The kitchen sink pipe is not blocked, but what is the reason for the poor drainage?

1. Leakage of sink drain.

If the leakage of the sink is due to the leakage of the sink drain, generally speaking, it should be the pivot washer in the sink that is damaged, and only need to replace the pivot pad with one. Use needle-nose pliers to tie the gland and rotate it, take it out after it is loosened, and use an iron clamp to remove the crushed pivot washer and replace it with a new one.

2. Water leakage in the gap under the sink bolt.

Water leakage in the gap under the sink plug may be caused by damage to the triangular gasket in the gland. At this time, you only need to use a special tool to turn the screws of the faucet, take out the screws and tether after loosening, loosen the gland and take it out, and then remove the triangular gasket in the gland and replace it with a new triangular gasket.

3. Water leakage at the junction of the sink butt.

The leakage at the joint of the sink butt may be caused by the loosening of the cap screw cap of the faucet, which can be solved immediately by tightening the cap screw cap again or replacing it with a new gasket.

4. The water pipe is brittle and leaking, and the sealing is not timely leaking.

The water pipe is embrittle, the sealing is not timely, and only the hardware needs to be replaced. When installing hardware, all kinds of residues in the pipeline must be completely eliminated to prevent the valve core from being stuck and blocked. There are some more inconvenient hardware replacements, and it is best to find a technical professional.

It is better for maintenance personnel to carry out maintenance.

5. The sewer is plugged with water leakage.

If the sewer is blocked and leaking, the dirt must be removed, but it is better to dredge it yourself or let a technical professional staff dredge it to prevent the situation from getting worse.

1. The sewer in the kitchen often contains a large amount of oil, and the grease condenses, making the inner diameter of the sewer pipe smaller, resulting in blockage and poor drainage.

2. Pipeline installation problems: there may be two traps, one has been installed in the sewer pipe, and another one is brought when the sanitary ware is installed, which is easy to cause poor drainage due to the secondary water seal. If so, remove one.

Generally, if the sewer pipe cannot be blocked, the sink drain has been checked; It should be that the downspout of the sink is raised too high to inhibit the flow of water.

The kitchen sink pipe is not blocked, why can't the water leak?

The kitchen sink pipe is not blocked, but what is the reason for the poor drainage: the kitchen sink pipe is not blocked, but the reason for the poor drain is the pipe installation problem 1, the kitchen drainage, often contains a large amount of oil, grease condensation, so that the inner diameter of the sewer pipe becomes smaller, resulting in blockage, poor drainage. 2. Pipeline installation problems:

There may be two traps, one has been installed in the sewer pipe, and another one is brought when the sanitary ware is installed, which is easy to cause poor drainage due to the secondary water seal. If so, remove one.

Summary. Hello, glad to answer for you. Kitchen drain drain poor drain solution:

Method 1: We can use caustic soda to unclog the sewer pipe, put the caustic soda into the mouth of the sewer and pour a pot of boiling water into it, or we can also use baking soda and vinegar to unclog the sewer pipe.

What to do if the kitchen drain pipe is not draining well.

Hello, glad to answer for you. Kitchen sewer drain poor drainage solution: Method 1: We can use caustic soda to dredge the sewer pipe, put caustic soda into the mouth of the sewer and pour a pot of boiling water into it, or we can also use baking soda and vinegar to unclog the sewer pipe.

Method 2: If the sewer pipe at home is blocked by oil, you can use boiling water, if you can buy concentrated sulfuric acid, the effect is better, but we still need to be cautious in order to ensure the safety of life. Method 3:

For example, we can also go to the market to buy a spring steel wire of about 2 meters, and then bend 10-20 degrees at the top of 1-2 cm, and dredge the water back and forth at the entrance and exit of the sewer with water, so that a good dredging effect can also be achieved. Method 4: If the pipe blockage is not serious, pour a large spoonful of laundry detergent into the sewer pipe first, and then pour 3 cups of hot water.

If this does not clear the sewer, pour vinegar into it, which can slightly soften the stain, so as to achieve the purpose of unclogging the sewer pipe.

1. If it is a blockage caused by food residues falling into the sewer S bend, you should directly take out the food residues blocked inside, and then go to the hardware store to buy a wire dredger, and go deep into the pipe to take out the blocked food residues.

2. If it is clogged by oil, the water pipe of the sink should be pumped out first, and then the dredging agent should be poured into the sewer, and then about 800 ml of warm water should be poured in, and then the warm water test can be dredged.

1. What should I do if the kitchen sewer is blocked?

1. If the food residue falls into the sewer S bend, it is easy to cause blockage after a long time, the solution is very simple, directly take out the food residue blocked inside, it is recommended to go to the hardware store to buy a wire dredger, go deep into the pipe to take out the blocked food residue, and the pipe will be dredged.

2. There is no effect on the use of pipeline dredging device for oil blockage, at this time, a professional dredging agent should be used, which is generally sold in supermarkets, and the use method is also very simple: first pump out the water pipe of the sink, then pour the dredging agent into the sewer, and then pour about 800 ml of warm water, wait for about an hour, and then test it with warm water.

3. If you feel that the above method is too troublesome, there is a strong way to drain - use a dredging artifact, since it is a dredging artifact, it can solve any blockage problem, and it is also equipped with different plugs, whether it is a kitchen, floor drain, or toilet, it has its own exclusive plug. How to use: Before dredging, dig holes with newspapers and cover the water surface, so that the water splash will not splash around when dredging, if the dredging is not successful, it may be that the air pressure is too small, increase the air pressure and try again.

However, it is best not to exceed six pressures when inflating, and it is best not to use it more than ten times in a row.

2. What should I do if the kitchen drain is blocked?

1. It is easier to clean the oil stains on the bowl with hot water than with cold water. For non-serious sewer blockages, we can also use the same principle, using boiling water to flush the sewer, that is, using hot water to melt the oil remaining on the sewer pipe wall. Prepare enough boiling water (it is recommended to prepare a full pot of boiling water), and keep it prudent to fill the drain continuously.

2. We all know that the chemical name of baking soda is sodium bicarbonate. Sodium bicarbonate is alkaline when dissolved in water, while the oil esters in oil stains are hydrolyzed under alkaline conditions. Take an appropriate amount of baking soda and pour it into a pot filled with hot water, and pour the baking soda into the drain continuously and slowly; You can also pour baking soda directly into the sewer, dissolve the baking soda with the water in the sewer, and after a few minutes, after the baking soda and the oil ester of the sewer have fully reacted, pour it with boiling water, and it will basically be dredged.

3. If the method of boiling water and baking soda still cannot dredge the sewer or the dredging result is not ideal, you can also choose to buy a special pipe dredging agent, which is sold in supermarkets and various shopping malls. This is because there are a variety of ingredients in these special dredging agents that dissolve the oil.

<> "What to do if the kitchen sink drain pipe is clogged.

2. Let's take a look at what blocks the kitchen sink, usually the kitchen sewer pipe is mostly blocked by the U-shaped bend, if it is a sewer pipe with sewage screws, it is simple, unscrew it directly, but it is best to put a sewage basin at the bottom before treatment to avoid staining the cabinet. After unscrewing, use a wire to pass both sides through, and it usually solves the problem quickly. If it has not been disposed of, you may wish to disassemble all the sewer pipes, unscrew and wash all the plastic connections, and remove the internal impurities before installing them, which can be done in no more than 30 minutes.

3. Usually, the sewer pipes at home are blocked by oil, so first pour a pot of boiling water into the sewer pipe, and then use hooks and other tools to reach into the drain pipe to clean up the dirt blocked in it. If you live on the first floor, check the outdoor sewer for fallen leaves or silt that could cause the drain to become clogged.

4. When there is no obvious blockage in the sewer pipe of the sink, you can use a wet cloth to plug the overflow hole, and then use a pinch to clean up the sediment.

5. If you can't clear the debris of the sink sewer pipe with a pickpocket, you can put a bucket in the trap of the drain pipe, and then unscrew the elbow to clean up the internal blockage.

6. If the above methods are not feasible, it means that the debris that causes the drainage pipe to be blocked is in the depths of the pipeline, and it is necessary to find a professional maintenance and grinding personnel or company in time to dredge it to avoid long-term blockage and water accumulation in the pool.

After reading the above introduction, I have a further understanding of what to do if the kitchen sink sewer pipe is blocked.