What to do if the Jaeger LeCoultre mechanical watch goes fast, what to do if the Jaeger LeCoultre me

The mechanical watch suddenly goes fast, basically caused by the following 4 reasons, no need to worry, timely to a professional watch maintenance organization for maintenance. Hope it helps.

First, the hairspring is stretched and retracted in the work, when the moment of extension, it happens to encounter the external impact force, the hairspring is affected by the external force, and the outer ring of the hairspring may be hung on the outer clamp of the fast and slow needle, or the outer pile pin of the movable outer pile ring, so that the working length of the hairspring becomes shorter, and the time is accelerated.

2. After the hairspring is shocked by external force, it may also make the fast and slow needle rotate and displace, and the working length changes.

3. Newly bought watches or watches that have been cleaned and oiled for a short time, due to excessive oil injection or improper injection, oil loss will be caused by excessive oil injection or improper injection, which will make the hairspring partially sticky and shorten the working length.

Fourth, working or entering and exiting near a large magnetic field, over a long period of time, the hairspring and other parts will be magnetized and put together with each other, and the final result is to cause the watch to stop completely.

For the handling of mechanical watches, demagnetization is the first priority, and it must be neat and thorough demagnetization; Then check the position error of the watch, continue to check the hairspring, clean the hairspring with alcohol, it will be more fuel and tidy, volatile is good, and the low-quality fuel and magnetic field will make the hairspring show up to circle or attract each other. It is best to do a timekeeping quiz on the repaired watch, and it is best to do a long-term dynamic check to see which all-round rotating experimental rack is to be put on, or to wear it directly to check carefully. If it is a deeply hidden problem, we can only detect it with the help of relevant instruments.

Treatment: 1. When there are scratches or slight scratches on the watch mirror, you can drop one or two drops of water on the watch mirror, then squeeze a little toothpaste, and then wipe it back and forth with a cotton ball to remove the scratches and make the watch glass as new.

2. If it is serious, you can polish it.

3. Find an official after-sales service center.

The watch maintenance center is located in Room 3705, 37th Floor, Block 2, Ganghui Henglong Plaza, No. 3 Hongqiao Road, Xuhui District, Shanghai 021-80184899

The mechanical watch goes fast first because the position error of the watch is relatively large, for example, the precision of the hand surface and the face is different, the error of the façade luck is relatively large, when worn, its comprehensive uniform daily error is relatively increased, the position error is a key indicator of the performance of the watch, and the general change index should be as small as possible.

There is also a common problem with the fast movement of mechanical watches, that is, the secondary outer ring of the hairspring rubs against the outer pile of the hairspring, which is also displayed on the façade and dynamics, especially if the watch has been touched before, and the hairspring is most likely to be in trouble after deformation; This sub-position, depending on what kind of movement, if it is a general ETA men's watch movement, it is easier to display the left or upper position of the watch on the wrist, this situation requires the adjustment of the gap between the secondary outer ring of the hairspring and the outer pile of the hairspring, and there should be a reasonable and safe distance between them.

If you have any questions, please feel free to send me a private message.

Common reasons why the watch goes fast:

1.The oscillator is bumped, causing the watch to go faster;

2.The hairspring rubs against the fast and slow clamp or the outer pile, causing the watch to malfunction and the watch to go fast;

3.Wearing a mechanical watch has been subjected to a violent impact or excessive exercise, resulting in the failure of the mechanical watch;

4.The watch is magnetized when it comes into contact with a strong magnetic field such as a computer or refrigerator;

5.Improper maintenance caused the watch movement to lose oil, which accelerated the wear and tear of the shaft.

Automatic watches, the power of the self-winding movement is generated by the weight of the oscillating weight in the movement, which is driven by the swing of the arm wearing the watch.

The rotor rotates, and at the same time drives the mainspring in the watch to wind the watch and push the time.

Many people have encountered the situation that the mechanical watch is not gone, some people may habitually take a few pictures of the watch, and some may shake a few times, in fact, these.

It's all the wrong thing to do.

Mechanical watches are generally composed of hundreds and thousands of parts, and the internal parts are very precise and complex, and some parts are only magnified several times.

It is the size of a human hair, so when you shoot the watch, or when you shake it, you may damage the internal parts of the mechanical watch.

In fact, there are many reasons why mechanical watches do not go, such as: there are bumps, movement gears are misaligned, the watch is magnetized, the sludge is dried for a long time, etc., big.

There are two kinds of body, the first is because of insufficient kinetic energy. The second is due to a malfunction of the mechanical watch.

Our mechanical watches often have the situation that the time is not accurate, and most people wonder if the mechanical watch is broken. There are many reasons why a mechanical watch can be parked, but there are several main reasons.

1. Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. In particular, automatic watches require more arm movement, and the winding efficiency is very low. If you usually exercise a little bit, you can wind it manually, which can ensure enough kinetic energy.

2. Gear failure: Gear train failure such as deviation wheel and center wheel failure will lead to the condition of stealing stop of the watch. These situations are often not easy to detect and require disassembly, careful inspection and testing to find out the problem and solve the problem.

3. Lack of maintenance: mechanical watches should be maintained every 2-3 years or so. If it is not maintained for a long time, a large amount of oil sludge will be generated inside. Friction between gears increases, causing slippage.

There will be after-sales ** on your warranty link, call after-sales ** to inquire about the after-sales address.

Answer the reason why the watch won't go:

The main core gear is misaligned, the watch is magnetized, bumped, and the oil sludge is dried for a long time. The most common reason for the failure of the watch not going is the lack of power of the watch and the movement of the watch does not work.

When the mechanical watch suddenly stops, the priority is to think about whether it is caused by lack of power. Hand-wound watches should be wound at the same time every day as much as possible so that the watch can operate with sufficient energy for the next 24 hours.

When the quartz watch stops, it is necessary to consider whether it is caused by the battery failure, and go to the after-sales service to replace the battery.

If the watch is used for a long time, then its wear and tear will be more serious, and the external maintenance of the watch will be easily damaged. It is necessary to regularly replace the watch you are wearing, and it is necessary to maintain the watch regularly, for the service life of your watch, it is better to maintain it regularly.

The more common reason may be a lack of kinetic energy, but some friends may say that I buy a fully automatic mechanical watch, and I don't need to wind it myself. In fact, this is a big misunderstanding, automatic mechanical watches do not need to be wound manually, but to keep the mechanical watch on the hand to wear at least 8 hours of time, because the automatic mechanical watch is the use of the arbitrary swing of the rotor to wind up, and the rotor is swinging with the movement of the arm, so if the mechanical watch needs to be worn on the hand often.

But what if you wear it on your hand a lot and don't leave? Don't worry, it may be a lack of kinetic energy, and then we need to manually wind the clockwork.

After passing the above methods, what should I do if I also find that the machine is not gone? Here we can rule out the reason for the lack of kinetic energy of the mechanical watch, it should be that the mechanical watch is faulty, if you are not a watch professional, it is best not to disassemble it rashly, please send it to a professional watch repairer for repair. Before the watch bar talked about the maintenance method of mechanical watches, mechanical watches need more maintenance than quartz watches, here is an emphasis on the maintenance methods of mechanical watches:

1.If it is a manual mechanical watch, the mechanical watch should be wound regularly, and it is recommended to wind the mechanical watch around 8 pm.

2.Automatic watches, such as insufficient arm movement, need to manually wind the watch, and the rotation of the crown needs to be controlled within 20 turns.

3.If an automatic watch has not been worn for more than 40 hours, it is necessary to turn the crown twenty times to activate the movement's drive system.

4.Regardless of the water resistance of the watch, it should be avoided as much as possible, and if it does, wipe it dry and make sure that the crown is locked at all times. It is best to replace the waterproof ring once a year.

What should I do if the mechanical watch is gone? We need to establish the common sense of protection of mechanical watches in ordinary times, and when we encounter the situation that we can't go, we don't need to worry, and we can eliminate them one by one according to the above methods, which are usually caused by insufficient kinetic energy.

There are roughly two types of situations in which the mechanical watch does not go:

1. Insufficient kinetic energy: The fully automatic mechanical watch operates by the automatic winding mechanism that can tighten the mainspring when the rotor rotates in any direction. Only when the watch is worn on the hand, the rotor rotates to generate energy as the arm moves.

Generally, a fully automatic watch should be worn on the hand for more than 8 hours a day to replenish the mainspring. Therefore, if you do not wear it for a long time, or if you do not exercise enough after wearing it, it will also cause the mechanical watch to not go. In such cases, manual winding can be used.

2. Mechanical watch failure: it needs to be sent to a professional maintenance personnel for repair. Remember not to talk about mechanical watch disassembly yourself.

Mechanical watches are driven by mechanical gears and clocksprings, and friction is inevitable when turning, so it is necessary to add oil and lubrication over time to reduce the wear rate of parts. It is advisable to inspect mechanical watches annually for improper use or water ingress. For example, sweat, rain and dirty air accumulate for many years, causing slow erosion to machinery, and the frequency and degree of damage are much higher than those in Europe, America and Japan, so regular inspection is very important; Then it needs to be thoroughly cleaned and maintained every three years.

Common reasons why the watch does not go:

1. Insufficient power reserve of the watch: You need to check whether the power of your Piaget watch is sufficient, if the amount of movement of the self-winding mechanical watch is small, it may also cause insufficient power reserve, you can supplement the power by manual winding, and then observe whether there is a phenomenon of fast and slow.

2. The watch has been hit or impacted: Piaget watches are very precise, if Piaget watches are hit or beaten, it may cause loose damage to internal parts, and it may also cause timekeeping problems. At this time, it is necessary to deal with it in time.

3. The lack of oil in the movement of the watch or the wear and aging of the internal parts may cause the problem of running time, which needs to be sent to the Piaget service center for maintenance services.

In addition to the above common situations, the watch is affected by some ambient temperatures: if the balance spring of the watch is magnetized, the watch will not be accurate.

Hello may be insufficient power Oh need to be manually wound Generally, the normal winding takes 30 times, which is basically full, (provided that you want to be full) The watch on your hand actually doesn't matter, as long as you keep it up until you can't turn it, the mainspring is full.

For automatic watches, because most automatic watches can be wound by hand, especially when worn for the first time or after stopping, you need to start the winding with your hand first. (It is recommended that you do not rely on the rotor to wind the full string at the beginning) everyone also knows that because the automatic watch is "not up to the string", it is recommended that the number of winding times of the automatic watch should be more than less, and you may wish to put a few more, such as up to 40 times, it is basically guaranteed to be full.

If the watch gets into the water, don't be in a hurry first, don't dry the battery or a hair dryer as soon as the water gets in, you need to deal with it according to the situation. There are mainly the following ways to deal with it:

If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating.

You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours.

If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts. If the water ingress is serious, it is best to go to a professional repair center for inspection.

First of all, check whether the clockwork is out of energy, if not for this reason, then there is a high probability that you need to find an after-sales or offline maintenance point for testing.

What to do if the watch doesn't go:

In fact, there are many reasons why mechanical watches do not go, such as: bumps, movement gear misalignment, magnetization of the watch, shelving for a long time, sludge drying, etc., generally divided into two kinds, the first is because of insufficient kinetic energy. The second is due to a malfunction of the mechanical watch.

Therefore, don't panic too much when you find that the mechanical watch is not leaving, and first distinguish which kind of big one it belongs to.

If you have any questions, please feel free to send me a private message.

Hello, glad to answer for you.

There are many parts inside a mechanical watch that are made of steel, such as a hairspring, large and small steel wheels, screws, bearings, and escape wheels, which are easily magnetized by magnets, magnetic fields, etc.

The speed of a watch is controlled by a hairspring, one of the most magnetized parts, and a balance wheel.

Jaeger-LeCoultre watches suddenly do not go may be because: lack of kinetic energy, lack of maintenance, gear failure, etc., it is recommended to go to a regular after-sales center to let a professional technician help you test it, it is not recommended that you go to some small repair points to avoid secondary damage to your watch, but also to avoid causing you some unnecessary trouble, the following is the Jaeger-LeCoultre after-sales center**, I hope it can help you.