What should I do if the IP address of Tengda router and gateway are displayed as 0

The IP address and gateway of the Tengda router are displayed as 0, indicating that the router has not successfully dialed up to connect to the network.

Solution: 1. Check whether the router is connected correctly.

2. Check whether the bandwidth and password entered by the router are normal.

If your router cannot be connected to the network after setting, please log in to the router interface, click "Advanced Settings" - "System Status" to check the WAN status and connection status, please check the following troubleshooting methods according to the router WAN connection status:

1.Hard boot the router and see if it solves the problem.

Whether the router route can be passed.

3.Hit ** to consult customer service.

In this case, you must first confirm the username and password you set in the router, enter the router settings interface, quickly set --adsl virtual dialing, reconfirm the password of your username and then restart the router, System Tools - Restart the router. That's absolutely fine.

You look for the port on the router to do a factory reset to see if it must be your problem with the settings.

The best thing to do is to hard start, and mine has a lot of problems.

Hello pro Tengda router has obtained a valid IP address but cannot access the Internet The reason may be a problem with the broadband itself or a problem with the router, and the solution is as follows. 1. First open the browser on the computer, and then enter the default router IP address in the browser address bar. 2. Next, the login interface of the router will pop up, enter the router and password here, and then click the login button.

3. Next, on the main interface of the router that opens, click the "Advanced Settings" tab in the upper right corner. 4. Next, in the advanced settings page of the router that opens, click the "Intranet Settings" menu item. 5. In the intranet setting menu item, find the "LAN port setting" menu item.

6. Finally, the LAN port setting page will be opened in the right page, enter the new LAN port IP address here, and finally click the save button, and the router will take effect after restarting.

Summary. Hello, dear.

Unplug the router, restart the router, plug the router back in about five seconds, and wait for the router to start up normally to check whether the computer can access the Internet.

I wish you a happy life and a beautiful mood!

Hello, unplug the power of the router, restart the router, plug the router back in about five seconds, wait for the router to start normally, check if the computer can go online, I wish you a happy life!

Tried it and it didn't work.

If you can't access the Internet after restarting the router, see if the IP address is automatically obtained, if not, you can change it to automatically obtain it.

Don't worry about this, you can change the IP address to get it automatically.

The Baiip address displayed in the router is the IP address assigned by the DHCP server of the router DUs, not the Internet DAOIP address. It can be dedicated through a computer.

Direct connection dial-up to test whether the broadband account can connect to the Internet normally.

Tool: Computer.

The steps to connect the computer broadband account and password are as follows:

1. Right-click the small icon of the computer in the lower right corner and select "Open Network and Internet Settings";

2. Select "Dial";

3. Select "Set up a new connection";

4. Select "Connect to Internet";

5. Select "Set up a new connection";

6. Select "Broadband (PPPOE)";

7. Enter the broadband account password;

8. Click "Connect", if the connection is successful, there is no problem with the external network broadband and you need to reset the router, if the connection fails, it is the external network broadband failure, and you need to contact the operator for maintenance.

1. Open the "Control Panel" and double-click the "Network Connection" item to enter.

2. Right-click "Local Connection" and select "Properties" from the pop-up menu.

3. In the "Local Connection Properties" window that opens, double-click the "Internet Protocol (IPv4)" item.

4. Manually specify the DNS address in the window that opens.

5. In the router management interface, click on the "DHCP Service" item.

6. Select "Enable DHCP Service" on the right side.

1. First of all, plug in the power supply. At this time, the indicator light will turn on. Then connect your WAN port with broadband. Inside.

2. Use your computer or other capacity.

3. Select the connection method, it is recommended to choose "automatic selection", most people should be pppoe.

4. Enter the network account and password given to you by ** business. Click Next.

5. Then set your Wi-Fi name and password.

6. Finally, restart the router.

It should be a DNS error. Wireless.

Router DNS Configuration Method:

1. Enter the IP address of the router in the address bar of the browser (the zhi on the label behind the router), and enter the login username and password to enter the settings page.

2. In the running state, we need to see our current DNS here. Search the local DNS address of the broadband operator you are using online to see if it is the same, if not, you need to change it.

4. Just tick the button to set up the DNS server, and then enter the DNS address of the local broadband operator you use.

If there is no network signal, it may be that the WAN port of the router is set up in the wrong way to access the Internet, and the WAN port is not connected to the external network; It may also be that the DHCP service of the router is not enabled; It may be that the LAN port needs to be set to automatically obtain IP addresses. Check the status of the connector connected to the network cable and the indicator of the router, and the indicator of the interface corresponding to the data will flash.

Supplement: [Handling common faults of wireless networks].

1. Check whether the wireless router has power saving mode enabled. In power-saving mode, the transmit power of the antenna will drop significantly, which will directly lead to the attenuation of the wireless signal, which will affect the wireless rate.

2. Check if there is any obstacle between the two wireless devices, especially metal objects. Metal objects can seriously affect the transmission of wireless signals. The wireless device can be placed high and the coverage of the signal will be greater.

3. Check whether there are electromagnetic interference equipment in the room, such as microwave ovens, cordless **, etc. If several devices have similar wireless frequencies, it can interfere with the transmission of other wireless devices. Most microwave ovens use 7-11channel on the frequency band.

Therefore, you can change the transmission channel of the wireless router to 14channel.

4. Router performance. The routing function of ADSL modem is limited, and it is usually impossible for a device that nominally connects 5 clients to provide normal connection sharing services to 20 clients. It is recommended to replace a broadband router with better performance as well.

5. Line quality. ADSL has high requirements for line quality, if the line is far away from the operator, there is a relatively large electromagnetic interference in the middle, which will have an impact on the transmission of signals.

2.Try changing the last bit of the IP address!

3.Look at your machine with two networks, one is connected and the other is getting an IPConnect to the .you're usingTake a look at which other connection is disabled in your network connection properties!

4.It's as if you also have a network card, or a virtual network card.

The computer or mobile phone specifies that the IP is in the same segment as the IP of the active network, and the gateway uses the IP address of the Internet connection.

Hello, glad for your question, this case should be a dns error. Wireless router DNS configuration method: 1. Enter the IP address of the router in the browser address bar (on the label behind the router), and enter the login username and password to enter the settings page.

2. In the running state, we need to see our current DNS here. Search the local DNS address of the broadband operator you are using online to see if it is the same, if not, you need to change it. 3. More settings in "Network Parameters" on the left, and then you can see the "WAN Port Settings" option, and select "Advanced Settings".

4. Just tick the button to set up the DNS server, and then enter the DNS address of the local broadband operator you use.

Questions. <>

Here's how my phone should work.

This situation may also be caused by IP address conflict, that is, there are too many nearby users, resulting in network congestion, it is recommended that you first switch to static Internet access, fill in an IP at will, and then save, wait a while, and then switch to dynamic, cycle switching several times, until you get a usable IP, you can look at the connection icon in the lower right corner of the computer, you can go online immediately after getting a usable IP, or change to a new mobile phone to operate, I hope it can help you.

Just clone a Mac and select the default MAC address.

If the broadband is normal, then the only thing is that the route is set up incorrectly.

What device was before routing.

1. Check whether the WAN light of the router is on, if the light is not on.

1.Unplug the power cable behind the router and reconnect it again, find a small hole or small button marked reset near the router's Internet cable interface, press it for about ten seconds when the router is powered on, and observe that the indicator light turns on and off together and then lets go.

Try unplugging the broadband line from the routing WAN port, connect the broadband line to any one of the 1 2 3 interfaces, if the 1 2 3 light is not on, you can change the WAN port line connected to the router.

2.If the 1 2 3 interface light is on, try to take a network cable One end is connected to the computer and the other end is connected to the routing WAN port See if the light of the WAN port is on, if it is not lit, it may be a fault of the routing WAN port, and it is recommended to send it for inspection.

If it is on, it means that there is no problem with the WAN interface, open the browser to enter, click "Advanced Settings" - WAN Rate Control, select 10M half-duplex for bandwidth below 4M, select 10M full-duplex for 4-10m, select 100M half-duplex for 10m-20m, select 100M full-duplex for 20-100m, and click OK. Click on System Tools - Restart Router.

Second, if the wan light is on.

A normal version of a 300m router.

Enter, click Advanced Settings - WAN port media type, see if you select "Wireless WAN", if so, change to "Wired WAN" and click OK.