How to install the system after assembling the computer yourself? windws7 is good under detailed ope

The trial version is free, and you can write the system image in a USB drive. Plug in the USB drive directly and you can go in and install the system, and follow the prompts step by step. After the system is done, install the official driver directly.

How do I reinstall the system directly on my computer? Most users will use a USB flash drive when reinstalling the system, but there are also users who feel that the USB flash drive is too troublesome or even have no USB flash drive. It's actually possible.

As long as the current system can still be used normally, you can reinstall the system directly on the computer through the ** operating system. Here is an example of reinstalling the cracked version of windows7 to teach you how to reinstall the system directly on the computer.

Installation Instructions:1Direct reinstallation is only applicable to computers with the current system installed and the system can be used normally, otherwise you need to reinstall the CD or USB flash drive.

2.If it is a ghost system, reinstall it as described in this article. If it is the original system, reinstall it with an NT6 HDD.

3.If the pre-installed Win8 Win10 model is pre-installed, it is not recommended to reinstall the system directly from the hard disk, but to use a USB flash drive.

The steps to reinstall the system directly on your computer are as follows.

1.Convert the system ISO archive file to a partition other than the C drive, such as the F drive, right-click, and use WinRAR and other tools to extract it to the current folder or the specified folder. It cannot be extracted to the C drive and desktop, otherwise it cannot be installed;

2.A dialog box pops up to perform the decompression process of the system's ISO compression shed. It takes a few minutes;

3.After unzipping, we open the installation directory and find [Installer;

4.Double-click Collapse and Trapped [Install] to open this installation interface, select [Restore System], select the file as the image file path, and check the location of the C drive to be installed. If the C drive is not displayed, judge the C drive according to the volume label or capacity, then check [Restart after execution], and finally click [Execute].

5.A prompt box pops up, prompting that the image file is about to be restored to partition C, click OK to continue;

6.At this point, the computer will restart and you will be taken to this interface. By default, the sysceo recovery project is selected to start;

7.Start to enter this interface, format the C drive, it will take 3-5 minutes to install the system to the C drive.

8.After the above execution is completed, it will automatically restart and enter the interface to perform the system driver installation and configuration process.

9.The reinstallation process lasts 5-10 minutes. Finally, start to enter the new system desktop, and the system is reinstalled.

That how to reinstall the system directly on the computer. If the system can be used normally, the system can be reinstalled directly. It's very simple.

Heart of Kings 2 click to play

Just reinstall the system (win10) directly, and it is recommended to use a USB flash drive to complete the reinstallation system.

Activate your current windows7 is best professional or flagship version,Pony windows activation tool can be activated,On this basis, upgrade and install windows10,U disk,Unzip the image,Or virtual optical drive,Engraved disk can be,So that it will be automatically activated directly after installation,No matter how you install windows10 in the future, it will be automatically activated。

Hello. Five ways to install the system:

(1) Make a USB flash drive boot disk installation system

(2) Install the system with a hard disk installer

(3) Install the system with a disc

(4) ISO system file click: setup to install the system

(5) Use a ghost installer. exe to install the system

If the system can be turned on and entered, the system can be installed by any of the above methods;

If you cannot boot the computer into the system, you can use (1) or (3) of the above methods to install the system.

Install win7 without a CD-ROM drive! U Disk System Tutorial.

1. Extract the ISO image of Windows 7 to the D disk with UltraISO (such as D: Win7, the following will be an example with this path), UltraISO extraction method: first open the ISO file in the software, and then click "Extract" in the "Operation" column.

2. Copy the bootmgr file and boot folder in the win7 directory to the root directory of the C drive, prepare the files for the upcoming Windows 7 boot, and create a new sources folder in the root directory of the C drive.

3. Copy the extracted D: Win7 Sources file to the Sources folder just created on the C drive.

4. Enter cmd in the "Run" of the Windows XP start menu, and then enter C: Boot NT60 C: in the pop-up command line, and press Enter, prompting successful means that the boot boot boot has been repaired successfully (the boot right is transferred to the boot file of Windows 7).

5. Close the COMMAND window and restart the computer, it will automatically enter the Windows 7 installation interface, select the installation language, set the time and keyboard, etc.

6. "Start Installation Interface" appears, Siqi specially reminds you not to click "Install Now" here, but click "Repair Computer" in the lower left corner to enter"System Recovery Options"and select the last item"Command prompt"to enter the DOS window.

7. Enter D: Win7 Sources in the DOS window and press Enter to start installing Windows 7.

8. Select the language and keyboard settings, format the C drive, and start installing Windows 7

The next Kingsoft reload master can reinstall the computer system!

The recent trend is to use the rainforest wood wind USB flash drive boot disk for one-click installation.

Lin Mufeng U disk to start the production tool" -- insert the U disk according to the prompts -- start making -- and the production will be completed in one minute.

Rainforest wood wind U disk startup disk one-click installation main steps:

Step 2: Use the rain forest wood wind U disk system software to make a boot USB flash drive Step 4: Enter the BIOS to set the boot sequence of the USB flash drive (this step can be skipped, you can press the F12 key or F8 key or ESC key to select the USB flash drive to start at the time of booting.)

Step 5: Use the USB flash drive to start the quick installation system.

One-click installation, just follow the prompts and click the mouse.

The detailed tutorial can be learned on the official website of the rainforest wood wind USB flash drive, or you can ask the technician of the official website for computer technology.