How to punch holes in the tiles on the wall, will not break

With an electric drill, as long as the tile is not hollow, it will not break.

Nowadays there is a kind of drill bit that is specially designed to punch holes in the tile.

The position of the hole to be punched is pre-calibrated to ensure the level. (Note that there should be no water and electricity lines in the corresponding position in the wall) when punching holes in the tiles with a glass drill bit, first make a pit in the direction of inclination; Otherwise, the tile is too smooth and difficult to locate; Or it's not all tiled, just make a small hole with nails; If you want to be precise, it is best to use a plate that already has holes (of the right size).

Set to make a shallow mark can remove the positioning of the orifice plate, and. Prepare a water bottle in advance, drill a hole in the cap, and fill the bottle with water. Then, when punching, the water should be moistened to the contact part of the drill bit and the tile at the same time; Especially with all tiles, there must be water.

There is no need to change the percussion drill bit. Punch through the tile part and continue to punch the screw depth. Pay attention to make a hole, remove the glass drill bit, and dredge the hollow part of the blocked drill bit. (This is especially true for full tiles).

Press the tile with your hand and use a sharper drill bit.

Drill holes with an electric hammer. You can start to turn to low speed and then drill on the surface of the tile, and then accelerate after entering, so that the tile is not easy to break.

Operation method] 1. Before starting construction, check the water and electricity road map of the previous home decoration to ensure that there are no water and electricity lines on this wall.

2. Draw the size and diameter on the wall with a pen, and then find a tile left over from the previous decoration. Draw the same diameter and drill a hole in the discarded tile first.

3. Spray some water on the wall, otherwise the temperature will rise when the eye is drilled for a while, and the tiles will be easy to crack. After spraying water, aim the hole on the waste tile to the hole on the wall, use the electric hammer to aim vertically at the point, slowly force through the tile, open a small opening, you can remove the waste tile, and then force on the wall to the appropriate depth.

4. After the hole is laid, stuff the expansion tube of about the same size into it, and then use a screwdriver to screw the basket up, and then tighten it.

If you want the tile to be perforated without cracking, you need to do it: do not punch holes in the position of the tile with hollow drums; Before punching, it is necessary to paste the sealing glue in the corresponding position; The percussion drill is horizontal with the tile punching position, and a small hole is made with a cement nail; When drilling, the speed should be controlled, not too fast; Accelerate when hitting the cement wall; Add water to the perforated area.

Before punching the tile, it is necessary to put the percussion drill at the same level as the tile punching position, and hold the percussion drill tightly to prevent it from getting off your hand when punching, so as to effectively prevent the tile from cracking. In addition, you should not use too much force to punch holes in the tiles, but wait for the tiles to be penetrated, and then increase the intensity to make deep punches.

When using a percussion drill, it is necessary to add water to the perforated position so that it can be better cooled down, and to a certain extent, it can also prevent the cracking of the tile. Before punching, you can also paste the sealing glue on the tile, which can prevent the slippage of the impact drill during the punching process, and greatly reduce the cracking of the tile.

Precautions for tiling

Before paving, the line should be played, and the reference line at right angles to the door entrance should be popped up on the ground, and the line should start from the door to ensure that the entrance is the whole brick, and the non-whole brick is placed in the dark corner or under the furniture, and the line should be popped up to control the vertical and horizontal positioning. The concrete floor should be chiseled with a depth of 5 10 mm, and the spacing of the chisel marks is about 30 mm. After that, clean the floating ash, mortar, oil stains, and produce scattered water brush to the ground.

When paving, the cement mortar should be fully smeared on the back of the ceramic floor tiles, and then compacted with a rubber after paving. At the same time, check and correct with a level to wipe the cement mortar on the surface. Before paving the ceramic floor tiles, the ceramic floor tiles should be soaked and dried.

How to punch the tile so that it will not crack the pro! Hello, I am glad to answer for you<> pro-tile punching will not crack the method is as follows: the first step: tap to check whether the tile is hollow Select a tile with a more solid paving Try to choose to punch a hole in the center of a tile Mark the position with a marker.

Step 2: How to determine that there is no water pipe and electricity behind the detection of the perforation position? The most convenient way is to look at the layout of the water and electricity, and the owners who can't find it are safest with the help of a wall detector.

Use it to scan the walls, if there are wires in the walls, an alarm will sound, and then avoid the location to punch holes. To save money and trouble, you can also take a small look at the wall and then go deeper. However, you have to think clearly, if the position of the wire is detected, this hole will inevitably affect the visual appearance.

Step 3: Once you have determined that the position is OK, seal the perforated points with a wide transparent tape in a criss-cross manner, which is very important! Very important!

Reduce the chance of tiles bursting! Step 4: Lock the position with a nail and first drill a 2 3mm small hole in the borehole with a cement nail.

This action is mainly due to the fact that the surface of the tile is too smooth, and the drill bit is easy to slip when punching, which is dangerous and may also destroy the tile! Step 5: Then, enter the drilling link and first adjust the electric drill to the flat drill mode, slowly penetrate the tiles, go to the wall part after entering, and then adjust to the hammer drill mode, so that the tiles are not easy to break.

Once the hole is ready, then stuff the screw into the hole, tighten it, and you're done! Here are a few precautions, you should remember: when punching, it is best to have a partner next to you.

Prepare a mineral water bottle with water in advance, punch a few holes with a needle on the lid (it is easier to use a lighter to heat the needle and pierce the hole), and then when you punch the hole, you can get the water to the contact between the drill bit and the tile. Because when drilling, the temperature of the drilling position will rise sharply, causing the tile to burst. Do not punch holes in the bulging areas of the tiles, as there is a gap between the tiles and the wall, which is more likely to burst.

When two holes need to be drilled and the distance is very close, it is best to plug the plastic nut tightly after the first hole is made, and then make the second hole, which can reduce the possibility of tile cracking. Hope mine can help you <>

Do you have any other questions?