Where can I learn the vitrified brick adhesive technology

1.Alkali. Gram!

Tile adhesive, the third generation of ceramic tile paving materials, broke the problem of vitrified tiles, antique bricks, microcrystalline stone and marble and other materials with very low water absorption, scrape a layer on the back of the tile, the dosage is, and then directly on the cement mortar, immediately on the wall paving, no need to wait for dry, convenient construction, simple and fast, the effect is very good.

In July 2015, the state issued a national invention patent certificate, the technology is the most advanced in the industry, and the rest are all counterfeits. Each barrel is provided with a warranty contract, and the warranty is 20 years, so that consumers have no worries

4..Current paving materials include cement mortar, tile adhesive, one-component adhesive and alkali. Gram!

Tile adhesive, cement mortar and tile adhesive, brick drop phenomenon is common; One-component adhesive (emulsion), cumbersome construction, need to wait for drying, tiles to be stacked layer by layer, a few hours of drying time seriously affect the construction period and waste of time, and afraid of staining ash and water.

Alkali. Gram! Tile adhesive perfectly solves all the above problems, ** is not very expensive and the cost performance is quite high

Go to Henan, such as Xinyang Shenghua Chemical has been producing for 28 years, has rich experience, and has purchased a machine to teach the formula.

It's best to find such a powerful manufacturer to give you advice.

How to use the vitrified brick adhesive has always been a concern for many technicians, and it is a piece of cake for Xinyang Shenghua Chemical to do this, after all, it has been a teaching staff for 28 years.

Some friends don't know how to use vitrified brick adhesive, let's introduce it below.

When using vitrified brick adhesive, the emulsion and powder should be mixed in the correct proportion, and the electric stirrer should be used to stir evenly.

When mixing, you can't feel the ingredients, which will cause uneven mixing, and manual mixing is not allowed, which is easy to appear starch ball.

When using vitrified brick adhesive, if it is a small vitrified brick, the state potato can be used to brush and brush the way, and the point coating method can not be taken by the sail scale.

When the vitrified brick is painted, it should be spread as much as possible, not to leave space in the middle, and to leave a little gap when it is on the wall.

Nowadays, the construction of home decoration people will also be particularly trouble-free, especially when the tile is pasted, it is also replaced by glue cement, its construction cost is not high, and the effect of decoration is also very good in the long run. Vitrified glue also has great advantages, but people who have not used it also know very little. Let's take a look at it with usVitrified brick backing glueWhat are the advantages?

1. What are the advantages of vitrified brick backing adhesive?

1. For such a material, the bonding strength is high, and a new rough surface can be formed on the bonding surface of the vitrified brick, which should be known to enhance the bonding ability between the material and the bond; Good flexibility, small hardening shrinkage, strong compatibility with cement-based adhesive materials, and firm bonding; There is a certain anti-seepage performance; Freeze-thaw resistance, long-term care and long life, excellent acid and alkali resistance and anti-corrosion performance.

2. During construction, the construction is convenient, the cost is low, the net is not damaged, and the time and labor are saved; It is good to choose it, it is non-toxic and harmless, green and environmentally friendly. Base surface cleaning: Wipe the back lifting surface of the vitrified brick with a damp cloth before brushing to remove the oil stains, protective agents, release agents and other substances that affect the bonding on the back of the facing bricks.

Preparation of materials and tools: Preparation of materials: Yangtai vitrified brick adhesive (YT-302), liquid components and powder components, tools, electric mixers, tools.

Second, how to construct the vitrified brick adhesive.

1. First of all, the material is mixed: it is very important to pour the vitrified brick adhesive into the container according to the mixing ratio of water-cement ratio, and use an electric mixer to fully mix it, without corn starch ball, and the construction can be carried out after standing for 5 10 minutes. When applying adhesive backing, the method of brushing or rolling coating can be adopted.

It is recommended to use a brush and roller to evenly apply the evenly mixed adhesive to the back of the facing brick"Criss-cross method"Apply a layer evenly, generally in a dosage of about.

2. Secondly, it is to wait for more than 5 hours, and the next construction process can be carried out only after the adhesive is completely dry and solidified. During the construction period and within 24 hours of completion, the base and ambient temperature should be 5 35, and the materials that have just been constructed should be avoided within 24 hours. This product shall not be diluted with water and mixed with any other substances, and the mixed materials shall be used up within 4 hours, and shall not be mixed and used again after overtime.

After the construction is completed, maintenance and protection work should be done to prevent pollution, collision and damage. In case of eye contact, this product should be treated with medical attention in time. This product should be stored in a cool and dry environment for about 6 months.

3. In addition, the vitrified bricks with smaller coating specifications of the adhesive slurry can be brushed with row brushes, which is also a good method, but it is not advisable to do so based on the thin and dot coating method. In the picture on the right below, the ratio is obviously wrong, the powder is too little, and the application is too thin and uneven. This is a "masterpiece" of workers who are lazy to save trouble, which greatly reduces the role of adhesive backing, and should be eliminated in construction.

This will greatly reduce the effect of the vitrified brick adhesive, and the uncoated parts are still easy to hollow, and once the hollowing will produce destructive force, there will be a lot of raw flour balls.

1. Mixing of vitrified brick adhesive. The correct method is to mix it according to the emulsion and powder provided, which is also mixed with an electric mixer.

It is wrong not to mix it with sensations, as it will also cause unevenness. If you're using a handmade mixture, you won't be able to mix the ingredients well, and there's a good chance you'll have a lot of corn dough.

2. Brushing of adhesive slurry. For example, some vitrified tiles with smaller specifications can be brushed with row brushes, but if they are too thin and dot coated, this kind of painting will not work.

3. If there is too little powder in the mixing, it may lead to too thin and uneven application. This is a "masterpiece" of workers who are lazy to save trouble, and it can be said that this is also a great reduction in the role of adhesive, and this method can not be taken in construction.

4. If you are using the dot coating method, then only part of the drawing on both ends of the brick, this practice is to save materials. However, it can be said that this method is also greatly reduced, and the unpainted parts are still easy to hollow, and it may also increase the destructive power, or even double, and appear empty.

5. For the bricks that have just been coated with the slurry, you must remember not to stack them together, nor to put them in the sun or shower, and remember to put them indoors and stand against the wall. At the same time, it is necessary to pay attention to the gasket sandwiched between the bricks, so as to prevent each other from sticking to each other, and also facilitate ventilation and drying.

6. Apply adhesive. The adhesive must be full of pulp, and the middle should not be left empty, or it will not affect the overall effect. There must be brick joints on the wall of vitrified bricks, otherwise the expansion and contraction stress caused by temperature changes may not be released.

The adhesive is a new material, so the method must be correct when using, so that the overall effect will not be affected in the process of use.

Vitrified tile adhesive is now a very widely used auxiliary material, which can effectively improve the bond strength between the back of the stone and the adhesive material, and avoid problems such as hollowing and falling off of the tile. When it comes to vitrified brick adhesive, you may be relatively unfamiliar, the following little old editor will briefly talk about how to use vitrified tile adhesive and the content of the ceramic tile adhesive brand, let's take a look!

How to use vitrified tile adhesive.

1. Clean the base surface.

Before painting, you need to wipe the back of the vitrified tile with a damp cloth, in order to remove the stains, protective agent, release agent, etc. on the back of the Huai trapped tile.

2. Mix the materials.

Then pour the vitrified brick adhesive into the container according to the mix ratio of 1:, and then fully mix with the electric mixer until there is no corn starch ball, and the construction can be carried out after standing for 5 10 minutes.

3. Brush the adhesive backing.

Brushing adhesive is relatively simple, usually using the method of brushing or roller coating, using a brush or roller to paint the adhesive on the back of the brick, pay attention to be sure to evenly paint, to avoid missing the bottom.

After painting, you need to wait for 5 hours for the tile adhesive brand recommendation.

1. Bostik.

Founded in 1889, the Bostik brand is owned by Total and is one of the world's largest producers of adhesives and sealants. Since its creation, the brand has been committed to products such as industrial, construction and civil adhesives, which are favored and liked by everyone.

2. Sika. Sika is a glue company with very good strength and reputation, and is also one of the world's leading manufacturers of construction chemicals and a multinational company in the production of global chemical materials.

3, the Terrible. Rayty adhesive is a well-known enterprise from the United States, which has a history of several decades and is one of the world's ceramic tile and stone manufacturers. The brand not only has advanced production technology, but also has an excellent production team to produce high-quality Qin Minsheng products.

4. JCDecaux. JCDecaux brand I believe you are very familiar with, it is a waterproof enterprise under the PALI Group, the main products are K11 waterproof paste, TTB tile adhesive and tile caulk products, to provide users with the most exquisite service.

5. Mapei. Mapei is a waterproof company from Italy, as well as a manufacturer of construction adhesives and sealants, and enjoys a high reputation in the waterproof coating industry. Summary:

When decorating a house, we all know that it is inseparable from ceramic tiles, and when we use ceramic tiles, we all value quality. When we use it, many people know that it is inseparable from the adhesive. So what do we need to pay attention to when we know the vitrified brick adhesive?

Let's take a look at the use of vitrified tile adhesive and precautions for use!

How to use vitrified brick adhesive.

1. Wipe the back of the vitrified brick with a damp cloth before brushing to remove the oil, protectant, release agent and other substances that affect the bonding on the back of the facing brick.

2. Preparation of materials and tools: Materials are prepared for Yangtai vitrified brick adhesive (YT-302), liquid components and powder components, tools, electric mixers, brushes, rollers and other tools.

3. Material mixing: pour the vitrified brick adhesive into the container according to the water-cement ratio of about 1:, use an electric mixer to fully mix it, there is no corn starch ball, and the construction can be carried out after standing for 5 10 minutes.

4. Brushing adhesive: During construction, the method of brushing or rolling coating can be adopted. Use a brush and roller to evenly coat the mixed adhesive on the back of the facing brick, and it is recommended to use the "cross method" to evenly paint a layer to avoid leakage of coating.

bottom, the general dosage is about. After more than 5 hours, the adhesive is completely dry before the next construction process can be carried out.

5. Vitrified tiles with smaller specifications can be brushed with row brushes, but it is not advisable to be too thin and dot coated. Obviously, the ratio is wrong, the powder is too little, and the application is too thin and uneven. This is a "masterpiece" of workers who are lazy to save trouble, which greatly reduces the role of adhesive backing, and should be eliminated in construction.

6. The dot coating method is adopted, and only part of the drawing is made at both ends of the brick, in order to save materials. Doing so will greatly reduce the effect of the vitrified brick adhesive, and the uncoated parts are still easy to hollow, and once the hollowing will produce destructive force, and then threaten the parts coated with adhesive. Because of the destructive force of the vitrified bricks, Kai Hongda, or even doubled, will also be empty together.

Precautions for the use of vitrified tile adhesive.

1.The mixed slurry needs to be used up within 2 hours, and it cannot be reused after drying.

2.The construction temperature is between 5 -40.

3.It is strictly forbidden to add other materials during the batching process.

4.After each construction, clean the tools and mechanical equipment in time.

5.If it accidentally falls into the eye during construction, it can be rinsed with water in time.

When we decorate, we need to understand the precautions when the vitrified tile is glued, and it is also very important to learn how to use it. The above is the introduction of the vitrified brick adhesive use method and precautions for use, and this is the end of it.

Vitrified brick adhesive (JQ-B201) is a two-component product composed of imported high-quality polymer emulsion material and inorganic silicate, which is specially used for the back treatment of wet vitrified bricks and low water absorption hard bricks, so as to improve the bond strength between the bricks and the adhesive materials, and effectively solve the common hollowing and falling off problems in the wet paste of vitrified tiles.

Its characteristics and main technical parameters.

1. The bonding strength is high, and a new bonding surface can be formed on the back of the vitrified brick to enhance the bonding ability between the bonding materials.

2. Good flexibility, small hardening shrinkage, strong compatibility with cement-based adhesive materials, and firm bonding; Excellent acid and alkali resistance and anti-corrosion properties.

3. Convenient construction and easy control; Non-toxic, harmless, green and environmentally friendly.