How to lay plastic floor tiles, can the tile surface be covered with plastic flooring

The key to attaching floor tiles is to level the ground, otherwise the floor tiles will be very easy to open or damage in the future. There are many kinds of glue for the flooring plate, which can be purchased by yourself. Paving must be carried out from the center to the periphery, and some glue needs to be left to stand for 1 or 2 minutes after scraping.

After pasting, the glue in the seam should be wiped off.

The key to attaching floor tiles is to level the ground, otherwise the floor tiles will be very easy to open or damage in the future. There are many kinds of glue for the flooring plate, which can be purchased by yourself. Paving must be carried out from the center to all sides, and some glue needs to be left for 1 to 2 minutes after scraping.

After pasting, the glue in the seam should be wiped off.

The main steps of pasting: repairing the flat ground and cleaning it, correcting the room deviation after pasting, compacting the squeegee along the baseline line from the center to the periphery, cutting the pipe at the door frame, cutting the skirting and pressing strip.

I also looked it up on the Internet, and I don't know if it will help you.

Dry paving of floor tiles: cement and sand sprinkled with water and stirred evenly to form a dry and wet dry cement mortar (dry and wet consistency, it is advisable to knead it into a ball by hand and not loose). A layer of cement mortar is laid in advance, (using a one-to-three dry cement mortar) is paved according to the horizontal line, and the bricks are placed on the mortar and compacted with a wooden hammer for plating.

Remove the floor bricks and pour the cement slurry, and then put the floor tiles on the ground to vibrate and flat.

Wet paving of floor tiles: cement and sand and water are mixed evenly to form a wet cement mortar (adding a large amount more than dry hard cement mortar). Before laying, pop up the ground elevation line along the wall, and then make plaster cake around the room, (plaster cake is a cement block used to control the building elevation and the flatness and verticality of the ground when the mason paints or pours the floor.)

The surface of the ash cake should be one piece lower than the ground elevation line, and the floor tiles should be laid with mortar while laying the floor tiles. Finally, use a rubber hammer to smooth the seam.

Explanation: Ground elevation line: It is to set the ground height of the first floor of the room as the zero point of the relative elevation, and use nylon thread or cotton rope to pull out the ground elevation line, as well as the positioning line of vertical crossing. Pave the tiles according to the position of the location line.

Clean the ground base, repair potholes and loose places, then lay out the ground, set the typesetting position, and then brush the ground with super glue, pave the plastic floor when the glue is semi-dry, knock it with a rubber hammer, and wipe off the super glue on the surface of the plastic floor with a clean rag.

It is best to do cement self-leveling first, so that the flatness of the plastic floor will be better.

Summary. "As long as the floor tiles are very flat, they can be laid directly. To use wood needs to be maintained, otherwise it is easy to age.

Plastic flooring is another name for PVC flooring. The main component is polyvinyl chloride material, and PVC flooring can be made into two kinds, one is homogeneous and transparent, that is, the pattern material is the same from the bottom to the surface. There is also a composite type, that is, the top layer is a pure PVC transparent layer, and the bottom layer is a printing layer and a foam layer.

Plastic flooring"It refers to the flooring made of polyvinyl chloride material. PVC flooring is widely used in all aspects of home and business due to its rich colors and colors. Plastic flooring is a broad term.

There are many statements on the Internet, it should be said that they are not very accurate, plastic flooring is a very popular new type of light floor decoration material in the world today, also known as"Lightweight flooring"。

Can the tile surface be covered with plastic flooring?

Hello yes dear.

As long as the floor tiles are very flat, they can be laid directly. To use wood needs to be maintained, otherwise it is easy to age. Plastic flooring is another name for PVC flooring.

The main component is polyvinyl chloride material, and PVC flooring can be made into two kinds, one is homogeneous and transparent, that is, the pattern material is the same from the bottom to the surface. There is also a composite type, that is, the top layer is a pure PVC transparent layer, and the bottom layer is a printing layer and a foam layer. Plastic flooring"It refers to the flooring made of polyvinyl chloride material.

PVC flooring is widely used in all aspects of home and business due to its rich colors and colors. Plastic flooring is a broad term. There are many statements on the Internet, it should be said that they are not very accurate, plastic flooring is a very popular new type of light floor decoration material in the world today, also known as"Lightweight flooring"。

Summary. How to lay construction accessories for wall tile floor plastic flooring: self-leveling cement, special glue for plastic flooring, interface treatment agent, welding wire cold welding fluid, baseboard, edge strip, edge strip, sealing agent waxing water, hard wax wax.

Construction equipment: ground flatness detector, humidity measuring instrument, floor grinder, agitator, self-leveling rake, self-leveling defoaming roller, scraper, mild steel ruler, cutter, vacuum suction machine, drum, grooving machine, welding torch nozzle cold welding fluid, polishing machine, high-grade wax mop.

How to treat the walls with tiles, the floor with plastic flooring, and between the floor tiles and the plastic floor?

How to lay the construction accessories of the wall tile floor plastic floor: self-leveling cement, special glue for plastic flooring, interface treatment agent, welding wire cold welding liquid, baseboard, edge strip, edge strip, sealing agent waxing water, hard wax wax. Construction Equipment:

Ground flatness detector, humidity measuring instrument, ground noise grinding machine, agitator, self-leveling rake, self-leveling defoaming roller, scraper, mild steel ruler, cutter, vacuum suction machine, drum, slotter, welding torch nozzle cold welding liquid, brother call polishing machine, advanced wax mop.

Is it right to turn up the plastic floor on the tile surface?

Dear Yes. The only requirement for plastic flooring to be laid on the ground is that the floor must be level. The floor of your house has been paved with tiles, which means that it is very flat.

Then the lance floor can be laid on top. But you have to consider a good question, which is whether the lance flooring is environmentally friendly. At present, many products in the market are not environmentally friendly.

It is harmful to the human body.

Here's how: Sun infiltrates.

1. Use a thermohygrometer to detect temperature and humidity, indoor temperature and surface temperature should be 15, and shouting line should not be below 5 and above 30 for construction.

2. Use a floor grinder of more than 1000 watts with appropriate grinding discs to polish the floor as a whole, remove the residues such as paint and glue to remove oil, and remove the convex and loose plots and hollow plots must also be removed.

3. After the floor is pasted, the surface of the floor is flattened and the air is squeezed out with cork blocks.

4. Pour a bag of properly self-leveling into a mixing bucket filled with water according to the specified water-cement ratio, and pour and stir while pouring.

5. Dump the stirred self-leveling slurry on the construction floor, it will flow and level the ground by itself.

6. When the coil is paved, fold the end of the coil. Sweep the floor and the back of the roll first, and then scrape the glue on the floor.

7. When the blocks are paved, please turn the blocks from the middle to both sides, and glue and paste the ground and floor surface after cleaning.

8. After the floor is pasted, the surface of the floor is flattened and the air is squeezed out with cork blocks.

9. Then use a 50 or 75 kg steel roller to evenly roll the floor and trim the warping edge of the splicing in time.

After hours, slotting and welding can be carried out.

If you install plastic flooring in your home, it will bring many benefits, and it is very beautiful and durable. How to lay the plastic floor? PChouse will take you to find out.

1. First of all, measure the size of the room, and then cut the plastic floor according to the size, so as to prepare for the paving under the core.

2. Before paving, the indoor ground should be cleaned, especially the dust and impurities on the ground, etc., and the convex position should be shoveled and smoothed, and the depression can be filled with glue and cement in a ratio of 1:2 to paste it, and then flattened with sandpaper. Because only when the ground is clean, it will not affect the effect of future paving.

3. Gluing, which is a crucial process for how to lay plastic floors. Apply glue on the ground according to the size of the floor, and pave a piece after the coating is done, and proceed in turn. However, a width of about 10 cm should be reserved at the seam to facilitate the treatment of the joint after paving.

When attaching plastic flooring, you should also pay attention to aligning the edges, and use a long-handled brush to drive out at any time to compact the floor. Change the number of tombs.

4. Wipe the residual glue extruded out of the joint position in time to avoid affecting the overall appearance of the ground. A thin layer of seam fluid is then applied along the gap to make it more aesthetically pleasing.

5. After the paving is completed, the ground should also be inspected to see if there are no bubbles, whether it is smooth, etc. If air bubbles are found, it is recommended to insert a syringe to suck out the air and then compact it. Only after everything is checked is in order, the plastic floor can be considered to be successfully paved.

Plastic flooring is a type of flooring that many friends will choose when we lay the floor, and there are many boyfriends who will have such questions, after buying plastic flooring, how to pave plastic flooring, next, let us take you to understand,How to lay plastic flooringThe, as well as what are the brands of plastic flooring, I hope it can help everyone.

First, how to lay the plastic floor.

1. When laying, the base must be smooth, solid and dry, because the surface of the plastic floor is smooth and dry, the yin and yang corners are square, there is no edge, no oil, dust and impurities. In order to ensure that the surface of the floor is smooth and not deformed, which is conducive to paving, the back of the floor and the ground should be degreased and dewaxed before paving.

2. Then we have to remember that the floor is tried to be laid according to the positioning line, and the floor that needs to be cut is cut with a cutting knife according to the paving requirements.

3. When the size of the floor is not exactly the same as the size of the room, a certain size should usually be set aside for edging. If the color of the floor is different between the two rooms, the color separation line should be at the place where the door is closed (step line), and the floor of the other color will not be visible inside and outside when the door is closed. Avoid small and narrow strips at the doorway as much as possible.

4. The order of most paving is to pave the positioning belt first, and then pave other parts, and we must remember to pave from the center to the periphery.

5. After the paving is completed, it can be cured with floor wax.

2. What are the brands of plastic flooring?

1. LG Huaos (Tianjin) ****, LGHausys, is the original LG Chemical Industrial Materials Business Division, which was separated from LG Chem in 2009, is a large-scale building decoration materials enterprise in South Korea, and the world's leading manufacturer of PVC doors and windows, wood and aluminum doors and windows, flooring and wallpaper and other decorative materials.

2. Founded in 1886, Dejia Group has more than 12,000 employees, 34 professional production bases, and sales in more than 100 countries and regions.

3. The predecessor of Hua LC is Korea Chemical Industry, since its establishment in 1965, for more than 40 years, it has been developing towards a comprehensive plastic processing enterprise, and is concentrating on building materials such as floor materials, window materials, artificial marble, engineering stone, automotive parts such as GMT, EPP, and interior materials, functional films, decorative sheets and other living materials, and electrical, electronic and communication parts and materials, etc., to cultivate into a future strategic business.

After reading the above article, I believe that friends will have a certain understanding of how to lay plastic flooring and what are the brands of plastic flooring.

In general, it is not recommended to lay tiles on plastic flooring. While it is theoretically possible to lay tiles on plastic floors, this practice can lead to the following problems:

Adhesion problem: Tiles need to be fixed with special tile adhesive, but because the surface of the plastic floor is very smooth, the adhesion of tile adhesive may be very poor, resulting in tiles that are easy to loosen and fall.

Height difference problem: Laying tiles may cause the ground height to increase, which will make the ground uneven, and there may be height differences in parts such as thresholds.

Durability: Plastic flooring is generally softer and more susceptible to damage than ceramic tiles, while ceramic tiles are harder and more durable. Therefore, if tiles are laid on top of the plastic flooring, the plastic flooring may be damaged and damaged.

If you want to lay tiles, it is advisable to remove the plastic flooring first and then re-tile it on the concrete floor to ensure that the floor is strong, flat and durable.

It is generally recommended to remove the plastic flooring before laying tiles.