How are GUNPLA parts made? I lost the whole waist part of my card wing

If you want to repair the entire waist, you can only buy parts to repair it.

General soil fillers are only used to fill in and repair minor defects.

Although the AB mending soil can be pinched out of shape, it is a little troublesome to knead the waist of the Gundam.

If LZ has the technology, you can try it (in fact, it will be much cheaper to buy a new waist than to use madding soil, after all, you will have to spray paint later).

Soil repair is generally a joint, fill the stealing glue If it is shaped, it will be worth the loss You don't have the original to compare with you.

And it's too high-end to make your own, I guess it's hard for you to get it right. If there is an original, it is not difficult to copy

It is recommended that you may wish to buy a domestic flying wing. I remember that the parts were generic. And the skeleton of the W series in Bandai is basically the same. Don't worry about not being able to install it when you buy it

Cut out the instruction manual and send it to Bandai.

Does the landlord need war damage or decay? If you are damaged in battle, it is really difficult to do, you must destroy the outer surface of the bright orange, and then use a painting tool to paint - if it is very difficult to do the weathering, you can wash the stains, dilute the paint, dip some with a large pen, apply it where you need it, and then gently press it on the surface with a clean napkin to make the stain more natural. However, I think Li Chen's hair loss which key Zen is still white and bright and good-looking, battle damage and aging are suitable for the UC series of bodies, and the effect of the previous weapons out of the battle damage is more shocking =-=

Go and buy a similar one, or glue it with 502, or make one yourself, and it's not difficult to make a broken part.

Haha, GUNPLA is most afraid of bear children, and this phrase has been passed down in circles for a long time.

What's going on?

If the parts are broken, the non-load-bearing place can be directly glued, the load-bearing place is piled, and the copper pillar is glued again.

If you lose the part, it is recommended to make a repair.

Also, if it's convenient, you have to beat the bear child so that he doesn't dare to have a next time, so as to prevent future troubles. Above.

There are generally spare parts for the purchase of joint link parts in the B company, but if you don't have it, ......Find a replacement, or fix it directly, it's a big deal not to move it in the future If you are lucky enough for external parts, TB has bulk sales, but you can't grit your teeth and buy a domestic one of the same model, and pull it out for use (luxury)!

The landlord did not make it clear that it was the first part, and if you have any questions, you can ask ......

Call you professional, use a pen knife to cut the broken hole flat, make a hole in it with a needle, thread the steel wire, connect it to the body, the appearance is basically invisible, see Electric Shock magazine for details.

If the pile can't be driven, you have to build it yourself.

In terms of material, plastic hot bending, or aluminum alloy + file.

It's a headache.

1. Part of the coloring (money-saving, convenient) materials: what are the differences between the comparison model and the set color such as Gundam marker, color palette, face photographer, cotton swab, etc., and use the same color to supplement the color. Where the marker tip is not available, press the pen tip to squeeze the color onto the palette, and use the face pen to color, if you feel strong, you can add some solvent appropriately.

2. All the brushes are painted and colored (the effect will be better than the local coloring, but it takes more practice to leave no brushstrokes) Materials: water-based gunpla paint, solvent (in fact, water can also be used), model paint retardant, flat pen, face pen, palette, palette stick, dropper, paper towels, etc. 1. Place parts of different colors separately. 2. Use a toning stick to put the pigment out to the palette, add solvent with a dropper, and put a delay agent appropriately (which can effectively alleviate the strokes) 3. After adjusting the color, use the pen to dip the paint in the part frame or the back of the part to check the color, and you can color.

4. The color should be thinly coated with multiple layers using the cross method, and the coating can effectively reduce the brushstrokes along the texture trend of the parts.

3. Spray gun coloring (uniform paint film, outstanding effect, high technical content, expensive cost) Materials: spray gun, air compressor (air bottle can also be used), gunpla paint spray gun, color reference table, toning stick, dropper, masking tape, foam board, bamboo stick, clip, double-sided tape, tweezers, pen knife, cutting pad, steel ruler, mask, etc. 1, classify parts of different colors 2, adjust the required color according to the color table 3, use a pen knife, steel ruler, etc. to paste the masking tape, and do the covering operation for the parts, Fix the parts on the foam board with bamboo sticks and other tools 4, pour the color into a clean spray gun, adjust it, try to spray 5, adjust it to color, spray it thinly several times (dry to spray the second layer) 6, spray back into the foam board to dry. *(Sprinkler irrigation, basically the same) Special coating.

1. Washing stain washing (the technique used for weathering can make the model look more textured and make the effect of stains) Materials: enamel paint, solvent, flat pen, paper towel 1, dilute the enamel paint with solvent, to be very thin, about 1:3, adjust it according to your needs 2, use diluted pigments to "wash" the parts in a reasonable order 3, use paper towels and other materials to absorb excess paint.

4. Place in a ventilated place to dry.

2. Dry sweeping (to make the water chestnut angle of the model more prominent, increase the three-dimensional effect, which is equivalent to adding highlights to the painting) Materials: model paint (generally white), brushes (old or waste can be), paper towels, etc. 1, dip a little paint with a paintbrush 2, wipe off the paint with a paper towel (basically leave no color) 3, gently sweep the rhombus edge of the model and other places that need to be prominent.

3. Pearl coating (let the model shine with a charming luster like pearls) Materials: pearl powder, glossy transparent paint, toning sticks, palettes, solvents, etc. 1. Pour out the pearl powder on the palette 2. Take out the transparent paint with a toning stick to adjust the pearl powder, and you can put some solvent if you think it is thick 3. Adjust evenly with a toning stick, it must be uniform, the pearl powder is easy to precipitate, 4. Spray with a spray gun.

The first time the newcomer is in the prime group, it is not recommended to buy such an expensive one, you can buy a cheap practice hand, like buying a domestic TT (high) HG or MG, and the domestic mg is only a few dozen yuan on the Internet, and this hundreds of Bandai are much cheaper, not to mention that you are a novice thing, and the knife is crooked, and the hundreds of Gundam are in the wrong place, and it is distressing.

It is recommended that you start with 1 144 hg to practice, and good component color separation can also not require too much coloring.

The tools you need to prepare (for novices) are not cheap to buy a professional pen knife, so it is recommended that you buy it this way.

Start by buying a bottle of matting nail clippers double-ended gravers (the engraved ones are cheap).

Easy assembly tutorial for beginners.

First of all, open the box, take out all the plates (some of the domestic plates are more oily, so simply soak them in soapy water overnight) and spray them with matting.

Then use nail clippers to cut out the parts, use a cutter to cut off the excess, and then you look at the instruction manual group.

The above method is not to outline the line of the prime group, and if you use a needle pen (ranging from 5 to 7 yuan) to draw a simple stroke, and then matte and color, if you can't afford professional pigments, it is recommended that you use acrylic paint, use a small oil brush to color, the effect is also very good.

In addition, you have to look at this carefully, if you are using a water-based pencil, use oil-based matting paint, and if you are oil-based, you should use water-based matting, and acrylic is considered oil-based, so it is better to use water-based.

It's cheap, let's do the math.

First of all, the main body is as high as 1 144 TT is about 30 yuan, 15 yuan online, more than 50 good matting general, 9 yuan.

Needle pen 5 yuan acrylic Mary's bottle 10 yuan z

If you want to make a Gundam, you can do it, it's a beginner's universal Gundam method, it's easy and fast, and it can achieve beautiful results at the same time.

I don't recommend the domestic ones, because novices don't know how to handle parts, and the domestic ones are inherently of poor quality, and the parts are misplaced, which is not suitable for novices. When you learn to transform, spray paint, and then do domestic.

If you don't have money, it's better to make this model, and the cost is only fifty yuan.

It's so normal! Because the model is a process of constant updating, there are new technologies and the penetration of old technologies, and manufacturers are lazy, so even some old parts that are not used are opened together.

This situation is normal, some parts are redundant, and the hand parts can be replaced, like HG's Goddess of Justice F reload, using the extra parts can be restored to the Angel Gundam, don't worry about this problem

It's clear that the height of your gray is normal, and I have a lot of leftover pc pieces now. As for the extra hand shape, it is not the same. Also, more than one piece is not normal, what are you afraid of. Fewer pieces is sad...

Isn't it normal to have more pc pieces?,A proportion of up to,PC pieces are all universal.,At most, the colors are different.。

It's normal, there will definitely be extra parts. Stickers because LEDs are now popular, so there will be a sticker that can transmit light, but some people will like the old version of the sticker, so B will make two sets of stickers for buyers to choose. PC parts will not count how much you need to use a model, and some people will not see small parts in the process of spelling, so there will be some more.

GUNPLA especially MG

Many of the models are generic, and some even have the same internal structure as the True Warrior and Turn A.

Buying a red heretic will have several pieces of the blue heresy.

Not to mention the three planes of the flying wing.

It's nice to have a lot of hands.

I still love my pitch black assault, which has a lot of different shapes, after all, the movable hand is not strong enough.

And stickers are generally stuck in the middle of nowhere.

Unless it's like Sinanju and Unicorn, spray it with cardboard for sales.

You're scared too much. It's the first time I've seen it.

If you have any more, you can keep it first. It is a lot of parts left at the time of production. I'm afraid you'll accidentally break it. And let you change it like the flying wings I just built. More than one full head one hand.

So I can change the color or take it and modify the light. How wonderful.

The extra parts are immediate. So it may be more than that.

If you have money. You can go and buy different batch numbers. Let's see if you can build another one!

The parts are all universal, it's normal to have more, and it's funny to have less...

Normal, don't worry, isn't it good to say a few more?

MG57 RX-78-2 Gundam DU

MG69 KA Edition Wing Gundam Zhi

MG76 KA Edition Iron Ball DAO

MG89 KA Edition Skeleton Gundam x1

MG102 KA version inside unicorn.

Beast Gundam MG126 V Gundam Ka Version.

MG134 V Gundam Core Tank Enhancement Set KA Edition MG135 V-DASH Gundam KA Version.

MG162 RX-93 V Gundam.

MG174 MSN-04 Sazabi.

Hi-Nu Gundam verKA (coming soon) RX-93 V Gundam Titanium Edition.

The following is a limited edition MG

Pirate Gundam x2

Pirate Gundam x3

There is also one that will be released soon.

Hi-V Gundam HWS expansion parts.