The hand is stained with the glue of 502, what is the best way to get it open

What should I do if my hand is stuck with 502 glue? Don't worry, just drop a drop, and the glue will melt in 2 seconds without hurting your hands.

It can be washed off with alcoholic liquids such as rosin perfume, liquor, and toilet water, and I have tried it. It is better to have a higher concentration.

Soak in hot water, soak for a while and then it will fall. The next time you apply skin cream to your hands, it won't get sticky.

It will fall off naturally after a while.

When this happens, don't panic at first, and don't pull hard, so as not to cause secondary damage to **.

If the 502 glue has not completely solidified on the hands, you can rinse it with clean water, after rinsing for a few minutes, the 502 glue will become solid, and then wash it with hand sanitizer to remove it. If the 502 glue on your hands has completely solidified, you can soak the water in hot water for about 15-20 minutes, and the 502 glue will slowly soften.

In addition, organic solvents can be used to dissolve 502 glue, and professional detanglers can also be bought at present, only need to drip an appropriate amount of organic solvent or debilitant on the adhesive place, and 502 glue can be removed. After removal, it is recommended that you apply hand cream to the affected area to protect**.

If the 502 glue is pasted for a long time, half an hour or even more than an hour, the 502 glue has been air-dried, and you can apply wind oil, gasoline or even alcohol and other handles to soak these substances into these substances, which generally lasts for a few minutes, and the 502 glue may also be actively dissolved. In the process of removing the glue, remember not to pull or pull hard, which may cause damage to the hand.

502 glue is afraid of water, it can be removed by soaking it in water a little, don't pull it when it's dry, it's easy to destroy**.

1. Soapy water: Prepare hot water first, then pour some soapy water into it, put your hands stained with 502 glue into the hot water, and after soaking for 5 minutes, you will find that the glue has become soft.

2. Wind oil essence: drop the wind oil essence on the place where the 502 glue is glued to the congratulatory belt, and then rub your hands back and forth a few times, you will find that the glue has been melted by the wind oil essence.

3. Nail remover: Nail remover is also useful for 502 glue, which can dissolve nail messy water. Just apply nail polish remover to the area where 502 is sticking and rub it slowly a few times to free your fingers.

If it doesn't work all at once, use more nail polish and wipe it a few times until the glue dissolves.

4. Alcohol: Of course, it will be more effective to use a special cleaning agent for 502 glue. However, when there is no cleaning agent, you can try to clean with alcohol, apply alcohol to the glue, and after a few minutes, remove the traces of the glue.

However, this method is harmful to ** and is not recommended for children.

We inevitably need to use 502 glue in life, but what should we do if we accidentally stick our hands when using it? Here are a few tips that might help you.

Method 1:Use the hardness of the glue to burn and destroy.

502 glue is very hard after drying, this feature is an advantage and a disadvantage, the advantage is that it can be a good glue to harder objects, but some of the greater flexibility often has no long-term effect, that is to say, the bonding is very good at the beginning, and the glue will be opened after a period of time. When your two fingers are glued together, rub the glue between your fingers vigorously to loosen the glue. Rub it for a while and try to see if you can separate your fingers.

Method 2:Blister with water.

This method is relatively simple, that is, when the glue has just dripped on your hand and has not dried, quickly put Duan Liang's fingers into the cold water, soak it for a few minutes and you can see that the glue has become a solid, and then buckle the glue off your hand. If the glue has dried on the hand, it will not be effective to use water again, so the timing must be good.

Method 3:Dissolution method.

In fact, there is no 502 that can be completely dissolved, and it can only be softened slightly, for example, the insulating oil can play a softening role, and it can be quickly rubbed off after softening. Some people say that with acetone, it is highly toxic and should not be used lightly. Apply the insulating oil in the transformer to the glue with the cover pour, and the cured 502 glue will soon become soft, and then it can be rubbed off.

If you use 502 a lot for your job, you can apply flour or powder particles such as foundation to your hands in advance or wear gloves. But if the gloves are rubber, plastic, 502 may undergo a chemical reaction that causes the gloves to melt, and the release of heat may burn your hands.

The stickiness of 502 glue is very strong, so we can use 502 glue to stick after some things break in life, but when the glue drips onto the fingers, due to the strong stickiness, it is easy to stick the fingers together, which is very annoying, and some solutions are introduced below.

01 If conditions permit, you can take a little insulating oil from the transformer, and then apply the insulating oil to the place where 502 is adhesed, which can quickly soften the dry and hard parts of 502.

02 502 glue due to its own characteristics, it will become hard after drying, we stick things to this effect, the same fingers can also be used to solve this problem after the fingers are sticky, before the glue becomes dry and hard, quickly rub the glue between the two fingers, the purpose is to make the glue slightly looser, and the fingers can be separated after rubbing for a while, but there will still be dry and hard 502 glue on the **.

03 Before 502 drops onto the fingers and has not become dry and hard, we can quickly find a basin of cold water, and then put the fingers in the cold water to soak, after soaking for a while, 502 will become solid after it is dry and hard, at this time we can slowly tear off these solids little by little, but be sure to tap it, otherwise the skin of the fingers will be torn off.

04 If you accidentally touch a little bit of paper after sticking to 502 on your fingers, it's best not to try to tear it off, because more or less paper will remain, if you have enough patience, you can leave it alone, generally after a day or two, the glue will automatically fall off, and it will not have any impact on daily life, but the fingers are a little uncomfortable.

05 The method of processing 502 is that it can be softened, after softening 502, it is very convenient to process it, if conditions permit, you can use gasoline to soften, and after softening, you can quickly rub it off by hand, it needs to be noted that acetone can not be used for operation, it is toxic.

01 After using 502 glue, we can use flour and other granular substances to smear our hands first, and after applying, we can avoid fingers being stuck when using 502 glue, this is because if there are these powdery particles on our hands, the glue will only stick to these particles on the fingers, and the stickiness to ** is not so great.

02 Wearing gloves can effectively prevent 502 from contacting fingers, but it is still necessary to classify others, such as some rubber or plastic gloves, which will melt after contacting 502, and melting will release heat, which will cause injury to the hand, so it is best to wear cotton gloves, 502 will be absorbed by the cotton directly after dropping.

03 The simplest, most convenient and fast way is to wet your fingers, after your fingers become wet, if 502 touches your fingers, it will quickly become solid, so that it will not directly touch ** and cause injury.