TP LINK TL WR841N ROUTER, DESKTOP CAN BE LOADED, LAPTOP CAN BE USED

You should be logged in to the router of my e-home instead of the TP-Link router. You disconnect the connection between my e-home router and the tp-link router. Then connect your computer directly to the tp-link route, and then enter, the username and password are admin.

If you have set other passwords on tp-link, use a toothpick to hold the reset switch on the back of the router for ten seconds, and the router can be initialized to the factory state, and then enter admin to get in.

In addition, you should set the encryption protocol in TP-link, and instead of WEP, you should choose WAP or WAP2. With WEP, no matter how long you enter your password, someone else can hack it and steal your network.

Supplement: You use a network cable to connect the computer's wired network card interface directly to the LAN port of the TP-Link router, and then use the router to change the password.

Check the unlimited security settings of your wireless settings, where you have chosen the same encryption algorithm and password as you did on your hand.

Wireless Advanced Settings: By default, don't touch anything.

If you have Static Address Allocation turned on, fill in your MAC address.

If you set the static ARP binding settings, you should also fill in the MAC address and the corresponding IP address.

My router is the same as yours, even the brand of the book is the same, hehe

First, whether your router's wireless function is safe to turn on.

Second, the wall is not separated by a large number of weakened models, which will also lead to the inability to access the Internet.

Thirdly (if your router's IP is not set to dynamic) your laptop's IP settings should be in the same group as your desktop, I hope it helps.

Probably you have set up MAC address filtering or turned on a firewall or something.

Here's what you can try. I followed the TP-Link wr340+ explanation, and the setup interface should be about the same.

1. You still need to reply to the factory settings, about 10 seconds or so, there is an explanation on the manual. You've been doing it for so long, you should be able to get it. The default account and password should be admin.

If you want to log in, it is recommended to use Internet Explorer. If you can't log in, unplug the power supply, leave it for more than ten minutes, and then reconnect the power supply and try to log in. Generally speaking, as long as you don't press and hold too hard, the router won't be damaged.

2. After logging in, don't be in a hurry to set a password or set a MAC address, etc., first find the setup wizard, follow the prompts of the setup wizard, select ADSL, and next, enter your broadband account and password. Finalized. You may be prompted to restart, wait a minute, and refresh manually if the interface does not refresh automatically.

3. If you don't understand the MAC address, don't worry about it for the time being.

4. Find the wireless parameters, check the turn on security settings, and the password is taken as an example of the simplest setting

Security type: WEP

Security Options: Automatic.

Key format: ASCII code.

Key 1: Select 64 bits for the key type, and fill in the easy-to-remember password for the key content.

Save. 5. Find the system tool

Modify the login password:

Fill it out by yourself and save it. Then restart your router. When you log in again, you need to enter the login name and login password you filled.

6. If you want to check how many machines are using your wireless network, find the DHCP server, there is a list of clients, you can view.

The steps to set up the router are as follows:

2. Then open the browser and enter the management address and login password of the router.

3. After logging in to the background, click the setup wizard, and then fill in the corresponding parameters according to the wizard instructions.

6. After the wireless setup is completed, click Save, and then restart the router to use it normally.

1. Connect the line between the network cable, the router and the computer, and start the computer and the router equipment;

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface. (If you can't get in, please look at the nameplate at the bottom of the router or the router instruction manual, the default settings of different models of routers are different.) ）

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and click Next directly;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

7. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

1. Log in to the TP-Link WR841N wireless router management page normally, find "Network Parameters" in the home page, and all interfaces must be set here.

Clause. 2. Click "Network Parameters" directly to enter all interface settings, where we can set LAN and WAN, as well as MAC address.

Clause. 3. In the LAN setting, we need to fill in the IP address and subnet mask, which must be filled in correctly, otherwise we will not be able to access the Internet. Then click Save on it, right.

Fourth, the next step is to set up the WAN interface, we directly click "WAN interface settings" to enter this port settings.

Clause. 5. In the WAN interface settings, we can manually set the DNS address provided to me by the service provider. After filling in all the fills, we directly click "Save".

Clause. Sixth, the next is the MAC address setting, this item will basically be automatically detected, you can not move, you can also fill in manually, but you must fill in correctly, otherwise it will affect the Internet.

Here's how to set up the TP-Link WR841N wireless router:

1. Plug the network cable (bus) into the WAN port of the wireless router, plug one end of the network cable into any LAN port of the wireless router and connect the computer network card at the other end, and turn on the power supply of the router.

3. Then enter admin, the default account name and password are the same (there is also a prompt for the original data on the back of the router) to confirm.

4. After entering the wireless router setting interface, select the Internet access method according to the setup wizard (different broadband options are also different), and enter the Internet access account and password.

5. Save and continue to set the wireless key, (it is recommended to use a combination of numbers and English for the password, and it is best to use the @ symbol in the middle, so as to prevent others from rubbing the net).

6. After saving, you can surf the Internet normally.

7. If it is abnormal, you may wish to click the reset button of the wireless router and set up the router again.

After factory resetting the router, configure the steps.

Wiring: The WAN port of the router is connected to the network cable of the broadband modem.

The LAN port of the router is connected to computers, TVs, and set-top boxes.

Settings: If there is no cat, or the cat has a router, the new router should be set to "dynamic IP".

If the cat does not have a router, the new router should be set to "PPPOE dialing", use the account number and password given when handling broadband, and pay attention to distinguishing between "uppercase and lowercase letters" (the computer can no longer dial, you can go directly to the Internet).

The computer network connection is set to "Automatically get an IP address, automatically get a DNS server address".

TP-WR842N Router Wireless Bridging Cannot Get Internet Solution:

After the WDS wireless bridging is set, the bridging status on the management interface of the login sub-router shows that the bridging is successful, but the computer is wired or wirelessly connected to the sub-router and cannot access the Internet. As shown in the figure below:

Troubleshoot this issue by performing the following steps, and then try to access the Internet again after performing each checkpoint.

Note: This article uses the new version of the router as a guide, and the interface of each router may be different, but the troubleshooting methods are the same.

1. Confirm that the IP address of the LAN port is different from that of the main router.

The IP address of the LAN port of the secondary router must be different from that of the primary router, otherwise the terminals on the network may not be able to access the Internet due to address conflicts.

For example, the IP address of the primary router and the IP address of the secondary router are changed. If the primary router is set to, the IP address of the secondary router is changed to .

2. Confirm that the DHCP server is shut down.

Be sure to turn off the DHCP server of the secondary router, otherwise the terminal may obtain an IP address from the secondary router and may not be able to access the Internet. Make sure that only one DHCP server is kept in the network. Find the DHCP server on the management page and click Close.

If the primary router is equipped with data access management functions such as filtering or binding, the terminals connected to the secondary router are not on this list, and the terminals cannot access the Internet. As shown in the figure below, if the Internet access control list does not contain terminals, you may not be able to access the Internet.

It is recommended to turn off the Internet access control, parental control, and ARP binding (IP and MAC address binding) set on the main router, and then try to surf the Internet again.

Note: Many users are unable to access the Internet after bridging due to unreasonable settings of the above functions, please be sure to troubleshoot.

Loops can cause broadcast storms, which can affect your computer's ability to access the Internet.

During the WDS process, please note that:

1. After using WDS bridging, the network cable can no longer be connected between the main and secondary routers. The correct bridging is shown below:

2. If the main and secondary routers are dual-band routers, they can only be bridged with a certain frequency band of 5G, and do not enable WDS for both frequency bands at the same time. As shown below:

If the problem cannot be solved through the above troubleshooting, it may be caused by the compatibility of the router's wireless communication mechanism. You can try to use the main router to connect the WDS wireless router to the secondary router (the roles of the primary and secondary router are reversed) to test whether it can be used normally.

Prepare two network cables (the first one you have ready, which is the one that goes through the "modem").

The second is to buy a network cable sent by the router, if you don't send it, you have to make a network cable with crystal heads at both ends. ）

1.Change the local connection to automatically obtain the IP address.

2.The network cable that comes out of the "modem" is connected to the "wan" port on the router, and the router's ports (1,2,3,4) are either connected to the network cable port behind the computer host.

3.Open the browser and enter the password and username of the router are admin

4.Go to the router settings screen, select the PPPoE (ADSL virtual dialing) method, enter your home account and password, and confirm.

5.Then set the SSID, encryption method, and password.

6.Save, restart. In the end, the setup is considered successful.

That is, you have entered the wrong password, or your router has done a filter, it should be the wrong password