry quickly, that's not possible, just be patient.

This depends on the climatic conditions of your region, you know that our country is vast, the temperature and ventilation difference between the north and the south and the east and west is very large, if it is not dry in the humid area for 2 months is still very normal, if it is a dry area in February is not dry, it is a little too much, it is recommended to find the decoration team to see again, is there a problem with the ratio of cement and sand, I hope to help you.

Hello, if the wall is this reason, it must be the wall is damp, and it is normal for the ground to be damp after moving in.

Hello, it is normal for the bathroom to be damp all the time after tiling.

Because, it may be that the toilet is poorly ventilated, and the water volatilizes slowly and will damp.

Also, if you usually use water in the bathroom frequently, it is not easy to dry.

See you're a**? If it's in the south, it's normal, and if it's in the north, it's absolutely abnormal.

The floor tiles have been paved for a month and a half, and the damp place on the wall is still not dry, indicating that the wall is seeping, check whether the water pipe is leaking, or the bathroom is leaking, and there is a ditch outside the wall to draw the outer wall more than one of your indoor walls with mud pavement will lead to water seepage, carefully check the waterproofing will completely solve the problem of moisture.

In general, dampness is the main cause of mold on the wall. There are several reasons for the dampness of the wall, the first is that the external wall is cracked and cracked, and the liquid water such as external rainwater will seep into the wall through the cracks, resulting in dampness and mildew of the wall; The second is that most of the houses are now frame structures, and the walls are filled walls, and the junction between the wall and the beams and columns is prone to cracks, which is the weak point of insulation and waterproofing. In summer, especially in the rainy season, it is easy to seep water, and in winter, the temperature difference between indoor and outdoor is too large, the wall is cold, the indoor is hot, and it is easy to produce condensation, so the wall is damp and moldy if it is not treated in time.

Find out the cause of dampness on the wall, and solve the problem to effectively remove the mold. The first case is to add a waterproof layer, which can effectively prevent external water from seeping into the wall. The second situation is caused by insufficient wall insulation, which can prevent the occurrence of cold bridge phenomenon by increasing the insulation layer, install insulation wall panels on the wall, strengthen the insulation of the inner wall, and prevent the formation of a humid environment, the indoor air is similar to the wall temperature, and the wall is not easy to produce condensation, and naturally it will not cause mildew caused by moisture.

If you simply pick.

There is a pipe leaking on the ground. Sometimes the water pipes are only in the bathroom and kitchen, but there is a leakage point where the leakage is not necessarily in the leaky area, the water is to go low in the bathroom and waterproof, it must be the floor where the low water goes, you see if the downstairs of your house is leaking, if the water leaks then you are looking for the reason in your home.

After the floor tiles have been laid for a month and a half, the wall is damp and not dry, you should check that there must be a leak in the water pipe of your house, and look at the top surface of your downstairs home, if there is also moisture, then it must be a slight leak in the water pipe of your house.

Is ventilation maintained? Let the wind blow away the moisture in the room.

<> the water vapor in the bathroom is relatively heavy, if the ventilation is not good, it is easy to cause the bathroom to be more humid during the demolition period, so what should I do if the bathroom floor tile joints have been wet? Rilong HomeLet's explain it to everyone.

Measure 1: Beautiful sewing.

The seam is the most commonly used and very effective way to deal with the gap of ceramic tiles at this stage, and the material used in the seam is a professional seam agent. The gaps of the tiles are filled with a grout, and then the gaps are plugged with a solidified substance formed by the solidification of the grout. This eliminates the accumulation of water in these areas and prevents water from the floor from entering the gaps in the tiles.

Fundamentally solve the dampness of the gaps in the tiles.

Measure 2: Brush waterproof glue on tile gaps.

The so-called waterproof glue for tile gap brushing, in fact, its principle of action is basically the same as that of the beautiful seam, but it is the use of professional waterproof glue to paint the gaps of the tile. In this way, it also eliminates the accumulation and infiltration of water in the tile gaps, and solves the problem of moisture resistance in the tile gaps.

After a month of paving the bricks in the bathroom, can you caulk if you get wet?

Hello dear tile joints can not be done if they are wet with water, because the caulk will cause dampness or discoloration when it comes into contact with water. Caulk is a mixture of cement, filler, pigment and modifier, which is used to fill the gaps between ceramic tiles. Combined with decorative materials such as ceramic tiles and stones, it can provide a beautiful finish, improve the bonding and impermeability between the facing tiles, and relieve the internal stress of the entire wall or floor covering material.