How to pass, how to turn on, how to operate after booting

If you are a new user, please read this article carefully before turning on the computer for the first time, and follow the following professional operations to configure the system for the first boot of the computer, so that you can experience a relaxing journey of opening up the new computer.

1. Please connect the computer and adapter before turning on the computer.

Be sure to connect the power adapter to your computer before pressing the computer power button to turn it on.

1. If your computer is a notebook, then the battery is in "transport mode" by default, at this time, if you press the power button directly, the computer will not have any response, you need to connect the power adapter to the computer before it can turn on normally.

2. If your computer is a desktop, in addition to confirming that the power cable is connected normally, you also need to confirm whether the connection position between the display signal cable and the host graphics card is correct. 2. System configuration after the computer is turned on for the first time.

If your computer is pre-installed with Windows 10 (hereinafter referred to as Win10) operating system, please follow the normal steps to configure the system for the first boot.

If your computer is a desktop, in addition to confirming that the power cable is connected normally, you also need to make sure that the signal cable of the monitor is connected to the host graphics card in the correct position.

What is it and how to operate after booting? When you ask questions in the future, please be specific, or upload**.

After turning on the phone, you can use the screen of the mobile phone to swipe it open.

Solution 1: You can turn off the power first, open the computer case, dial out the memory stick, use the eraser to wipe the part of the gold finger (that is, where there is a copper sheet) back and forth a few times, and then insert a memory slot back, and you're good to go.

Solution 2: Press F8 without stopping at boot, enter Advanced, select the last correct configuration, and confirm.

Solution 3: It is a bad sector on the hard disk, when the computer reads the bad sector, it is stuck, the background is still running, the CPU occupancy is immediately very high, and then the blue screen, processing method: under normal circumstances, it is repaired with HDD, if it can't be repaired, it can only be replaced with a hard disk.

Solution 4: It's because of illegal shutdown, such as power outage, forced shutdown, or sudden crash, after turning on, it will be self-checked, and it is also a blue screen. It may waste a little time, but it must read it by itself, because this is the process of checking the disk by the hard disk, and generally the first time it has been read, it will not appear next time.

Don't stop with ESC, or you'll have a blue screen next time, do it all over again. If you want to self-test every day, you have to start --- chkntfs t:

0", the general problem is solved.

Before doing the above, it is best to restore the BIOS of the motherboard to the factory value, or you can discharge the motherboard battery, that is, remove the battery, wait for 20 seconds and then install it back, or connect the jumper to two or three, which is conducive to eliminating strange phenomena caused by the disorder of the motherboard BIOS.

The above four methods can't be solved, please reinstall the system.

If the hard drive fails, the system needs to run a disk check, and you let it check well, and it won't be like this when you turn it on again.

The reason for this is an ungraced shutdown (software not exiting or being bumped).

Now it's hard disk self-test, just wait, it should be caused by forced shutdown.

Do you keep repeating these lines when the time is up? This should be a system self-check, you wait for the time to run out and then take a look, or you reinstall the system, this may be you repaired the hard drive, the system files are corrupted.

Redo the system Besides, don't you turn it on, I look like I'm in the hard drive self-test, if it can't be turned on, then redo the system.

Try again after shutting down, but not find after-sales or professionals.

Restart, if it doesn't work, fix it.

Just wait a while, I've been in this situation as well.

Hello, it is recommended that you check whether the system is crashed or errored. If so, you need to flash the machine. (Flashing is risky, not recommended).

Check if there is a problem with the hardware, and if so, you need to send it back to the factory for repair.

Check if it is caused by third-party software or if there is a system malfunction or a malfunction of accessories such as batteries. We recommend trying the following:

1) The battery has no power or is insufficient, please charge it for half an hour and then press the power button to see if it can be turned on;

2) If the OPPO phone can't be turned on, you can press and hold the power button and the volume + button at the same time to force restart the phone, and it can return to normal after restarting;

3) If it still stays on the boot screen after restarting, you can try to restore your phone to factory settings to solve the problem; Pull out the phone battery to power off and turn it off, then install the battery, press and hold the volume and power keys at the same time, enter the recovery mode, and then select Chinese Simplified - Clear Data - Clear all data, and then restart the phone, it can return to normal;

4) If you still can't enter the system after restarting after clearing all data, you can connect to the computer to flash the phone, and flash the new system for the phone.

5) If conditions permit, replace the charger, data cable and battery (detachable mobile phone) and turn it on after charging for half an hour.

If this appears, it means that your motherboard's CMOS battery is dead, or there is a problem with the wiring between the battery and the IO and the south bridge.

Under normal circumstances, press F1 to enter the system; Press F2 or Del to enter the BIOS, change the time to the current date, and optimize the saving.

Optimizing BIOS, some are F9 (or F7), F10 saves and exits.

I don't know what the subject is talking about.,What kind of boot is it? Is it because the phone won't turn on? Or the computer won't turn on

1, if the phone can not be turned on, first check whether the phone has power, no power, first charge, if it still can't be turned on after charging, then your mobile phone system has a problem, you may need to flash the phone to enter, the corresponding mobile phone rom on the Internet, **after, and then** related mobile phone flash software installation, and then follow the prompts step by step to flash the machine, in fact, it is very simple, the information point is good.

2.If the computer can't turn on, you have many reasons, such as the case power supply, the boot button of the case, the computer's graphics card problems, memory problems, computer system problems, all of which may cause the computer to fail to turn on.

1. If there is a backup, then use one-click restore or ghost to restore the backup.

2. If there is no backup, then reinstall the system.

If the boot file is lost, restore the system if you have a backup, and repair or reinstall it if you don't!

You can only reinstall the system, and you can only boot it from the optical drive.

1. Take iPhone6 as an example, first press and hold the power button of the phone until the following boot screen appears, and then slide the red box to select the content to enter the next setting.

2. In this interface, select the language as Chinese Simplified and enter the next step of settings.

3. Select the country as China, and go to the next step.

4. According to personal habits, select the required keyboard input method and enter the next step of setting.

5. Complete the wireless LAN setting and enter the next step of setting.

6. Select whether to enable location services and enter the next step of settings.

7. Choose to set Touch ID, or you can choose to set it up later.

8. Set whether to restore data to iPhone, and then you can complete the phone activation settings.