If the Internet access is set up for the two machine interconnection machine A is routed through ma

What do you do with dual network cards when you have a router?

It should be a machine, a b machine, and Internet equipment are all plugged into the router.

Then the router uses the default.

A and B are IPs:

Default gateway. Subnet mask.

That's it, both machines can access the Internet and be interconnected.

If it's a mobile phone, click Forget or delete this network in the wireless settings, and then re-enter the password to connect.

You can see the shared hard drive, which means that there is no problem with the network.

1. Check the firewall of the notebook, whether it is set to off, not please set it off 2. Cancel the shared hard disk and share it again.

3. Then try to start -- run --- input.

Computer name or IP address

For example: server or

Hello, your situation may be because the firewall of your laptop is not turned off (including the windows built-in), resulting in access on the one hand, and can not be accessed on the other, please refer to the specific LAN sharing:

Note: You also need to turn off the firewall, this kind of software is very convenient for users who are not familiar with LAN sharing, and do not have to worry about the security of LAN sharing.

It must have been set up somewhere, under a router, a laptop can, and a desktop must be able to.

1.Check the network card settings on your laptop and desktop first. Make sure that both machines are on the same network segment2The hard disk on which the file resides has the permission to view and read.

3. The NMS can be set to the address of the other party.

4. Whether the firewall can communicate.

PPOE dial-up was not successful, and the WAN port was not connected, so I couldn't access the Internet. Please check that the router is connected to the broadband modem before, if there is no problem, it may be a broadband problem, and it should be repaired.

Your router's WAN port does not have a cable connected to it.

You need to connect a cable from the modem to the WAN port of the router so that you can dial up.

In addition, you should choose the connection mode to: Auto Connect, which connects automatically after power on and disconnection. Now the default is an on-demand connection, see it.

1. Select Auto Connect.

2. Then click on the connection, if it is more than ten times and it is not possible to check the line, you can ask questions.

Reset the router to factory settings, reconnect the router to the modem, and then re-enter the Internet password, if it still doesn't work, restore the computer and the router with one click, and then connect.

The router is not set up, check the bottom to automatically connect, the latest free event.

Fan Wen Navigation Station.

It should be your wrong online account or password.

Look at the red words at the bottom,It's the WAN port is not connected,First check if the cat can work normally,If it can work normally,Then check the connection between the router and the cat,

The WAN port is not connected. Check whether the network cable (port access) is correct.

It may be a virus.

Factory reset your router and set it up again.

Computer antivirus.

Unplugged the desktop If the WAN port does not flash, it means that the desktop is likely to be poisoned

In the web page enter ** where your route is generally is.

The login username and password of the router that has not been set are admin, and after entering, select Automatically obtain IP in the setup wizard.

If you are using a hub, then you had better ask your network service provider if two computers are allowed to log in to the network at the same time with the same account. I used to use the hub on two computers at the same time, so there was no problem. I guess the key is whether the service provider allows this kind of Internet access.

You have to check the IP address of the router itself, such as: or, etc., and then set the IP address of one of the computers to the same paragraph, such as: etc., and connect with the router, enter the IP address of the router in the IE address bar and enter the entry will appear a login interface (if the settings are correct), enter the account name and password to enter the routing setting interface (the account name and password are generally written in the manual, generally:

admin, the same is true for the password), enter your account name and Internet password in the routing wizard settings, save and log out, all computers can access the Internet as long as they are connected to other interfaces of the router, if not, you can restart the modem and router,

Aipu is very likely to be bound by Aipu It means that Aipu has bound your broadband to the computer MAC that has just dialed up for the first time, and you have to call ** to unbind Aipu, or connect the computer with the router Internet cable to clone the Mac in the router.

This requires you to call the ** (962525) manual service to the Aipu broadband customer service, tell her that you are going to use the router to access the Internet now, and ask her to help you unbind the client over there.

How did you set it up, can you add one?

Based on your description, I can only judge that your company already has a main router, and yours is used to expand the network.

Then Lianfa is:

Incoming cable - the LAN port of the router.

Settings: Go to the router and disable the DHCP function.

The LAN port of the computer --- router.

This can complete the expansion of the network.

You said that I have experienced this problem, in fact, the main problem is that you have to configure it in the router, and you must write the physical address of your computer network card into the router. Because the company has set up a MAK address binding, so that you can connect to the Internet.

It seems that you can directly connect your network cable to the computer and you can access the Internet. The router is an account and password provided by the network operator, and after it is set up, it does not need to dial up, and it can directly access the Internet and can be divided into several computers to access the Internet at the same time.

To access the Internet through a route, your gateway should point to the address of the route, for example, and your DNS should point to the public DNS in the route