Why can t I see the components after the mold is turned after the dawn is turned?

You can't see its structure, mainly because your steps are faulty, you should follow his procedure to turn the mold little by little, and you can see it after turning the mold.

It's because the two of them should be different with modules, so if you renovate it, then its overall structure will be better, so you won't be able to see it.

Why can't I see the rebuttal component after parting? It may be due to some of the situations that have arisen after the distribution, that is, it has not yet manifested itself except for some of the things that followed.

You can let it turn over the fine decoration of the deep pit hotel and see if it can be produced. On the other hand, the calculation work is originally the bottom of the industry.

Why can't I see the component analysis behind my door after these templates? After flipping through it, you will verify the pattern of the home, and you will not be able to see its component graphics after it is broken.

Not only can it be used for civil engineering, steel bar, installation of all professional takeoff software, but also provides tools for turning mold and rapid modeling, which feels great, the interface is very friendly, and the operation is easy to use

We can't see the valuation after subcontracting, so you can look at some news on the Internet, or focus on some of the situation of this store.

Why can't I see the components behind the model after the dawn is turned over? I think that after the mold is turned, it will be turned over, and of course I can't look at the components after the mold turning.

You can't see this kind of molded build, so you can look at it from the middle of the manual.

What about after the tin is turned? I can't see the components after the mother, because he hasn't sent a full version yet.

It's just because he changed the dry film again.

Not only can it be used for civil engineering, steel bar, installation of all professional takeoff software, but also provides tools for turning mold and rapid modeling, which feels great, the interface is very friendly, and the operation is easy to use

Turning the mold: I used to use the olive mountain turning mold before, but now I think it is very cumbersome, and I also need to do a lot of processing on the drawings in CAD to try the dawn.

After turning the mold, directly import the segmented CAD drawing link into the software floor plan, quickly identify the layer for conversion, the accuracy is very high, and the calculation quantity: secondary components (rings, lintels, window sills), foundation cushions, earthwork, and room decoration can be intelligently and quickly automatically arranged in a solid state, which is very good. Moreover, the report imitates the process of manual calculation, which is convenient for our cost personnel to fry chicken.

Adjustment tools: My favorite tool is the tool for view sectioning and component visibility, which is quite trouble-free and solves my trouble of vvving and adjusting the view range in modeling.

Reinforcement arrangement: The reinforcement is arranged by inputting the reinforcement information, which solves the cumbersome manual arrangement.

Slice mold or sheet mold operation method: the vacuum of silicone is applied by brushing or pouring method. If you are making a sheet mold or slicing mold and use the brushing method, first apply a layer of release agent or release agent to the product or model you want to copy before painting, and then apply the silicone to the product (Note:

Be sure to apply evenly) After waiting for 30 minutes, paste a layer of gauze or fiberglass cloth on the surface to increase the strength, and then apply a second layer of silicone, and wait for the silicone to dry, and then make an outer mold, which can use materials such as plaster or resin.

The operation method of the filling mold or infusion mold: the filling mold or infusion mold is used for relatively smooth or simple products, that is, the product or model you want to copy, surrounded by rubber plates or glass plates, and pour the vacuum silicone directly into the product, after the silicone is dried and formed, take out the product, and the mold will be formed (Note: the infusion mold is generally made of silica gel with relatively soft hardness, so that the demoulding is easier and will not damage the product in the silicone mold), the above is the whole process of the use and operation of the silicone mold.

Because in the process of making the mold, in order to reduce the viscosity of the silica gel and make the silica gel easy to operate, a large amount of silicone oil is added to the silica gel, which will make the silica gel very soft, resulting in the phenomenon of no tensile resistance, reduced tear strength and poor tensile force, resulting in the phenomenon that the mold is not durable, the service life is short, and the number of mold turning is less.

The mold silicone itself will not be oily, and the oil is because of the addition of composite silicone oil (a compound and ligand of silicone oil and white mineral oil) during the operation, because white mineral oil is a petrochemical product, not silicone oil. This phenomenon occurs because the product or model to be copied has not been sanded or polished. Because the model or product itself is actually not smooth or perfect enough, if the product or model to be copied is not polished or polished, no matter how good the mold made of silicone isolated, it will not be beautiful and smooth enough.

In another case, when the mold release agent is applied, it will cause the mold to be unsmooth if it is not evenly applied.

If the silica gel is not damaged, it can be restored, just remove the hard layer, soak in hot water and it's fine, but the removal effect will not be very good, it is recommended to apply some oil to the silica gel next time you do the mold.

Take the prototype and prepare the casting mold.

There is a gap between the two wings of the prototype, which is concave inward, extending to the bottom, and it must be filled with plastic clay, otherwise it will never be opened again after the mold is solidified.

The hollow at the bottom is also plugged, otherwise the gypsum will be poured into the hollow prototype, which will also cause the mold to not be formed.

Place the prototype in it, leaving gaps on the bottom and around the surface to keep the mold walls thick and avoid holes.

Note: Before putting it in, make sure that the box does not leak, not at all, and the good gypsum slurry is very fluid. The box should be able to withstand soaking, I can't do this, and then I changed to a big bottle, cut it, and then that one was very good.

The parting agent is applied on the inner wall of the box and the prototype, some are sold, and it can also be replaced with very thick soapy water, and it is necessary to achieve the application, and strive to solidify into a thin layer of tissue before casting, if it is wet, the parting surface will be very blurry after casting, and the things that come out are very rough. Cast.

First silica gel is used as the outer film, and then turned with glass fiber reinforced plastic, but the cost is high.

It's called Bubu, Korean. It's not a teddy bear, it's brown.

The BJD materials sold outside are all resin, but the prototype of each BJD at the beginning is not resin, and must first be molded by a humanoid with something similar to Ladoll that can be molded, and then turned into a mold for mass production. We can only use LADOLL to make our own BJD, and if we are satisfied, we can also find a place where we can turn the resin mold and turn a few more. After all, resin is much stronger than clay, and the surface is smooth and not afraid of water.

If you want to turn the mold yourself, it is more difficult, because there are vacuum bubble removal machines in professional mold turning places, and the machine is very expensive, and it is not improper to buy it for mass production. If you don't use that machine, it will be covered with bubbles and even potholes on the surface. So I think the steps should be to buy ladoll first and do it yourself, and if you can really do it to the extent that you are satisfied, then find a manufacturer or workshop that can turn the mold.

You can turn it over, you can not turn it, but after a long time (at most a few years) the lime clay will crack, so you need to turn the mold. There are generally two kinds of molds, and the steel mold used by the figure factory is used, but this is generally mass production, and the cost is too high, so it is generally turned with silicone. The mold is probably turned with AB water, silicone, oil sludge, release paste, as well as building blocks for molding, of course, electronic scales, water and soil supplementation.

If possible, you can also use a vacuum machine. After that, the gray mold must be painted, and this hand painting must at least buy paint, generally using the Japanese Tamiya, gunshi. There are three kinds, water-splitting, oil-based, enamel paint, non-hand painting and airbrush, turtle pump or something.

1. Stir the silica gel and the curing agent evenly. The appearance of the mold silicone is a flowing liquid, component A is silica gel, and component B is a curing agent. Example:

Take 100 grams of silica gel and add 2 grams of curing agent (Note: Silicone and curing agent must be stirred evenly, if there is no stirring evenly, the mold will appear a piece has been cured, a piece has not been cured, and the silica gel will appear dry and solidified unevenly, which will affect the service life of the silicone mold and the number of mold turning, and even cause the mold to be scrapped.

2. Vacuum exhaust bubble treatment: after the silica gel and the curing agent are stirred evenly, the vacuum bubble process is carried out, the vacuum time should not be too long, under normal circumstances, do not exceed ten minutes, the vacuum time is too long, the silica gel is cured immediately, resulting in a cross-linking reaction, so that the silica gel becomes a piece by piece, and can not be painted or injected, so that the silica gel is wasted, and the silica gel can only be poured into the trash can and the silica gel is taken again.

3. Painting or operation process: the silicone that has been evacuated and discharged through the bubbles is brushed or perfused. Pour on top of the product (Note:

Before pouring silicone, the product or model to be copied must be injected with a release agent or release agent). Then the silicone is brushed on the product, the brushing must be even, and a layer of gauze fiber weft cloth is pasted after 30 minutes to increase the strength and tensile force of the silicone. Then apply a layer of silicone, and paste a layer of gauze fiber weft cloth, so that after two times, it is OK.

Only in this way, the service life and the number of mold turning of the silicone mold can be relatively improved, which can save costs and improve efficiency.

4. The production of the outer mold: the general method and material used is to surround the mold, enclose it with rubber board or wooden board, one uses gypsum to fill the mold cabinet, and the other uses resin to paint the way, paint a layer of resin to paste a layer of fiberglass cloth, and then paint and paste, and repeatedly two or three layers can complete the mold outer mold.

5. The operation method of filling mold or pouring mold: filling mold or pouring mold is used for relatively smooth or simple products, no mold line saves labor and time, that is, the product or model you want to copy, surrounded by rubber plate or glass plate, and the silicone that has been pumped through the vacuum is poured directly into the product, and after the silicone is dried and formed, the product is taken out, and the mold is formed (note: the casting mold is generally made of silica gel with soft hardness, so that the demoulding is easier and will not damage the product in the silicone mold).