How to control the car wading clutch? 50

The clutch should be in linkage or semi-linkage.

First of all, it is necessary to judge whether it is really necessary to wade and drive according to the situation at the scene, and if you can make a detour, it is recommended to take a detour; If things are not urgent, it is recommended to go back and wait for the water to be small. You have to know that once you fail to wade through the water, the trouble and loss caused to you is huge. Once you fail to wade through the water, you have to organize a tow truck, contact a repair shop, find a friend for help, and a series of troubles, plus the cost of repairing the car is more expensive than if you were on a plane.

If you do need to wade into the water, first determine how deep the wading is at the deepest point, which cannot exceed the midpoint of your wheel, which is the pumping point of the car. If there are vehicles passing through, the water surface height can be observed according to the passing vehicles; If there are no other vehicles, you can find a stick to test the depth of the water ahead. Do not wade through after knowing the depth of the water.

Please click Enter a description.

Do not wade in the water after another vehicle, and wait until the vehicle in front of you has completely passed or confirmed that it does not affect your passage before starting to wade, otherwise you will have to stop in the water once the vehicle in front breaks down, which will increase the danger. It is not possible to wade multiple vehicles at the same time, so that waves will form on the water surface and affect each other's direction.

Please click Enter a description.

The route of wading in the water should be driven according to the route of the safe passage of the vehicle in front, and no other way can be found; If it is passing alone, it is recommended not to drive in the middle of the road, because the manhole cover may be set up there, and once the manhole cover is lost, it will cause an accident; For more familiar road sections, you can drive according to your usual impression and avoid manhole covers.

Please click Enter a description.

When wading through the water, it is forbidden to stop in the middle and turn off the engine, hang 1 gear or 2 gears at a constant speed, the engine speed should be above 1000 rpm, maintain high-speed operation, and appropriately rely on the clutch and brake to control the speed, and pass cautiously.

Please click Enter a description.

When the vehicle wades in the water, in order to prevent the water level from suddenly not being able to escape, the window glass should be lowered in advance, and in the event of an accident, the door can not be opened, you can escape from the window.

Please click Enter a description.

Once the engine is turned off halfway, the key should be turned off immediately, the front cover should be opened to disassemble the positive wire of the battery, and the vehicle must not be started again. All you have to do at this point is contact the repair shop to prepare the trailer.

Please click Enter a description.

Please click Enter a description.

The car wades directly outside the party to the first or second gear clutch, don't care about it, pass slowly, don't go straight over, so that it will go directly to the car.

The car wading clutch can pass when the water does not exceed the clutch moisture, but if the water level is exceeded, the fire will cease.

It is best not to always wade in the car, which is very harmful to the car, and the shallow water level can be lifted and clutched.

The clutch pedal free travel is too largeThe stroke of the release bearing to push the release rod forward is shortened, and the stroke of the pressure plate is also shortened, so that the clutch can not be completely disengaged.

The distance between the double-plate clutch adjustment scythe and the middle driving disc is too small, resulting in the insufficient backward movement of the intermediate driving disc, so that it is not completely separated from the front friction plate; On the contrary, the distance between the adjustment screw and the middle driving disc is too large, the middle driving disc moves back too much, and the collision with the back friction plate will also make the clutch not completely separated.

Safety hazards: the length of the front pressure plate spring is relatively different from the stiffness or damaged, the hole depth of the spring is unequal, and the inner and outer clutch disc assembly is warped, the rivet is loose, etc., resulting in the radial circular runout of the clutch assembly and the full runout of the end face exceeds the regulations, so that it is in a state of intermittent contact. The gap between the piston and the push rod of the hydraulic cylinder of the hydraulically operated clutch is not properly adjusted.

I've encountered this problem before, and the solution is: hang a gear, press the clutch pedal and brake pedal, start the engine and it can be restored. It may be the principle that the water film sticks the clutch plate, and the two pieces of glass are glued together with water in the middle. Hope it helps!

Hang the gear in the state of turning off, find a few people to push a few meters, don't ignore, the problem can be solved and it will not hurt the motor or the car.

Thank you for your advice, my method is still very effective.

Hello, I am your exclusive technician, attentive, careful, dedicated to answering your car questions, for you to find the corresponding problem solutions and solutions! The main reason why the clutch does not separate after the vehicle wades in the water is: the separation of the collaborator plate and the pressure plate are rusty and sticky.

As a result, it can't be separated, and it can't be hung up. Solution: The first posture search, hang a gear and a gear directly under the state of ignition, and then start the road impact a few times to see if it can rush away.

This method can be tried and tested. Generally, rust sticky is not very strong and can be solved. Second, if it is parked for a few days after the water has passed, it will rust and stick very much.

Repeated impacts, can not be solved, can only remove the transmission, remove the clutch pressure plate, re-polish and install. Therefore, if you usually have a manual transmission model, do not park the car immediately after wading in the water. Drive a certain distance to let the water dry before parking!