Please teach PRO E how to draw a square and round entity, and how to do it in a detailed step, such

Insert Blend Extension (Default Parallel Regular Section) Point Finish Select Smooth, Point Complete Select Top Plane Point OK Point Default Sketch State Draw a circle (change the diameter to 812mm) Divide the circle into 4 segments evenly An arrow will appear as the start point and direction at a certain split point, select the point and then right-click to select the starting point to change the direction, select other points and then right-click to select the starting point, and the starting point will change. (Use the above method to set the starting point and direction) Click the right mouse button anywhere on the screen to select and switch the section (at this time, the line of the circle turns gray) Draw a rectangle 1150x458 Use the above method to set the direction and starting point to set the starting point and direction (the starting point and direction should correspond to the circle, otherwise there will be distortion) After the drawing is finished, complete the sketch Select the blind hole to complete Enter the height 780 tick Preview it, if you can, you can be sure, if it doesn't work, you are making adjustments, try it!

Created with a parallel blend feature, break the circle into four parts, noting that the start point corresponds.

The proe basic command tutorial is recommended.

The day of the stakeout of the round place.

Since the balance brother has moved to put the potato sample, the blanking diagram and the component diagram are produced.

At present, I mostly use this software.

Steel structure CAD elbows, tees and large and small heads are all available.

The world is round in sheet metal.

Drawing and lofting are slow.

It's mostly with socks.

Automatic lofting out of the lower bending mould drawing.

At the same time, the component diagram is automatically drawn.

All blanking and component dimensions are automatically annotated.

Well, this line crack slip source brigade, with the mix command, there is a variable gear wax mix in it, but the circle seems to be made into the same number of nodes as the square, I haven't used that thing for a few years, and I forgot a little bit,

Scan the solid and then convert it to get the sheet metal piece.

When drawing a square, select a starting point, remember the direction of the starting point, switch the section, when drawing a circle, use the breakpoint tool to break the circle into 4 parts, the position of the break point should be within a quadrant with the position of the square drawn before, and it cannot be interrupted directly on the coordinate system, the direction of the starting point should be the same as the direction of the starting point of the square drawn before, and then define the spacing to determine the completion of the work

Heaven quietly calls for a picture of the circle of the earth.

That is, the lofting diagram of the round sky.

At present, everyone uses this a lot.

Automatic lofting out of the blanking chart.

All blanking and component dimensions are automatically annotated.

Synchronously and automatically leak out the area of the blanking diagram to the chain.

Three open chaos through the elbow big and small head can be.

I went into the finger rock brigade and went to the town to see.

The UG round place every day is not convenient for this.

It is possible to be square or round.

In CAD.

Lofting can be easily automated in a matter of seconds.

It is still synchronous and automatic to give the area of the blanking chart.

The sky is round and the earth is still able to solve all problems with this method.

1. Draw the main view according to the size;

2. Draw a top view according to the size;

3. Divide the circumference in the top view into 12 equal parts, and connect each point with line segments according to the figure, which is equal to line 1, line 2, line 3, line 4 respectively;

4. Make a line segment equal to line 1, and do a perpendicular line.

equal to the height of the main view, and perpendicular to line 1 at point a, connecting point b to point c is equal to line segment 1; From point A, make the line segment AD equal to line 2, and connect the line segment 2 from point D to point C; AF is equal to line 3, and connecting point F to point C is equal to line segment 3; AE is equal to line 4, connecting point E to point C and other line segments 4;

The round sky is also called the round heaven place.

This type of lofting.

There are also elbow tees, large and small heads, conical tables, etc.

You can use this in CAD.

Enter the parameters to automatically generate the overall component diagram and diagram.

It also automatically gives the area of the blanking diagram synchronously.

All blanking and component dimensions are automatically annotated.

The processing diagram of the square and the earth, the blanking diagram of the round place.