How to paste the Outlander door bumper strip better?

Did you suddenly get a circle when you just bought the anti-collision sticker? Take a small door anti-collision sticker and compare it up and down the door, but I don't know if it should be pasted on the **.

In order to answer this doubt for the majority of riders, Brother Ku specially found a few more common scenes for everyone, and tested different posting positions in a targeted manner, hoping to help everyone.

Before confirming the location of the post, we will clean the door to ensure that the poster is secure.

1. By the wall. If your car is often parked against a wall, and it is extremely easy to hit the wall when getting in and out of the car, then we will directly use the wall as a reference. Drive the car to the wall, open the door, and you can easily find the location of the collision.

Put on the crash stickers and see if they are in the correct position.

Once you've decided where to post it, mark it with masking paper.

Remove the adhesive protective film on the back of the anti-collision sticker.

Align the markers and post them.

PS: If it is really cold in winter, you can use a hair dryer to heat the adhesive, so that it can be more firmly pasted.

Once it's pasted, you're not afraid of hitting the wall with the door.

2. Between cars.

Because the door shape of each car is different, it is difficult to determine an absolute position for posting. The safest way is to look at the car that is often parked next to you, and then use it as a reference standard to see where it will hit when you open the door, and then stick it to which position.

3. Pillars. If your parking space is more complicated, with some pillars, fire hydrants, etc., the positioning method is to drive the car to the side of these obstacles, and then open the door to see where it needs to be protected.

The above three scenarios are more representative, the car is mainly used flexibly, because of the complexity of the parking environment and the irregularity of the door, so no position is absolutely safe, can only be posted according to the maximum possibility.

Are you talking about the anti-collision strips on the front and rear bars or the anti-collision strips on the doors, the anti-collision strips are basically decorative strips, the anti-collision strips on the front and rear bars are bonded with 3m double-sided tape, and the anti-collision strips on the doors are also bonded, some are bayonets, and some are fastened from the inside of the door with screws.

The car bumper strip is made of rubber or natural rubber, which belongs to the exterior decoration of the body, mainly to prevent damage to the parts by small frictions, and is generally installed at the corners of the doors and front and rear bumpers.

Car crash strips have a collision avoidance effect and play a role in protecting the body, but some people use it as an exterior decoration.

The function of the car anti-collision strip is to protect the body from being scratched, especially the position of the door, once the car is scratched, it is easy to damage the car paint, and even make the part of the paint rust.

Therefore, the anti-collision strip of the car can simply protect the paint from being scratched, protect the frequently used parts of our car doors from being scratched, and protect the integrity of the car paint.

1. Open the door and find a prominent position that is easy to be collided.

2. Rinse the car with water first, do not wipe the car directly with a towel, because when the surface of the car is full of dust and foreign objects, wiping the body with a towel is equivalent to wiping the car directly with sandpaper. Then use a towel to dry the place where the bumper strip is attached.

3. Slowly tear off the adhesive backing.

4. Stick it on the alignment position and gently press it for a while to make the adhesive strip fully stick to the surface of the car.

5. After the installation is completed, do not wash the car within 48 hours, otherwise the adhesive will lose its adhesion due to wet water.

The door bumper is mainly to prevent damage to parts caused by small frictions, and is generally installed at the corners of the door and front and rear bumpers.

The door bumper sticks to the most prominent part of the door, as if it is in the upper right corner!

Hello, it is generally better to stick it in the middle or lower part of the door edge.

He's usually like what to see or something?

It should be attached to the glass or the door to increase the health of the family, you can try it.

How to paste the car door bumper strip? With just a light touch, you don't have to worry about the door banging again.

Dip it with double-sided tape and stick it to the door. Anti-collision strips, also known as protective strips, anti-scuff strips, fender rubber strips, Robins, straps, etc. It is mainly used for the protection of inflatable boats, assault boats, drifting boats, yachts and various water amusement equipment and facilities.

How to paste the bumper strip:

Generally, it is recommended to use 3M glue, glass glue, and 205 glue for pasting.

However, there are disadvantages: the adhesive is too thick, resulting in undense paste; The adhesive performance is poor, and the bond is not strong and durable. Qiqi.com reminds that when the bumper is aged, cracked or falls off, it should be purchased and replaced with a new bumper in time.

The role of the bumper strip:

1. Increase the lines and dynamics of the car body, and play a decorative role.

2. Prevent the side of the car body from being abrased or bumped by foreign objects, and play a protective role. Since the bumper strip occupies a small proportion of the body area, when the side of the car body is hit, its protective effect is very small.

Dip it with double-sided tape and stick it to the door.

To use 3m double-sided tape, the trim and door should be clean before construction, stick the double-sided tape on the trim and do not tear off the plastic paper, bask in the sun, or put it on the dashboard with a warm air for 10 minutes, so that the plastic paper is removed and pasted on the door is absolutely reliable.

The first step is to clean the scuff strip and the body parts to be pasted, and remove the residual double-sided tape.

The second step is to stick double-sided tape along the four sides of the anti-scuff strip and do not tear off the plastic paper.

The third step is to fill the middle of the scuff strip with glass glue (black or white is acceptable) and the amount should not exceed the double-sided tape.

The fourth step is to wipe the body with a clean, dry cloth, then remove the plastic paper from the double-sided tape and attach the scuff strip.

The fifth step is to apply a little pressure and insist on five or six minutes OK, and it is best not to move the car for two days.

3m is the best. Other damage paints.

Which glue is used for adhesive rubber strips to be strong YH-818

Hello, it is best to use glue for two years.