How to install home heating pipes Home heating pipe installation method

When arranging the system supervisor, it should be coordinated with the use requirements of the building, the heating system schema, and the layout of radiators. It is necessary to strive to save pipes and facilitate installation and maintenance. Supervisors are generally exposed to the surface. When the supervisor is exposed, it should be arranged in the corner of the external wall and the wall between the windows as far as possible.

Before the main pipe is installed, the radiator should be in place, and the riser can be installed only after finding the straightness, so that the size of the main pipe can be accurate. The semicircular bend on the double riser should be accurate and straight, and the branch pipe should be in the middle of the semicircular bend, and it should not be wrong or wrong. After the installation of the pipeline, check the coordinates, elevation, reserved port position and pipe diameter is correct, and then straighten, with a level to calibrate and review the slope, after the adjustment is qualified, and then adjust the elevator bolt U-shaped card, so that it is moderately tight, flat and consistent, and finally weld the stop wrench at the fixed card.

The fork bend of the radiator branch lamp of concealed or semi-concealed installation must be adapted to the corner of the radiator groove wall to achieve beauty, and the branch pipe connecting the radiator should have a slope. The upper and lower water supply branch pipe slope radiator, return water branch slope riser. There is no exhaust device on the top water supply riser, the slope riser of the water supply and return branches, the slope radiator of the water supply branch pipe of the other layers, and the slope of the return branch pipe.

When the radiator branch pipe passes through the wall, in addition to adding a casing, it should also be noted that the branch pipe is not allowed to have a joint in the wall. When installing a valve on a branch pipe, it should be connected to the detachable part on the side close to the radiator. The installation of the radiator branch pipe should be carried out after the installation of the radiator and the riser, or it can be installed at the same time as the riser.

When installing, the steel pipe must be adjusted appropriately before meeting, so as to avoid crooked branches and risers.

The installation of plumbing is done by professionals. If you are not skilled enough, it is easy to cause leakage and uneven heating. Therefore, you may not get a satisfactory answer here, so you have to ask the relevant people.

Many people in life do their own home appliance installation, but because we are not professional in the installation and maintenance of these home appliances, it is inevitable that mistakes will occur in the installation process or lead to the severity of the problem. Below, let the Tuba Rabbit technical staff explain to you: about the installation steps of household heating pipes!

The installation of heating pipes does not seem complicated, but in the process of installation, there is still a certain degree of difficulty in positioning, slotting, etc. Therefore, if you want to install heating pipes by yourself in life, you must first understand some basics about installing heating pipes

1. First of all, it is necessary to measure and arrange the circuit of the heating pipe, to cooperate with the heat dissipation in use, and to facilitate the maintenance of the problem after installation, and it is best to install the heating pipe in the corner or window.

2. In the process of installation, the radiator should be fixed first, and the size of the pipe should be measured. When installing the pipeline, remember to be straight and accurate to the branch pipe when the riser, and there can be no mistakes or mistakes. After the installation is completed, it is necessary to check whether the coordinates and the position of the reserved port are normal, and it is best to measure it with a ruler.

When all adjustments are made, each fixed clamp is welded.

3. If for the sake of aesthetics, you can choose to use concealed installation when installing heating pipes at home, and remember to slope the riser of the backwater branch pipe when installing. In addition, the water supply branch pipes of other layers should be sloped to the radiator, and the main pipe should be in the slope direction. If the radiator branch pipe is over the wall, remember to add a casing.

Then remember to install the valve close to the radiator for easy removal and connection.

How to choose a heating pipe

1.The materials of heating pipes mainly include aluminum-plastic pipes, PPR pipes and PB pipes.

1) Compared with other pipes, the choice of aluminum-plastic pipe is not easy to be corroded, and the aluminum-plastic pipe has good thermal insulation, and can also be bent at will to facilitate installation and maintenance. However, the only disadvantage of aluminum-plastic pipe is that it is relatively higher than other pipes.

2) The material of PPR pipe is very light, and it is not easy to resist corrosion and has good heat resistance, especially long service life.

3) PB tubes also have a long service life and can withstand high temperatures for a long time, but PB tubes need to block oxygen and have a high oxygen permeability.

2.In daily life, we should choose the size of the heating pipe according to the place where it is installed in our home, and then choose the length and size of the pipe according to the actual situation in our home.

Through the above introduction to the installation steps of heating pipes, I hope it can be helpful to everyone in life. If you still want to know more about the Li Feng information of heating pipes, you can pay attention to Tuba Rabbit Decoration Network, China's first decoration network!

You can get it for free

Many people in life are self-employed people who install home appliances, but since we don't install and maintain these home appliances professionally, it inevitably leads to errors or serious problems during the installation process. Let's take a look at the installation steps of the small family series home heating pipe!

Installation steps and tips for home heating pipes.

The installation of the heating pipes does not seem complicated, but during the installation process, there are still some difficulties with positioning, slotting, etc. Therefore, if you want to install heating pipes yourself in your life, you must first know the basics of installing heating pipes:

1. First of all, you must first measure and arrange the heating pipes so that they can be used. Aspects such as the layout of the heat dissipation, as well as the ease of installation after installation, help with maintenance, and it is best to install the heating pipe in a corner or window.

2。During installation, the pipe size should be measured after the radiator is secured. When installing the pipes, remember to make the branch straight and accurate when using the riser and it should not be a mistake or error.

After the installation is complete, the coordinates and location of the port are preserved for acceptance. It is best to use a ruler. After all adjustments, each fixing card position is soldered.

3。If you want to install a heating pipe in your home to hide it, you can choose to use a concealed installation. When installing, remember to return the water pipe to the package riser.

In addition, the water supply branches of the other floors should be inclined towards the radiator and on the slope of the main pipe. If the radiator branches off the wall, remember to add the casing vertically. Then remember to stay close to the radiator when installing the valve for easy removal and connection.

How to choose a heating pipe.

1。The heating pipe materials mainly include aluminum-plastic pipes, PPR pipes and PB pipes.

1) The selection of aluminum-plastic pipes is not easy to corrode compared with other pipes, and the thermal insulation performance of aluminum-plastic pipes is very good, and it can be bent at will for installation and maintenance. But the only disadvantage of aluminum-plastic pipes is that they are relatively higher than other pipes.

2) The material of PPR pipe is very light, not easy to resist corrosion and heat, especially long service life.

3) PB tubes have the same long life and high temperature resistance, but PB tubes need to block oxygen, and the oxygen permeability is relatively high.

2。Everyone buys heating pipes in their daily lives. According to the installation location in the home, measure the size, and then choose the length and size of the pipe according to the actual situation in the home.

Steps and tips for installing home heating pipes.

The above are the installation steps for heating pipes. If you want to know more, please pay more attention to Tuba Rabbit, Tuba Rabbit will provide you with more complete, detailed and updated information. In renovation, nowhere to seek incurable diseases?

You can get it for free

Dear, I am glad to answer for you: the installation method of household heating pipes is as follows: 1. First open the wall and groove, then connect the pipe and test the pressure, do not take off the table after the pressure test, and then check whether the value on the table has changed, if there is no change, it means that the pipe is not leaking.

2. Set the direction of the pipeline, pay attention to the need to set less curves, and the setting of the groove is slightly larger than the pipe diameter. 3. If you find the location of the radiator, you need to test it back and forth, choose the best location, and pay attention to the beauty and safety. 4. Then install the radiator, pay attention to ensure that it is closed, and there can be no water leakage.

5. Detect and test the radiator, and generally leave the valve during construction, and do the stamping test after the installation is completed, so as to ensure that there is no leakage.