Watch What to do if the mechanical watch is on the fast side 15265

1. First confirm whether the deviation is stable, that is, how many seconds faster per day? Whether this value is consistent every 24 hours. If the fast value is stable, there is no major problem with the movement.

2. There are generally adjusting screws next to the hairspring, please adjust B, don't move A, because there are infinite models of the movement, and you didn't say anything about LZ.

3. If the landlord doesn't know anything, it's better to transfer it to the official after-sales service. The speed and stability of the movement can be checked by special equipment, rather than "more than 1 minute error per day" as described by the landlord.

4. The person downstairs, you feel that the error in 24 hours is more than 60 seconds, which is also called"It's fine"？？！

Fortunately, the pursuit of perfection is equivalent to not being able to get along with yourself.

There are three main reasons why mechanical watches are inaccurate.

1.Watch magnetization: The watch is in too much contact with items with magnetic fields, which leads to the phenomenon of magnetization of the watch, causing the watch to be inaccurate.

After being magnetized, the watch may stop, slow, or fast. After the watch is magnetized, its magnetism will not recede on its own, and it needs to be demagnetized to restore it to normal.

2.Lack of maintenance: If the watch lacks maintenance, it will lead to wear and tear of parts, dry up the sludge, affect the normal running time of the watch, and make the watch appear fast and slow.

3.Mechanical failures: Mechanical failures such as watch balance spring failures, escapement failures, and component slips can cause the watch to be fast and slow.

Mechanical watches are sometimes fast and sometimes slow, and it may be caused by severe impacts, water ingress, etc. Quartz watches are generally very accurate and less prone to time failures. In the case of adequate maintenance, it is more likely to be fast and slow, which is more related to the failure of the circuit board, or the poor contact of a certain part.

Here's how to solve the problem of fast running time of mechanical watches1. The handle in the middle is screwed like a screw, according to the waterproof design of the counter, when adjusting the time, it is twisted downwards counterclockwise, and it is unscrewed like a teacup lid. (If you have purchased a new watch or have not worn it for a long time, please put it on the clockwork 30 times before you wear it again, so as to ensure the energy of the watch, which is usually not needed).

3. Pull it lightly, it is 1 gear to twist up to adjust the week, and down to adjust the calendar.

4. When pulling it, it is 2 gears that can adjust the time.

How to maintain a mechanical watch:

Mechanical watches with movement watches require an appropriate amount of activity in order to continue to be on the bar. Try not to swim with your watch on, do your laundry. If you accidentally get wet, you should not pull out the watch handle to adjust the watch, but wipe it off immediately, let alone touch the seawater.

Even if the waterproof watch is indicated, it can only have a year's waterproof guarantee, because the waterproof ring of the watch will be tired after a whole year of wear and tear, plus sweat, dust and other inevitable external factors, so it must be replaced with a new waterproof ring after one year, otherwise it will not have the function of waterproofing. Because the handle head is more protruding, try to avoid it being bumped, and pay attention to the gap between the handle head and the case, too small will affect the operation, and too much will affect the waterproof performance, but also unsightly.

Fully automatic mechanical watch.

Go faster and faster workaround:

1. The automatic mechanical watch is going faster and faster to the place where it was purchased to find a merchant for maintenance.

2. Go to the merchant to ask for a new watch.

The reason why fully automatic mechanical watches are going faster and faster:

1. The speed of the mechanical watch is mainly determined by the pendulum frequency, usually the larger the pendulum amplitude, the smaller the pendulum frequency, and the smaller the pendulum amplitude, the greater the pendulum frequency.

2. The structural problem itself, due to the gravitational force of the earth, the offset between the horizontal position and the vertical position will produce a displacement, and the clockwork will be blocked.

From tightening to relaxation, the torque is unbalanced.

3. The effect of the magnetic field, after the hairspring is magnetized, the circle between the rings is only shown when wearing, there is a sticky or short-lived lap, especially in the façade, the hairspring will hang down due to its own Jane Hu Jian's redo Bili, the shaking of the arm will intensify its radial movement, and the magnetic energy utility is shown because of this.

4. The balance of the balance wheel and the balance spring, especially the balance wheel, the balance wheel is very bad, which will cause the balance wheel to highlight the precision of the surface under a certain swing. Fluctuation.

Mechanical watchesThe reasons for going fast are as follows:

1. Structural reasons. Because of the structure of the watch itself, due to the gravitational pull of the earth, the offset between the horizontal position and the vertical position will produce a displacement, clockwork.

From tightening to relaxation, the torque is unbalanced, and in addition, it is affected by external temperature, magnetic field, vibration, etc., mechanical watches.

Even if the frequency is increased a little more, it is impossible to achieve the accuracy of a quartz electronic watch.

2. The movement is magnetized. Because it is magnetized, after the hairspring is magnetized when it meets the magnetism, the circle between the rings is only shown when it is worn, and there will be sticky or short-term laps, especially on the façade, the hairspring will hang down due to its own gravity, and the shaking of the arm will exacerbate its radial movement, and the magnetic utility is shown because of this.

3. There is a problem with the pendulum frequency of the mechanical watch. Because of the problem of the swing frequency of the mechanical watch, the speed of the mechanical watch is mainly determined by the swing frequency of the mechanical watch. In general, the larger the swing, the smaller the swing frequency, and the smaller the swing, the larger the swing frequency.

Generally, mechanical watches rely on the retraction and release of the hairspring to control the swing, which is the basic principle of adjusting the speed and slowness. By making the retractable hairspring shorter, the swing will be reduced, the frequency will be larger, and the watch will be faster.